Select Vehicle
BMW
Mini
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
The Turner Motorsport Oil Temperature Sensor Flange was designed to get your oil temperature from the best possible location: the sump. Most of the factory and aftermarket sensors are located after the oil pump, which does not give you an accurate temp reading of the oil that is actually lubricating the engine. At the factory temp sensor location the sensor picks up heat not only from the oil stream, but also from the oil pump and housing which will skew the reading. Other aftermarket adapters can be give inaccurate readings from their location and/or design limitations. And may require making unnecessary modifications. By relocating the sensor to the oil sump it reduces clutter and sits flush against the bottom of the oil pan to avoid potential clearance issues. Testing that we have done on and off the track shows that the sump location is the most accurate. We accomplish this by removing the factory oil level sensor or block off plate and using the existing hole and bolt pattern on the oil pan with no additional modifications. Any sensor with an M12 x 1.50mm thread can be used in the flange.
Note that removing the factory oil level sensor will trigger the low oil fault/warning light. There's no elegant way around this but since the Temp Flange is considered a race-only part we assume you will be checking your own oil level anyway or be using a stand-alone dash/engine management system that does not track oil level. And having the most accurate oil temp is more important.
Applications:
1987-1991 E30 M3
1992-1999 3 Series E36 M3 3.0 and M3 3.2 Euro Models Only!
1999-2006 3 Series E46 All
1991-1995 5 Series E34 525i M50
1997-2003 5 Series E39 525i, 528i, 530i, 540i, 540iP, M5
2004-xxxx 5 Series E60 525i, 530i
1995-2001 7 Series E38
Z3 2.5, 2.5i, 2.8, 3.0i, M3.2 S54
Z4 2.5, 3.0
Z8 All
When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.
Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain system comes complete with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.
Features:
When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.
Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain hole can be used with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.
Features:
Upgrade your engine build with Turner's WPC-treated Race Series Bearings, engineered for serious performance enthusiasts. Starting with ACL’s high-performance bearing shells, these Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.
Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.
Key Features:
Duraglide Tri-Metal Construction: ACL's Race Series bearings feature a high-strength overlay for enhanced performance. Optimized Oiling: Designed to promote better oil flow during high-RPM conditions. Precise Fitment: Manufactured with OEM-level precision using micron tolerance machining. WPC-Treated for Strength: Surface treatment adds strength and reduces friction for improved engine performance. No Flash Plating: Allows for better heat transfer and bearing retention. Thermal Discharge Process: Smoother, stronger components through WPC’s unique thermal discharge technology. Enhanced Heat and Friction Resistance: Built to combat the biggest enemies of high-performance engines. Don’t settle for standard bearings—choose Turner Motorsport WPC-treated Race Series Bearings for the ultimate engine performance upgrade. Perfect for your next engine rebuild or rod bearing service!
One of our most popular items! We have been selling our S14 stroker kit since 1993. Since then we have sold HUNDREDS of this exact kit, and have received incredible feedback from our customers. RELIABLE Horsepower is our goal. Our E30 M3 2.5L Stroker kit uses factory BMW Evolution III parts to convert the stock 2.3 liter engine into the Evolution III 2.5 liter engine. Increasing the displacement and raising the compression yields much more torque: +50 ft/lbs @ 4000 rpm. With a stock head our 2.5 kit will make over 225 hp.
Our kit includes everything you need to convert your 2.3L into a 2.5L. We highly recommend upgrading the intake and exhaust system to allow larger 2.5L engine to breath. Call for more details and for "custom" packages. We can set you up with any other engine components you may want to replace (tensioner rails, chain guides, oil pump, etc) at the same time. For your benefit, we carry all these items (and at a great price).
The Turner 2.5 liter S14 Stroker Kit includes:
The No-Compromise Oil Pan for Your 24V E30 Build
Every E30 swap story starts the same way: you want the reliability and power of a modern BMW 24V engine - M50, M52, S50, or S52 - but without heavy modifications or a list of oil pan parts that are no longer available(NLA). You’ve read the forums, seen the DIYs, and done the math. And you’re still faced with the same question: how am I going to find all of these parts and make them work?
That’s exactly the problem we set out to solve.
