BMW Engine Parts for BMW 5 Series E60 (2004-2010)

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

These WPC-treated bearings are the best we have seen! WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are original equipment KS bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

This item fits the following BMWs: 
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix 
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1982-1988 E28 BMW 528e
1989-1995 E34 BMW 525i
1997-2003 E39 BMW 525i 528i 530i
2004-2005 E60 BMW 525i 530i 
2004-2006 E83 BMW X3 2.5i X3 3.0i 
2000-2006 E53 BMW X5 3.0i 
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i 

BMW N52 3.0L, N55 3.0L Timing Chain Tensioner With Guard Rail

Ensure proper engine performance and prevent catastrophic damage with the BMW N52 3.0L, N55 3.0L Timing Chain Tensioner With Guard Rail. This essential component maintains tension on the timing chain, preventing slack that can lead to skipped teeth and engine failure.

Benefits:

• Maintains proper tension on the timing chain
• Prevents skipped teeth and potential engine damage
• Includes guard rail for added protection
• Quiets noisy timing chains

Keep your BMW engine running smoothly and reliably with the BMW N52 3.0L, N55 3.0L Timing Chain Tensioner With Guard Rail.

This Valvetronic variable valve timing actuator is designed to optimize engine performance by adjusting the eccentric shaft, effectively increasing or decreasing valve lift and duration as needed. By dynamically controlling valve timing, it enhances power delivery, fuel efficiency, and overall driving performance.

A failing actuator can lead to noticeable power loss, reduced performance, and an illuminated check engine light. Restore your BMW's performance with this premium replacement from Bremmen Parts, designed to meet or exceed OE specifications.

Features:

Exact Fitment: Engineered to perfectly match your BMW’s specifications for seamless installation. Durable Construction: Built with high-strength materials to resist engine heat, vibration, and wear. Precision Manufacturing: Designed to OE dimensions for accurate clearances and alignment. Optimal Performance: Restores proper timing and functionality at all engine speeds. Get your BMW back on the road with reliable performance and confidence.

Discover the ultimate solution for your MINI Cooper's N12, N14, N16, and N18 engines in the R56 chassis – our MINI Cooper Front Crankshaft Seal Installer. This tool simplifies the installation process effortlessly. Just follow these easy steps: Tighten the three inner bolts to attach the inner piece onto the front crankshaft. Then, insert the seal into the outer portion of the tool. Place the outer portion over the now-attached stud and utilize the included pushing nut to apply uniform pressure, securely seating the seal onto the front crankshaft.

Crafted from robust materials, this tool is indispensable for both mechanics and DIY enthusiasts. Say farewell to laborious manual installations and welcome a quick, precise solution into your automotive toolkit. Upgrade your equipment today and make perfect seal installations a breeze.

This tool will also work on select BMW engines, please check fitment by entering your vehicle information!