BMW Engine Parts for BMW Z4 M Roadster S54 (2003-2008)

Clear BMW chassis

Please ensure your correct model is selected

Turner Motorsport has everything you need to upgrade your BMW through our stages of performance or to keep your car in peak condition with our range of the latest in proven OEM cooling parts. Upgrade your cooling system and engine performance with the selections below to give your BMW a performance and reliability advantage.

Sub-Categories

Sort By:

ECS - Corporate Logo
T#:49996974
Part#: 059235LA01
In Stock
New Item
Sale - Save 20% $ 29.99

This product was last offered at the strikethrough price on
06-14-2026

$ 23.99 USD
Free Shipping
Sale - Save 20%
$ 29.99

This product was last offered at the strikethrough price on
06-14-2026

$ 23.99 USD
Free Shipping

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On older BMWs, the engine ground strap is a thin, non-insulated cable that spans from the engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for E30 (318i/is), E36, E39, E46, and others Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12421737755 and 12421714262.

Show More Show Less
ECS - Corporate Logo
T#:1887246
Part#: 1181228379812KT
Ships on Sep 1, 2026
Sale - Save 25% $ 197.99

This product was last offered at the strikethrough price on
06-14-2026

$ 148.48 USD
Free Shipping
Sale - Save 25%
$ 197.99

This product was last offered at the strikethrough price on
06-14-2026

$ 148.48 USD
Free Shipping
With exposure to heat and elements, your motor mounts will break down with increasing age. A secure mount is vital to reduce drivetrain vibration and transfer as much horsepower to the wheels as possible. These mounts are an upgrade for non-M E36/E46 owners seeking a stiffer mount without sacrificing comfort and ride quality.
Show More Show Less
ECS - Corporate Logo
T#:384350
Part#: 009422ECS01-01
In Stock
Sale - Save 25% $ 103.99

This product was last offered at the strikethrough price on
06-13-2026

$ 77.99 USD
Free Shipping
Sale - Save 25%
$ 103.99

This product was last offered at the strikethrough price on
06-13-2026

$ 77.99 USD
Free Shipping

A beautiful addition and durable upgrade for your engine

Tired of staring at that bright red plastic oil dipstick? Waiting for a way to add a nice touch to your engine bay without going over the top? ECS Tuning is proud to announce our billet aluminum oil dipstick! Designed to OE specifications with an easy-to-read fill line, we offer three different finishes. Available in black, polished, or clear anodized, we have an offering for every type of enthusiast. Not only does it look better, but also performs better. Because of the durability, it is easier to insert than the factory ribbon dipstick. So, no more fighting with your dipstick to re-install it.

Show More Show Less

ECS - Corporate Logo
T#:367060
Part#: 002778ECS01
Ships on Dec 7, 2026
Sale - Save 10% $ 100.99

This product was last offered at the strikethrough price on
06-13-2026

$ 90.89 USD
Free Shipping
Sale - Save 10%
$ 100.99

This product was last offered at the strikethrough price on
06-13-2026

$ 90.89 USD
Free Shipping
Most of the pulleys on your BMW engine are plastic, which become brittle and frail over time and from engine bay heat. A failed pulley could leave you stranded which is why it is vital to inspect the pulleys during routine maintenance. This is an aluminum version of the stock water pump pulley used on the S54 engine in the E46 M3, MZ3, and Z4M. It's the same size and uses the same hardware and the original belt as the stock plastic pulley. But the aluminum will last much longer.
Show More Show Less

ECS - Corporate Logo
T#:637599
Part#: 005944LA01
In Stock
Sale - Save 24% $ 96.99

This product was last offered at the strikethrough price on
05-03-2026

$ 74.10 USD
Free Shipping
Sale - Save 24%
$ 96.99

This product was last offered at the strikethrough price on
05-03-2026

$ 74.10 USD
Free Shipping
This cap is designed to use the original O-ring seal so no special parts are required. The satin black anodize blends in with the rest of your engine bay making this a smart and subtle upgrade. Made in the USA!
Show More Show Less
Mishimoto - Corporate Logo
T#:380389
Part#: MMOCF-BMW
In Stock
$ 88.99 USD
Free Shipping
$ 88.99 USD
Free Shipping
Install a custom oil cooler on your street or track BMW with help from the Mishimoto Oil Line Fitting Kit! This kit has 100% CNC-machined components, including the 6061 aluminum oil line fittings and the 303 stainless steel tie-down plate. This adapter kit is applicable for BMW E36 (Euro oil-housing equipped), E46, and E90 vehicles, and allows for the use of -10AN fittings to route oil to a custom oil cooler setup. This is an ideal upgrade for drivers seeking additional cooling for track environments or for those who would like additional engine bay space for an oil accumulator or supercharger setup. Included in this kit are two stock BMW O-rings for leak-free installation. Features: Allows for use of -10AN fittings for custom oil cooler setup 100% CNC-machined components, including 6061 aluminum fittings and 303 stainless steel tie-down plate Includes durable stock BMW O-rings for leak-free installation Provides additional engine bay space for applications with an oil accumulator or supercharger setup Included as part of the Mishimoto BMW E46 M3 Oil Cooler Kit Mishimoto Lifetime Warranty Included: (1) Stainless Steel Fitting Clamp (2) -10AN Fittings (2) BMW Oil O-rings (1) M8 x 1.25 x 25mm Button-Head Bolt Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov. ​
Show More Show Less

