BMW Brakes & Brake Parts for BMW 5 Series E34 (1987-1995)

Brake pad wear sensor should be replaced at ever brake service, even if not worn down. This ensures the sensor is as new as possible and less likely to fail due to built up corrosion.

Fits the following BMWs:
E31 850Ci - Rear
E32 735i/iL 740i/iL 750iL - Front and Rear
E34 525i 535i 530i 540i M5 - Front and Rear

The latest in the Yellow line takes all of the RSL29 characteristics and adds a bit more aggressive behavior. Friction levels go up for more initial bite and better fade resistance. Modulation and release stays close to RSL29 levels. Pad and rotor wear is a little more than on the previous Yellows but still within reasonable levels and the RSL1 is still considered an extended endurance pad. Its development stemming from GT classes at Le Mans and Nürburgring.

Since Pagid pads tend to "out-gas" we recommend using these pads with a new gas-slotted or cross-drilled rotor for the best performance. Pagid brake pads are not compatible with previously used rotors, especially if used with a carbon or Kevlar based race pad.

This item fits the following BMWs:
1995-1998 E36 BMW M3 
2001-2006 E46 BMW 330i M3 
1989-1995 E34 BMW 525i 530i 535i 540i M5 
1988-1994 E32 BMW 735i 735il 740i 740il 750il 
1997-2002 Z3 BMW M Roadster M Coupe
2006-2008 Z4 BMW M Roadster M Coupe

BMW E34 Z26 Street Warrior Brake Kit - Front and Rear provides superior braking performance and enhanced brake cooling. This comprehensive kit from Turner Motorsport includes everything needed for a complete brake upgrade.

• Drilled and Slotted Rotors: Designed for improved cooling and performance.
• Extreme Carbon-Fiber Ceramic Brake Pads: Offer severe-duty stopping power with minimal dust and reduced brake noise for a quieter drive.
• Stainless Steel Hardware: Ensures durability and long-lasting performance.
• New Guide-Pin Bushings: Provides smooth and reliable braking operation.
• High Temperature Brake Lubricant: Enhances braking efficiency and longevity.

The Extreme Carbon-Fiber Ceramic brake pads deliver exceptional stopping power without compromising daily drivability. The rotors are precision-drilled and slotted to enhance cooling and maintain optimal braking performance. Coated with Silver Zinc Dichromate plating, they resist rust and corrosion, extending their lifespan and maintaining their appearance.

 A complete set offered to ensure that the proper lifting techniques are at use. It's never wise to work under a vehicle supported by only a floor jack, with this complete kit you get a complete matching set to get the job done safe and fast.

• Special low profile thick frame side plates and reinforced lift arm for added strength and use.
• Wide track front wheels help provide chassis torsion control and durability.
• Angular positioned pump pistons provide maximum effective pump stroke even when jack is completely under the vehicle.
• Ball bearing mounted rear swivel caster wheels for easy maneuverability.
• Side mounted handles for carrying and easy positioning.
• Overload and bypass safety valve prevents jack overload and over extension.
• Two piece quick release padded handle for storage or transport.
• Dual piston's for 5 pump full extension

Details:

• Jack Capacity 2 Ton
• Max Lift Height 20"
• Low Height 3.25"
• Chassis Length 26.5"
• Overall Width 13"
• Saddle Diameter 4.5"
• Handle Lenght 50"
• Shipping Weight 50 lbs

Schwaben 12" wheel Stands:

These stands are made from special EPS foam with an anti-skid coating.

Won't scratch or mark your floors!

Lightweight at only 5 lbs each, makes these stands easy to carry and maneuver.

Works on virtually any surface, including sand!

Will not scoot, slip or slide, no matter the surface.

Specs:

12" tall,15.75" long,12" wide.

Works on wheel diameters from 25 to 30 inches.

BMW Brembo Type 3 Slotted Rotor Re-Ring Kit - 355x32mm is an essential upgrade for maintaining the peak performance of your Brembo brake system. This re-ring kit, available through Turner Motorsport, includes new rotor rings and rotor hat hardware kits specifically designed for Type 3 slotted 355x32mm Brembo brake kits, ensuring that your braking system remains efficient and responsive.

The BMW Brembo Type 3 Slotted Rotor Re-Ring Kit is engineered to provide optimal braking performance by enhancing heat dissipation and reducing brake fade. The Type 3 slotted design offers superior bite and consistent braking, even under the most demanding conditions, making it perfect for both track enthusiasts and spirited street drivers. By replacing the rotor rings with this high-quality kit, you maintain the integrity of your brake system without the need to purchase an entirely new rotor assembly.

This kit is designed to be a direct fit for Brembo brake kits, making installation straightforward and hassle-free. With Turner Motorsport’s commitment to quality, you can trust that this re-ring kit will provide reliable performance and longevity.

• Optimal braking performance: Enhances heat dissipation and reduces brake fade for consistent stopping power.
• High-quality replacement: Includes new rotor rings and rotor hat hardware for Brembo Type 3 slotted 355x32mm brake kits.
• Direct fit: Designed for easy installation with no modifications required.
• Cost-effective maintenance: Replaces worn rotor rings, preserving your brake system’s efficiency without needing a full rotor replacement.
• Track-ready performance: Superior bite and consistent braking under demanding conditions.