Packaged by Turner for BMW E36 (1992-1998) M3

Maintaining proper oil levels in your engine is crucial for peak performance. Undetected leaks can cause your oil to drop to dangerously low levels between oil changes, leading to severe engine damage.

One common culprit for oil leaks is the valve cover. Over time, exposure to extreme temperature fluctuations can wear down the gaskets, causing them to fail. Prevent oil leaks and protect your engine by replacing these vital components.

Comprehensive Kit Includes:

Valve Cover Perimeter Gasket Valve Cover Spark Plug Tube Gaskets 15 Rubber Grommets/Sealing Washers Ultra-Black RTV Gasket Maker Replace your old gaskets with our high-quality kit to keep your engine running smoothly and efficiently.

E46 M3 CSL brakes fit the E36 M3 for a bolt-on size enhancement and more stopping power. The CSL rotors are a full 30mm (1.18") larger than the stock E36 M3 discs. The larger rotor puts out more braking torque and can handle more friction and heat than stock. With the special brackets these larger rotors are able to bolt-on to the E36 M3 hub using your original calipers and lines. Simply bolt them on using the new caliper bracket. The E36 M3 CSL upgrade is a moderate upgrade over stock compared to a StopTech or Brembo Big Brake Kit but has lower upfront cost, lower consumable cost (pads and rotors), and has a wide range of pad choices (any brake pad for an E36 M3 or E46 M3 will work).

We offer these brakes with three rotor choices -

• Stoptech (Centric) CSL/ZCP Cross-Drilled and Floating
• Original M3 CSL/ZCP Cross-Drilled and Floating
• ECS 2-piece Cross Drilled and Slotted Floating (pictured)

With more braking torque, the brake bias is changed. For the street, you will notice more stopping power and more "bite" from the front brakes. You may not notice the front brakes are working harder. If you're using this kit on the track it will be more important to balance the brake bias using different front-rear pad compounds. The front brakes will be doing more work than before to slow the car down and you will need to balance that with a more aggressive pad on the rear. You may notice the front tires locking up sooner, especially in wet conditions. Contact us to discuss track pads for your situation.

Wheel fitment: 18" wheels are strongly recommended for brake clearance although some 17" wheels will work (if they clear a BBK they will work with these)

Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles. This kit includes Pentosin ATF-1, the transmission filter, gasket and bolts. 

Kit Includes:

• Automatic transmission filter with associated hardware
• Oil pan gasket
• Drain plug with sealing washer
• Fill plug with sealing washer
• 5 liters Pentosin ATF-1 automatic transmission fluid

This item fits the following BMWs: 
1995-1999  E36 BMW M3 
1991-1995  E34 BMW  530i

When installing a new clutch, it is important to replace old hardware and common wear items. This ensures both a smooth and reliable installation. This also allows you to perform maintenance while everything is apart as opposed to a needing to make future repairs when everything is back together.

Included in this kit:

• Genuine BMW hardware with the exception of flywheel bolts which are an original equipment supplier
• 2 Genuine BMW E46 M3 transmission mounts
• Genuine BMW clutch fork pivot pin
• Original Equipment Supplier driveshaft washer gasket
• MTC universal flex disc (AKA Guibo) with hardware
• MTC driveshaft center carrier
• FAG pilot bearing
• Victor Reinz rear main seal

Fits the following BMWs:
E36 BMW M3 S50/52

This kit is contains all new strut and shock mounts and hardware needed when installing a aftermarket suspension on your vehicle.

Click here for spring options  

Fits the following BMW's

1996-1999 BMW M3

This strut and shock mount package covers the front and rear rubber mounts and bushings commonly replaced during a strut and shock install. While you're installing new front struts and rear shocks these are easily installed - there's no additional labor and special tools are not required. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.

We sell the basic strut and shock mount package, which includes:

• Front strut mounts (also known as guide support)
• Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)
• Front strut tower paper washer gaskets
• Front and rear self-locking mounting nuts
• Rear Lifetime Warranty 'Repair Shop' shock mounts
• Rear shock mount reinforcements (to prevent cracking of shock towers)
• Rear shock mount gaskets

In addition, you can add the front spring pads, front bump stops, front dust boots, rear bump stops, and rear dust boots if needed. But please note that some shocks and coil overs come with all or some of these pieces already. If in doubt, check with your supplier on what is included.

We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!

This item fits the following BMWs:
1996-1999 E36 BMW M3
1996-2002 Z3 BMW 2.5 2.5i 2.8 3.0i M Coupe

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 3 kit replaces:

Control Arms & Bushings
Outer Tie Rods
Sway Bar End Links
Strut Tower Reinforcement Plate
Strut Mount & Gasket

The fan that attaches to the water pump carries so much rotational mass that it can actually hinder the performance of your engine. To address this, we now offer out line of fan delete kits that replace everything needed to get rid of your fan and fan clutch, without causing cooling issues as a result. This Ultimate kit is the top tier option, including the essential conversion components, the upgraded aluminum thermostat housing, and a brand new accessory belt.

This kit is best for someone who has not performed recent cooling system maintenance or who wants to replace everything at once for increased reliability and longevity.

Included in this kit:

• 80* thermostat
• 1 liter of coolant
• Water Wetter coolant additive
• Low-temperature coolant temperature sensor/switch
• Aluminum thermostat housing with gaskets
• Fan delete nut
• ECS  Aluminum Water Pump Pulley - Black
• Accessory Belt

Fits the following BMWs:
1992-09/1995 E36 BMW 325i/is/ic 328i/is/ic M3

**This kit is intended to be used with cars that have a functional auxiliary fan (64508364093) or an upgraded electrical fan installed.**

The fan that attaches to the water pump carries so much rotational mass that it can actually hinder the performance of your engine. To address this, we now offer out line of fan delete kits that replace everything needed to get rid of your fan and fan clutch, without causing cooling issues as a result. This Comprehensive kit is the mid-priced option, including the essentials and an upgraded aluminum thermostat housing that won't crack or break like the brittle plastic housing. 

This kit is best for someone who wants to upgrade their thermostat housing to aluminum, has already upgraded their water pump pulley, and has performed regular maintenance on their engine drive belts.

Included in this kit:

• 80* thermostat
• 1 liter of coolant
• Water Wetter coolant additive
• Low-temperature coolant temperature sensor/switch
• Aluminum thermostat housing with gaskets
• Fan delete nut

Fits the following BMWs:
09/1995-1999 E36 BMW 323is/ic 328i/is/ic M3

**This kit is intended to be used with cars that have a functional auxiliary fan (64508364093) or an upgraded electrical fan installed.**