Glyco - Corporate Logo
T#:375823
Part#: 11211706847
In Stock
$ 136.06

This product was last offered at the strikethrough price on
07-15-2026

$ 125.04 USD
Free Shipping
$ 125.04 USD
Free Shipping
Standard bore
ECS - Corporate Logo
T#:582636
Part#: 012290ECS01
In Stock
Sale - Save 5% $ 113.99

This product was last offered at the strikethrough price on
06-14-2026

$ 108.29 USD
Free Shipping
Sale - Save 5%
$ 113.99

This product was last offered at the strikethrough price on
06-14-2026

$ 108.29 USD
Free Shipping
We have seen so many S54 Vanos line failures at the track that we have to offer you a solution. The factory line is prone to failure due to the OEM hard-line - this stainless steel line alleviates the issues imposed by the factory design and enables you to worry less about your Vanos system. We trust ECS Tuning's Exact-Fit Stainless Steel lines for several different applications, and their S54 Vanos line is no exception.
Show More Show Less

Mishimoto - Corporate Logo
T#:597051
Part#: MMOCCLA
In Stock
$ 127.99 USD
Free Shipping
$ 127.99 USD
Free Shipping
WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

ECS - Corporate Logo
T#:394204
Part#: 012018ECS
Ships on Dec 1, 2026
Sale - Save 11% $ 277.99

This product was last offered at the strikethrough price on
06-14-2026

Starting at $ 248.48 USD
Free Shipping
Sale - Save 11%
$ 277.99

This product was last offered at the strikethrough price on
06-14-2026

Starting at $ 248.48 USD
Free Shipping

The main reason all of the VANOS units will eventually fail is because the material used for the sealing rings from the factory is not designed for that type of environment. When this happens the only option that BMW leaves you with is buying a new and expensive VANOS unit with the same sealing rings that failed in your original unit.

The VANOS system found in BMW engines is a great feature (when it’s working properly), keeping your power curve smooth and responsive especially in lower to mid RPM range. What usually goes unnoticed is the gradual loss of power within this range as the vehicle's age due to slowly failing seals within the VANOS unit. The way the VANOS system works is based off of oil pressure triggered by a solenoid that allows for a small range of timing degree adjustment, this is where the power curve is affected. When the seals begin to fail (all of them do) there is less pressure to advance the timing reducing the power in that low to mid range. Because this happens slowly it's very hard to notice a difference until you refresh your VANOS unit, then you easily realize the response you've been missing.

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

While you're replacing the seals in your VANOS unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy VANOS clatter.

Seals & O-rings:

The seals  were the main focus of this project since the OE units are built with Buna-N rubber o-rings instead of the ECS supplied Viton rubber o-rings. The Buna-N material quickly hardens from the heat and chemical exposure within the engine, where the Viton is significantly more resistant to these chemicals. This knowledge was also used when it came to the commonly failed o-rings found on the VANOS seal plate, replaced at the solenoid.

Rattle Repair:

When it comes to the VANOS rattle this is commonly described as "marbles in a can", and can be heard throughout the different RPM ranges depending on the engine. These upgraded rings and washers are precision ground from hardened steel to resist wear and deformation keeping your VANOS rattle free. The rattle repair tools are designed specifically for this VANOS anti-rattle repair, design from hardened steel to stand up to the job. Designed to perfectly follow the splines of the shaft for a tight grip when applying the necessary torque to disassemble & reassemble the VANOS transfer gear. The keyed socket was designed with the intent to use a "common" wrench so this can be completed at home in your garage.    

When Servicing your VANOS unit we recommend getting everything you need to replace on the way to service which includes an oil change and valve cover gasket set. Fresh oil and gaskets is the best way to start off a fresh rebuild of any kind giving you the maximum performance of your freshly serviced components.

Don't forget to check out our rebuild PDF to make sure you have everything to get the job done and eliminate the rebuild guess work.

 

This item fits the following BMWs: 
2000-2001 E46 3 Series M3 M3 Convertible 2000-2006 
2001-2002 Z3 Roadster / Coupe Z3 M Roadster Z3 M Coupe w S54 Engine 
2006-2008 E86 E86 Z4 Z4 M Roadster Z4 M Coupe

 

Show More Show Less
Mishimoto - Corporate Logo
T#:372557
Part#: MMOCCCF
In Stock
$ 162.99 USD
Free Shipping
$ 162.99 USD
Free Shipping
Universal kit with a catch can and rubber hose; for retrofitting on a variety of vehicles. Carbon fiber catch can prevents a harmful buildup of oil inside of the turbocharger, intake manifold, intercooler and piping. Separates oil particles from PCV/CCV air Defends intercooler, intake system, and essential components from oil blow-by Made from lightweight carbon fiber Compact design makes for easy engine bay placement Checking fluid levels made easy with built in sight tube Comes complete with mounting bracket, hose, all necessary clamps, fittings, and mounting hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
Performance Tool - Corporate Logo
T#:1809130
Part#: W89409
In Stock at Vendor
$ 126.99 USD
Free Shipping
$ 126.99 USD
Free Shipping
For servicing overhead valve engine with cylinder head removed.


