BMW Drivetrain Parts for BMW X Series E83 (2004-2010)

This is an OEM LuK stock twin mass flywheel for the N52 non-turbo engine in the 128i, 325i/328i/330i, 525i/528i/530i, and Z4 30i. It's manufactured by OEM supplier LuK. Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.

Stock rubber flex discs allow for a slight amount of give, especially under heavy acceleration and, depending on the amount of force applied, could potentially tear or split. This slight flex/give can prevent instantaneous transfer of force to the wheels, making accelerations unpredictable, or even lead to your vehicle being stuck on the side of the track. To combat this, IRP's Performance Flex Disc was developed. Made of CNC machined aluminum, this flex disc won't actually flex, and the polyurethane bushings will only provide a enough give to dampen some vibrations and prevent damaging the transmission. This is perfect for high torque applications such a drag cars and dedicated track cars that want immediate response and long term reliability.

110mm Diameter

This item fits the following BMW Chassis: 
E60 M5,E63 M6,E63,E90,E92,E93 

Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.

By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components. 

Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved acceleration response, more direct shifting feel and overall improved drivetrain composure with Powerflex performance polyurethane bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

Upgrade the holding power of your clutch with the Clutch Masters FX250 clutch kit.

FX250 (Stage II)

• Extra long life street system
• Holding capacity 70% over stock
• Heavy-Duty reinforced pressure plate
• Rigid organic/fiber tough disc

All Clutch Masters clutch kits come complete with:

• Pressure Plate
• Clutch Disc
• Throw-out Bearing
• Pilot Bearing or Bushing
• Alignment Tool

Fitment in following BMWs:This item fits the following BMWs: 
2003-2005 E46 BMW 330i 330ci  only for 6-speed manual transmission 

Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.

By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components. 

Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved acceleration response, more direct shifting feel and overall improved drivetrain composure with Powerflex performance polyurethane bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

BMW E36 Z3 Stage 1 Single Sprung Organic Clutch and Flywheel Kit from Turner Motorsport offers a high-performance solution with a lightweight design for improved throttle response and exceptional torque capacity. Ideal for high-performance racing applications, this kit provides the ultimate balance between drivability and power.

• Lightweight Design: Enhances throttle response and overall driving dynamics.
• High Torque Capacity: Supports up to 340 ft/lbs of torque, making it suitable for performance-driven applications.
• Precision Engineering: Features the latest pressure plate design and friction material for optimal balance between drivability and performance.
• Enhanced Pedal Feel: Carefully analyzed pivot point and diaphragm design ensure positive pedal feel and increased clamping force.

Specifications:

• Clutch Disc Diameter: 9.448"
• Clutch Disc Spline: 10
• Disc Material: Organic
• Disc Type: Sprung Solid
• Input Shaft Diameter: 1.140625"
• Flywheel Step: -3.8mm
• Maximum Torque Capacity: 340 ft/lbs
• Recommended Use: Street Use

Includes:

• Single Mass Flywheel
• 1 Sprung Organic Clutch Disc
• Pressure Plate
• Flywheel Bolts
• Pressure Plate Bolts
• Release Bearing
• Alignment Tool
• Clutch Spline Grease

XClutch performance upgrades are developed with over 30 years of experience and advanced testing facilities, offering top-notch engineering for both street and race applications.

OEM LuK Clutch Kit includes Clutch Disc, Pressure Plate, and T/O Bearing. Call for applications not listed above. SACHS is the OEM supplier for BMW. OEM replacement for BMW part # 21207531556, 21207553768, 21207575556, and 21217523622.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Don't neglect your motor mounts! Most stock BMW motor mounts are fluid filled and the stiffness of the mount depends on this fluid. But over time the fluid leaks out and the strength of the mount is greatly reduced. A worn motor mount allows the engine to twist and shift around. The harder you're driving the more shift will occur. As the engine is moving around it can contact other parts in the engine bay - usually cooling related. The mechanical fan can hit the radiator; the A/C compressor can hit a radiator hose, the exhaust will flex and may break. Twisting of the engine can also lead to shifting problems as the transmission twists with it. There are countless issues related to worn or compressed motor mounts so don't overlook these as a regular replacement item (every 50,000 miles).

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Genuine BMW Rubber Mounting Right -
This item fits the following BMW Chassis:
E83 X3