Free Shipping on orders $99 and up! Some exclusions apply. Contiguous US only.

BMW E30 M3 Camber / Caster Kits

BMW E30 M3 Camber / Caster Kits The camber setting in your alignment is one of the most crucial aspects of your suspension and the overall driving experience. Unfortunately, most BMWs do not have a camber adjustment in the front and a limited adjustment in the rear. This can be frustrating because camber comes into play whenever you make changes to the suspension or when you want more negative camber for more grip and better handling. There are multiple reasons to adjust camber -

•  You want more front end grip to reduce understeer and create a more balanced handling scenario,
•  You have lowered the car and need to reduce negative camber due to inside tire wear
•  You added wider tires or wheels and need extra clearance to bodywork,
•  Your car was in an accident or collision and the camber setting is now wrong. Note: there may be other factors to this situation and we recommend finding the root cause rather than a quick-fix.

We offer front fixed or adjustable camber plates or camber/caster plates, rear adjustable camber arms, and rear adjustable camber bushings from KMAC, Vorshlag, and also our own designs to fit your specific needs. In most cases, these adjustable camber kits are a direct replacement for the stock BMW part, enabling a seamless upgrade. Adjustable camber can be dialed-in using ordinary hand tools and most kits have reference marks for consistent and repeatable adjustments. No drilling, slotting, or welding required! Some kits perform specific functions and fit with specific types of suspensions (stock, stock-type, coil-over, etc). Give us a call if you need guidance in selecting the best camber plate option for your particular suspension or situation.
You're currently viewing parts for your (E30) M3 1988-1991. Reset your chassis
For accurate results, specify your model below.
Turner Motorsport Street/Track Front Fixed Camber Plates - E24, E28, E30

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

These fixed steel camber plates for your E30/E24/E28 will add 3/4 degree of negative camber and will reduce understeer during hard cornering and save the outside edge of your tire. These plates mount to the top of the upper strut bearing and relocate the top of the strut further in. Combine these with the BMW offset upper strut bearings for even more negative camber. These are the perfect camber solution when adjustable plates are not allowed in your class. We used these in our ultra-successful J-Stock suspension as they maximize the available camber in the tire well when using the large, stock-diameter springs.

 

Instructions for Turner E30 Front Fixed Camber Plates


This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is M3

Turner Motorsport
Part #: TSU3080459
Price: $139.95 (USD) 
In Stock
Free Shipping Free Shipping
Quantity:   
KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E24, E28, E30, E34 Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1984-1991  E30 BMW  318i 318is 318ic 325e 325es 325i 325ic 325is M3
1982-1988  E28 BMW  528e 533i 535i 535is M5
1993-1995  E34 BMW  525i
1982-1989  E24 BMW  633csi 635csi M6
KMAC
Part #: 193316-1J
Price: $380.00 (USD) 
Ships on Jul 9, 2018
Free Shipping Free Shipping
Quantity:   
KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E24, E28, E30, E34 Location: Front
Type: Track, Stage 3
Bearing: PTFE-lined pillow-ball, no bushing

KMAC Stage 3 camber/caster plates are designed for track or race-only situations where comfort and noise are not the primary concerns. The Stage 3 camber plates use a pillowball bearing, solidly mounted within the camber plate for direct alignment of the strut shaft and no excess play or deflection. Stage 3 are designed to increase negative camber with their patented 'floating' adjustment that changes camber and caster together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Fitment is limited to race-only small diameter coil-over springs (not stock-type). Bearing inserts and adapters included. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1984-1991  E30 BMW  318i 318is 318ic 325e 325es 325i 325ic 325is M3
1982-1988  E28 BMW  528e 533i 535i 535is M5
1993-1995  E34 BMW  525i
1982-1989  E24 BMW  633csi 635csi M6
KMAC
Part #: 193316-3L
Price: $545.00 (USD) 
Ships on Jul 9, 2018
Free Shipping Free Shipping
Quantity: