BMW Engine Parts for BMW X Series E83 (2004-2010)

Enhance your BMW's performance with the upgraded BAV Ignition Coil, designed to boost firepower and optimize engine efficiency. These coils boast modified core windings for a faster, more efficient burn, resulting in increased torque at lower RPMs and heightened horsepower in the upper range. While improvements depend on your engine's condition, these coils ensure noticeable enhancements in performance and potential fuel economy benefits.

Product Benefits:

Improved engine firepower and efficiency
Increased torque at lower RPMs
Enhanced horsepower in higher ranges
Potential improvement in fuel economy
Set of six for complete BMW Cooper replacement

When servicing your vehicle's VANOS system, get the job done easier with this socket specifically designed for the removal of the VANOS solenoid.

Features:

• 85mm from end to end
• 1/2" drive 
• 32mm with a depth of 70mm.

Elevate your BMW maintenance with this comprehensive tool kit designed for valve and valve stem seal removal and replacement, all without the need to remove the head. This time-saving kit ensures efficiency and ease in the process, making it an essential for DIY enthusiasts and professionals alike. The universal fitment and a range of adapters guarantee versatility across various brands and motors, providing maximum utility.

• Removes and replaces valves and valve stem seals without head removal
• Time and effort-saving solution
• Wide range of adapters for versatile use
• Universal fitment for compatibility with different brands and motors
• Essential for DIY and professional use

Contents:

• 1 - Lever Bar
• 4 - Valve Spring Compressor Adapters
• 1 - Slotted/Notched Pulling Device
• 1 - Hook Pulling Device
• 1 - Connector for Valve Spring Adapters
• 1 – Connector for Pulling Device
• 1 - Extension for Valve Spring Adapters

If you have ever attempted to do a valve job or cylinder head gasket project on an M42, M44, M50, or M52 engine you know that the repair manual will refer to the special BMW timing tool kit. This tool kit includes a flywheel locating lock pin, and a special set of camshaft locators that lock the cams in a precise location. The tools are very easy to install. The kit is specifically designed to hold the engine and cams in proper timing during the cylinder head removal and re installation process. This avoids the chance of bending the valves doing the head install process. The precision ground holding blocks lock over the square ends of both intake and exhaust cams. The CNC machined flywheel locating pin passes through a hole in the rear of the engine block and passed through a machined hole in the flywheel.

To avoid improper cam timing on the latest BMW engines, the factory has devised a cam timing system that locks the crankshaft and cams into a specific position prior to cylinder head removal. This method was devised to avoid any misalignment, resulting in piston to valve damage. Unfortunately without these tools re-timing the camshafts after a valve job is almost impossible. The factory specification manual does not supply installation specifications. This cam timing kit includes all the necessary components to do the job.

This item fits the following BMWs:
1990-1991 E30 BMW 318i 318is 318ic
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi

NOTE: Not compatible with S50B30 and S50B32 Euro engines!If you have ever attempted to do a valve job or cylinder head gasket project on an M42, M44, M50, or M52 engine you know that the repair manual will refer to the special BMW timing tool kit. This tool kit includes a flywheel locating lock pin, and a special set of camshaft locators that lock the cams in a precise location. The tools are very easy to install. The kit is specifically designed to hold the engine and cams in proper timing during the cylinder head removal and re installation process. This avoids the chance of bending the valves doing the head install process. The precision ground holding blocks lock over the square ends of both intake and exhaust cams. The CNC machined flywheel locating pin passes through a hole in the rear of the engine block and passed through a machined hole in the flywheel.

 

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Discover the ultimate solution for your MINI Cooper's N12, N14, N16, and N18 engines in the R56 chassis – our MINI Cooper Front Crankshaft Seal Installer. This tool simplifies the installation process effortlessly. Just follow these easy steps: Tighten the three inner bolts to attach the inner piece onto the front crankshaft. Then, insert the seal into the outer portion of the tool. Place the outer portion over the now-attached stud and utilize the included pushing nut to apply uniform pressure, securely seating the seal onto the front crankshaft.

Crafted from robust materials, this tool is indispensable for both mechanics and DIY enthusiasts. Say farewell to laborious manual installations and welcome a quick, precise solution into your automotive toolkit. Upgrade your equipment today and make perfect seal installations a breeze.

This tool will also work on select BMW engines, please check fitment by entering your vehicle information!

Schwaben Professional Mechanic's Work Gloves provide exceptional hand protection with a perfect balance of durability and comfort.

Designed for precision, these gloves offer high dexterity, making it easy to handle even the smallest parts. The tailored elastic cuff with a hook-and-loop closure ensures a secure and comfortable fit.

The textured latex coating on the palm and fingertips delivers superior grip and tactile feedback, while the breathable spandex backing and knit top allow for all-day comfort.

The durable synthetic leather palm enhances longevity, and the unique graphic design reflects the drifting culture of Euro car enthusiasts.

Note: See manufacturers information tab for sizing chart.

Key Features:

• High Dexterity: Perfect for picking up small parts with ease.
• Secure Fit: Tailored elastic cuff with a hook-and-loop closure.
• Enhanced Grip: Textured latex coating on palm and fingertips.
• All-Day Comfort: Breathable spandex backing and knit top.
• Durable Design: Synthetic leather palm for extended wear.
• Unique Style: Graphic design inspired by the drifting culture of Euro owners.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Perfect for any job when it comes to keeping your hands clean and protected.

Features:

• High dexterity
• Elastic hook and loop strap
• Textured latex finger tips for grip
• Breathable material

Schwaben Professional Mechanic's Work Gloves provide exceptional hand protection with a perfect balance of durability and comfort.

Designed for precision, these gloves offer high dexterity, making it easy to handle even the smallest parts. The tailored elastic cuff with a hook-and-loop closure ensures a secure and comfortable fit.

The textured latex coating on the palm and fingertips delivers superior grip and tactile feedback, while the breathable spandex backing and knit top allow for all-day comfort.

The durable synthetic leather palm enhances longevity, and the unique graphic design reflects the drifting culture of Euro car enthusiasts.

Note: See manufacturers information tab for sizing chart.

Key Features:

• High Dexterity: Perfect for picking up small parts with ease.
• Secure Fit: Tailored elastic cuff with a hook-and-loop closure.
• Enhanced Grip: Textured latex coating on palm and fingertips.
• All-Day Comfort: Breathable spandex backing and knit top.
• Durable Design: Synthetic leather palm for extended wear.
• Unique Style: Graphic design inspired by the drifting culture of Euro owners.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Battery Terminal brush uses the external brush to clean the cable clamps and the internal brush to clean the battery posts. Made from high Impact plastic body to eliminate tool corrosion.

Keeping the connection clean is an important part of making sure your battery is transferring the proper voltage during startup.