BMW Brakes & Brake Parts for BMW E60 M5 S85 5.0L

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

This caliper bushing kit will eliminate flex caused by weak rubber caliper bushings. As the brake pedal is pressed the caliper grabs the rotor and twists on its mounting bushings. The rubber bushings allow the caliper to deflect and twist which affects pedal feel and results in uneven pad wear. These solid brass bushings will not twist or deflect so your calipers can squeeze the pads evenly on both sides of the rotor (sort of like what multi-piston big brakes do). This will give you much longer pad life and a more consistent pedal feel. This is the most complete kit we have ever sold with stainless steel caliper slide bolts, o-rings, and new dust boots. Unlike other kits, these bushings are pressed into the caliper and will not shift or slide on their own.

Installation is straightforward: remove the old rubber bushings and press in the new brass bushings (we recommend special tool 003326ECS03). High temp caliper grease or anti-seize is required. The new bushings include an inner o-ring that helps trap grease on the slide bolt, reducing friction and wear.

***Click here for installation instructions*** 

***Click here for the installation tool***

For most models with floating calipers. Fits the rear of E90/2 and E60, but for the front you'll need the kit found here. Does not fit E30 models with Girling calipers, but is compatible with Ate calipers. 

These 2-piece floating rotors help dissipate heat better than a standard cast iron rotor and are also lighter for less unsprung weight. Managing heat in the brake system is vital to braking performance, especially on the track or when driven hard. It's why your brake rotors have internal vanes that vent heat as the rotor spins. These 2-piece ECS rotors feature an outer cast iron friction surface ring that is separate from the aluminum center hat. This allows better airflow through the vanes and for the friction ring can expand as it gets hot. The rotors are also cross-drilled for better ventilation and slotted to improve brake pad performance.

ECS 2-Piece Rotors feature:

• Aluminum hats for light weight
• Heat-treated cast iron friction rings
• 2-piece assembly improves brake cooling
• Anti-corrosion coating on non-friction surfaces and hard anodizing on rotor hat

These are the same size as the stock rotors so your stock caliper and mounting bracket will fit and there will be no clearance issues with your wheels or to other components. Stainless steel rotor retaining screws are included. You can use these with any brake pad.

Price is for the pair of brake rotors.

This item fits the following BMWs:
2006-2010 E60 BMW M5
2006-2010 E63 E64 BMW M6