Oiling System for BMW 5 Series E34 (1987-1995)

Genuine BMW Set Oil-Filter Element
This item fits the following BMW Chassis:
E12, E28, E34, E24, E23, E32

Fits BMW Engines including:
M30,S38

The intermediate shaft bearings are located in the engine block (an inner and outer bearing). The intermediate shaft is driven from the timing belt and spins the oil pump shaft. Whenever the engine is torn down and the block is chemically or thermally cleaned these bearings will need to be replaced. The bearings must be sized with the intermediate shaft! The bearing surfaces must be machined to the correct tolerance for the block and shaft! You must make your engine builder aware of this before final assembly.

Note: these bearings must be machined for the shaft and block.

M20 block uses inner and outer bearings but the bearings are the same part numbers.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!

The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.

K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top-tier product for your European vehicle.

Features:

• Consistent filtering across entire filter surface
• Superior ASTMF316 filtration performance
• Magnetic Prefiltering
• Progressive rate bypass combined with high flow characteristics of the filter media avoids unfiltered oil bypassing the filter during cold startup and high rpm
• Easy inspection of engine contamination
• Proven in Motorsports, Military and Aerospace applications for years. Technology is FAA approved for use in aircraft. 

At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.

This part fits the following BMWs:
1991 - 1999 E36 Coupe 323i 325is 328i
1993 - 1999 E36 Convertible 323i 325i 328i
1990 - 1999 E36 Sedan 325i 328i 
1989 - 1995 E34 525i, 530i, 
1998 - 2004 E39 Touring 525i 528i 
1996 - 2004 E39 Sedan 525i 528i 530i 
1999 - 2001 E46 Convertible 323ci 325ci 330ci
2002-2006 E46 Convertible 325ci 330ci
1998 - 2001 E46 323ci 325ci 330ci M3
2002 - 2006 E46 325ci 330ci
1998 - 2001 E46 Touring 323i 325i
2002 - 2006 E46 Touring 325i 325xi
1998 - 2001 E46 Sedan 323i 325i 328i 330i
2002 - 2006 E46 Sedan 325i 325xi 330i 330xi
2000 - 2006 E53 X5 SUV X5 X5 3.0i 

Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!

The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.

K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top-tier product for your European vehicle.

Features:

• Consistent filtering across entire filter surface
• Superior ASTMF316 filtration performance
• 7 times the flow of comparable paper oil filters
• Magnetic Prefiltering
• Progressive rate bypass combined with high flow characteristics of the filter media avoids unfiltered oil bypassing the filter during cold startup and high rpm
• No more cutting apart messy paper filters for trapped debris inspection
• Proven in Motorsports, Military and Aerospace applications for years. Technology is FAA approved for use in aircraft. 

At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.

Watch to learn how to clean a K&P oil filter

This product fits the following BMWs:
1975-1983 E21 320i
1982-1991 E30 325i
1982-1988 E28 528i 528e
1989-1995 E34 525i