ECS - Corporate Logo
T#:585720
Part#: 11211706847WPCKT
In Stock
Sale - Save 3% $ 250.99

This product was last offered at the strikethrough price on
06-14-2026

$ 243.46 USD
Free Shipping
Sale - Save 3%
$ 250.99

This product was last offered at the strikethrough price on
06-14-2026

$ 243.46 USD
Free Shipping
What's better than using new crank bearings in your next engine build? WPC-treated bearings! What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both. What are you waiting for? Use WPC-treated bearings on your next engine build or crank service!
Show More Show Less
Mishimoto 19 Row Universal Oil Cooler
For custom applications only. Not a direct bolt on.
Mishimoto - Corporate Logo
T#:378414
Part#: MMOCUL
In Stock at Vendor
$ 536.99 USD
Free Shipping
$ 536.99 USD
Free Shipping
Even under optimum driving conditions increased oil temperatures will cause a drop in pressure and will decrease the ability for your engine to be properly lubricated. With this new oil cooler, you can keep your oil temperatures down for optimum driving conditions. The kit includes four-feet of stainless braided line, adapter fittings, and oil filter sandwich adapter. Rows: 19 Overall Dimensions: 13" x 5.5" x 2" Core Dimensions: 11.25" x 5.5" x 2" Braided Hoses: 4ft .75 inch & 4ft 9 inch Braided Hose Fittings: -10AN Sandwich Plate Fittings: -10AN WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
Mishimoto Universal 10 Row Oil Cooler
For custom applications only. Not a direct bolt on.
Mishimoto - Corporate Logo
T#:378421
Part#: MMOCU
In Stock at Vendor
$ 410.99 USD
Free Shipping
$ 410.99 USD
Free Shipping
This universal oil cooler from Mishimoto is far superior to the factory unit with its 11" x 2.76" x 1.97" core. Even under optimum driving conditions increased oil temperatures will cause a drop in pressure and will decrease the ability for your engine to be properly lubricated. With this new oil cooler, you can keep your oil temperatures down for optimum driving conditions. The kit includes 4 feet of stainless braided line, adapter fittings, and oil filter sandwich adapter. Mishimoto Automotive is a leading manufacturer of aftermarket performance cooling products. The company was established back in 2003 with one goal. That goal was to provide customers with quality cooling system upgrades that work on the track and on the road. At Mishimoto, you never have to worry about the quality of the product you are installing. This kit is universal and is not a direct bolt on. *For custom applications only. Not a direct bolt on. WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less

Glyco - Corporate Logo
T#:375824
Part#: 11211706850
In Stock at Vendor
$ 126.61

This product was last offered at the strikethrough price on
07-15-2026

$ 118.92 USD
Free Shipping
$ 118.92 USD
Free Shipping
59.75MM(+0.25) bore

ECS - Corporate Logo
T#:384352
Part#: 009422ECS01-03
Ships on Dec 7, 2026
Sale - Save 25% $ 96.99

This product was last offered at the strikethrough price on
06-13-2026

$ 72.74 USD
Free Shipping
Sale - Save 25%
$ 96.99

This product was last offered at the strikethrough price on
06-13-2026

$ 72.74 USD
Free Shipping

ECS Tuning introduces the solution to your engine bay aesthetic concerns with the Billet Aluminum Oil Dipstick. Say goodbye to the bright red plastic eyesore and elevate your under-the-hood style effortlessly. Designed to OE specifications, this dipstick boasts an easy-to-read fill line and is available in three stunning finishes: black, polished, or clear anodized.

  • Billet aluminum construction for enhanced durability
  • Easy-to-read fill line for convenient oil level checks
  • Available in three finishes: black, polished, or clear anodized
  • OE specifications ensure a perfect fit
  • Improved ease of insertion compared to factory ribbon dipstick
  • Aesthetic enhancement for your engine bay

Upgrade your engine bay's appearance and functionality with the ECS Tuning Billet Aluminum Oil Dipstick. No more struggles reinstalling your dipstick; enjoy a sleek and high-performing addition to your vehicle.

Show More Show Less
Glyco - Corporate Logo
T#:374672
Part#: 11211706852
Back Ordered
$ 111.99

This product was last offered at the strikethrough price on
05-07-2026

$ 108.99 USD
Free Shipping
$ 108.99 USD
Free Shipping
59.75MM(+0.25) bore

Glyco - Corporate Logo
T#:374670
Part#: 11211706849
Back Ordered
$ 177.99

This product was last offered at the strikethrough price on
05-07-2026

$ 172.99 USD
Free Shipping
$ 172.99 USD
Free Shipping
Standard bore