At Turner Motorsport, we’ve been building BMWs for decades. We've performed the swaps, turned the wrenches, and taken the laps. The Turner Fabricated Oil Pan was born out of that experience, an enthusiast-engineered solution that eliminates the guesswork and lets you focus on what really matters: driving.
We designed this oil pan from the ground up to support 24V engine swaps into the E30 chassis, with zero permanent modifications.
Crafted from TIG-welded 5052 aluminum, this pan is as durable as it is lightweight. The brushed anodized finish adds a subtle shine under the hood and guards against corrosion for long-term reliability. Inside, we’ve integrated full-length oil control baffles with trap doors, ensuring your oil stays where it needs to be, even under the most aggressive acceleration, braking, and cornering.
The low-profile design is perfect for lowered cars, and the 8 mm-thick flange ensures a proper seal with the factory gasket. We didn’t stop there, every pan includes a billet aluminum oil pickup with an integrated stainless mesh screen that’s fully serviceable, a 304 stainless steel dipstick tube, and a billet rear transmission plate that allows you to utilize the lower mounting holes, unlike the stock E34 pan.
Whether you're building a high-performance street car, a dedicated track weapon, or a clean restomod, this oil pan offers OEM-level integration with aftermarket performance. It’s the cleanest, easiest, and most effective way to run a 24V engine in your E30 — built by BMW lovers, for BMW lovers.
Design:
Fully TIG-welded 5052 aluminum construction
Brushed anodized finish for a clean look and corrosion resistance
Engineered specifically for M5X/S5X engines in the BMW E30 chassis
Front-sump design clears the factory E30 subframe, no cutting or modification required
Designed and tested in-house by BMW enthusiasts
Features:
Built-in oil control baffles with trap doors to prevent starvation under cornering
Low-profile design for maximum ground clearance - perfect for lowered cars
Billet aluminum oil pickup with integrated stainless mesh screen - fully serviceable
8mm thick flange ensures a reliable seal with OEM gasket
Works with all standard 24V swap motor mounts
3/8" NPT port for turbo oil drain and 1/4" NPT for OBD2 CCV drain
Compatible with G260 and ZF transmissions
Stainless steel dipstick tube (304) included for strength and appearance
Utilizes E36 Dipstick (P# - 11431427993)
Kit Contents:
Turner Fabricated Oil Pan
Billet Rear Mounting Plate
304SS Dipstick Tube with Mounting Hardware
Billet Aluminum Oil Pickup
Optional: Oil Pan Gasket, Oil Filter, and Motor Oil
Optional: Complete Install Hardware Kit
Why It Works:
Direct fitment for M5X/S5X into E30, no cutting or fabrication required
Maximum clearance for front subframe, steering rack, and lowered suspension setups
Track-proven baffling to prevent oil starvation under load
Transmission compatibility with G260 and ZF gearboxes
Built by enthusiasts, designed and tested in-house on real cars
Group A racecars were the top of their class in both touring car and rally racing. Heavily modified and extremely fast these cars set out to demonstrate the best of what a manufacturer could do on the racetrack. It was the predecessor to the current DTM class racing and set a standard for many other divisions of motorsport to follow.
One of the weaker points of the S14 engine, when speaking from a racing standpoint is the belt drive system. While fine for a street going car, a V-belt is not suitable for high RPM applications. On the track, most of your time will be spent in the higher rev range which puts extreme amounts of stress on the factory setup. BMW realised this and came up with a solution that involved doing away with the V belt system and using a 6 rib serpentine style instead.
Extremely resistant to slippage and failure this design holds up much better the abuse of track duty and won't leave you stranded and waiting for tow back to the pit. Additionally, this kit does not accommodate and a/c compressor and the alternator and waterpump are underdriven by way of slightly larger pulleys. Combined, this puts less of a load on the crankshaft which leads to more efficient power delivery to the ground. If you track you E30 M3, this is an essential upgrade and until now was extremely difficult to source. Do not skip this pivotal step in your engine build or overhaul and get a leg up on the competition the Group A way.
Please note this kit is special order and in non-returnable
Features:
This kit fits the following BMWs:
1986-1992 BMW M3 All