BMW Tools & Specialty Equipment for BMW E12 530i M30 3.0L

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

This professional-grade deluxe fender roller allows you to gently and gradually flatten your inner fender lips in order to increase your fender to tire clearance.

This new deluxe fender roller has been designed to fit most applications.

This is the perfect tool for:

If you want to lower your vehicle
If you want wider-than-stock wheels
If you are going to use wheel spacers or decreased offset
Will work with bolt patterns of 4x100 and 5x100 up to 4x114.3 and 5x130 with 12mm or 14mm lug bolts.

By rolling the fender lip flat, you can lower your car further, and give your car a wider stance, without your tires rubbing on the inside of the fender.

Fully adjustable for use on vehicles of different ride heights, offsets, and wheel bolt patterns.

Use of a heat gun is recommended to soften the fender surface during the rolling process and prevent paint cracking.

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

Due to clearance issues, many types of lifts require specific adapters that are made for reaching SUV and truck jack points. This 12-piece kit has been made by using stackable adapters that mount inside the lifting block trays so that vehicles with high ground-clearance or those with unique jack point locations are better accommodated. These adapters offer up to 7.2" of additional height when all combined.

Complete kit includes:

• Low‐profile round polyurethane contact pads  -  Qty: 4
• Sliding receivers that accommodate the round polyurethane contact pads and/or the stackable adapters  -  Qty: 4
• 3" stackable adapters.  -  Qty: 4

Fits BL-5000SLX/EXT and BL-7000SLX/EXT Series Only.

 This comprehensive kit is basically a one-stop-shop to pick up all the special torx, triple square, & hex bits you need to keep your car where it should be... on the road!

This Universal European Tool Kit features the following:

• Torx Screwdriver Kit - 6 Pieces (Sizes included: T10, T15, T20, T25, T27, & T30. Perfect for removing door and dashboard panels, interior trim, and smaller underhood components. )
• Swivel Head Triple Square Driver Kit - 4 Pieces (Set of four 3/8 drivers in M6, M8, M10, and M12 sizes. Perfect for working around corners in those hard to reach spots.)
• Specialty Bit Kit - 100 Pieces (100 piece torx & hex bit kit to fit a wide assortment of automotive fasteners. Made of hardened Chrome Vanadium steel, packaged in a handy blow molded case.)
• Go-Through Screwdriver Kit - 6 Pieces (Kit includes durable slotted & phillips head nickel-chromoly screwdrivers with hardened shafts that extend the entire length of the driver.)

These QuickJack rubber contact blocks are used with all QuickJack systems and can be used with other QuickJack pads or are perfect to replace missing pads.

These blocks are made of a hardened rubber that has specifically been formulated to resist gouging, cutting, and abrasion. They are also resilient against chemicals and solvents that would normally damage rubber.

Dimensions: 6.5" long x 1.5" tall x 4" wide

When it comes to the torque found on axle nuts you're already looking at using a breaker bar or impact gun not to mention the corrosion collected over the years. The safest approach is using impact socket, since they are built with the strength needed to avoid breaking under pressure.

Features:

• Heavy duty ½ inch-drive sockets and drivers have extra thick alloy steel walls, and take a beating that would destroy normal sockets
•  Durable black oxide coating wipes clean easily and resists rust
• Contains three 12-point sockets for a sure grip on the most common sized axle nuts, plus three hex drives for removing common hex-head plugs and fasteners
• Conveniently packaged in a blow molded case, this set will please the most demanding professional technician or discriminating prosumer

Kit includes:

• 30mm, 32mm, and 36mm - 12-point axle nut sockets - ½" drive

• 14mm, 17mm, and 19mm hex head drive axle shoulder bolt sockets - ½" drive

Urethane Pinch-Weld Block - Set provides a superior solution for supporting vehicles on pinch-weld rails. Traditional rubber blocks can cause damage to delicate body rails due to excessive pressure points. These urethane pinch-weld blocks are engineered with a cross-cut slotted design, allowing versatile positioning either lengthwise or crosswise. They are ideal for safely supporting rocker panels or sheet metal body rails, particularly those that have degraded from corrosion over time.

• Specially formulated urethane rubber for durability
• Deep bilateral slots accommodate virtually all pinch weld frames
• Versatile positioning: lengthwise or crosswise
• Water, chemical resistant, and 100% weatherproof
• Single-piece construction ensures a superior hold
• Dimensions: 3.9” (L) x 2.9” (W) x 2.4” (H)

Harmonic Balancer Puller and Installer Set

The Harmonic Balancer Puller and Installer Set is an essential tool kit designed for the effective removal and installation of harmonic balancers. This master set includes all the necessary bolts and adapters required for a wide range of applications, making it a versatile addition to any workshop or toolbox.

Benefits:

• Comprehensive Set: Includes all required bolts and adapters for most applications, ensuring compatibility with various vehicle models.
• Bilingual Instructions: Comes with bilingual instructions for easy use and understanding, catering to a broader range of users.
• Replacement Part Availability: Replacement parts are readily available, ensuring the tool kit remains functional and useful over time.
• Efficient Performance: Streamlines the process of removing and installing harmonic balancers, saving time and effort.
• Durable Construction: Built from high-quality materials for long-lasting durability and reliable performance.