BMW Tools & Specialty Equipment for BMW 6 Series E63 (2004-2010)

*Features a total lift height of almost 29 inches!*

Looking for the best of the best in your search for a floor jack? AC Hydraulic's DK13HLQ Hydraulic Floor Jack is the answer. This jack is built to take anything you can throw at it and keep on going. Using a wide and robust high-strength steel frame, blue powedercoat paint protection, and built-in safety overload valve, this jack was designed in mind to outlast us all!

Features:

• Very low minimum height of only 3.15 in
• Wide and robust frame made of high-strength steel
• Fitted with quick-lift pedal for easy reach of lifting point
• Precise and safe control whilst lowering
• Manual dead man’s release for optimum safety when lowering
• Built-in safety overload valve
• Noiseless wheels incorporating a polyurethane central O ring offers maximum surface protection
• Ergonomically designed handle ensuring positive and safe operation

Specifications:

• Capacity:  2900 lb 
• Min. height:  3.15 in 
• Max. height:  28.94 in 
• Frame length:  37.01 in 
• Handle length:  37.40 in 
• Frame height:  6.30 in 
• Width:  18.90 in 
• Weight:  86 lb

Due to clearance issues, many types of lifts require specific adapters that are made for reaching SUV and truck jack points. This 12-piece kit has been made by using stackable adapters that mount inside the lifting block trays so that vehicles with high ground-clearance or those with unique jack point locations are better accommodated. These adapters offer up to 7.2" of additional height when all combined.

Complete kit includes:

• Low‐profile round polyurethane contact pads  -  Qty: 4
• Sliding receivers that accommodate the round polyurethane contact pads and/or the stackable adapters  -  Qty: 4
• 3" stackable adapters.  -  Qty: 4

Fits BL-5000SLX/EXT and BL-7000SLX/EXT Series Only.

Looking for the best of the best in your search for a floor jack? AC Hydraulic's DK20Q Hydraulic Floor Jack is the answer. This jack is built to take anything you can throw at it and keep on going. Using a wide and robust high-strength steel frame, blue powedercoat paint protection, and built-in safety overload valve, this jack was designed in mind to outlast us all!

Features:

• Very low minimum height of only 3.15 inches
• Wide and robust frame made of high-strength steel
• Precise and safe control whilst lowering
• Manual dead man’s release for optimum safety when lowering
• Built-in safety overload valve
• Noiseless wheels incorporating a polyurethane central O ring offers maximum surface protection
• Ergonomically designed handle ensuring positive and safe operation
• DK20Q is fitted with quick-lift pedal for easy reach of lifting point

Specifications:

• Capacity:  4400 lbs
• Min. height:  3.15 inches
• Max. height:  19.49 inches
• Frame length:  25.98 inches 
• Handle length:  37.40 inches
• Frame height:  6.30 inches 
• Width:  16.14 inches
• Weight:  68 lbs

• Tough and rigid expanded polystyrene foam (EPS) with a load rating of 1,500lbs per wheel (almost twice what the normal corner weight would be on a 3-series BMW)
• 10" height X 12" width with minimal compression under load
• Light weight with each block weighing less than 6lbs and with a handy strap for carrying or hanging
• Curved cradle for the tire to sit inside
• Non-skid surface that won't scratch your floor

Looking for an alternative to your jack stands? With these wheel blocks you won't have to think twice about a jack stand scratching or denting the underside of your floor or the car falling off the jack stand. These work best when used with a floor jack under the subframe and the opposite axle wheels chocked. These are also a light weight and inexpensive alternative to the super-pricey plastic and metal ramps. They are resistant to most fluids and chemicals (but not solvents) and will never rust unlike metal ramps and blocks.

Also available in a 12" height.

BMW E60 M5 Crank Case Test Cap

The BMW E60 M5 Crank Case Test Cap is designed to facilitate accurate testing of crankcase pressure across a range of vehicle models. This versatile test cap is compatible with early and late model vehicles equipped with steel, aluminum, or plastic valve covers. Featuring a multi-diameter fitting, it connects directly to IMIBs, handheld manometers, and smoke machines, eliminating the need for adapters and ensuring precise readings without leaks.

Benefits:

• Versatile Compatibility: Suitable for use with steel, aluminum, and plastic valve covers on early and late model vehicles.
• Direct Connection: Multi-diameter fitting allows direct connection to IMIBs, handheld manometers, and smoke machines.
• Leak Prevention: Eliminates the need for adapters, reducing the risk of leaks and inaccurate readings.
• Enhanced Accuracy: Provides reliable crankcase pressure testing for better diagnostic results.