BMW Engine Parts for BMW 6 Series E63 (2004-2010)

Replace your cracked or warped valve cover with an OE BMW valve cover for perfect fitment.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Cylinder Head Cover - Cyl. 1-4
This item fits the following BMW Chassis:
E53 48IS,E53 X5,E63,E65,E70 X5 X5

Fits BMW Engines including:
N62,N62N

Has your BMW's with the N62 V8 engine developed a coolant leak at the front of the engine from the timing cover weep hole? If so the it is likely that the coolant transfer pipe seal, located below the intake manifold has developed a leak. Normally, replacing the seal on this pipe would require almost 40 hours of labor and involve removing the entire engine from the car, then removing the cylinder heads, and timing covers. With this new collapsible pipe this repair can be accomplished in under 10 hours! This solution will save you or your mechanic from a bunch of headaches and get your V8 back on the road leak free!

With more than 100 years in the industry, Elring is one of the oldest names in the European autoparts segment. Delivering OE-quality you can rest assured the job will be done right the first time. 

video: N62 Cooling Pipe Replacement

Supplement Gasket Kit Parts List

(click to expand)

BMW p/nQtyDescription

115317100481Rear Engine Block O-ring,

115175077171Heat Pipe w O-ring

115175085351Water Pump Gasket

115114399761Valley Pan Pipe Pump

111475072781Valley Pan w Gasket

116175211812Intake Manifold Gasket

071199035962Camshaft Adjuster O-ring

123114399881Alternator Feed Pipe

750il gasket kit deletes 11617521181 and 07119903596 and adds - 8 - 11617537999 profile gaskets

This item fits the following BMWs:
2004-2010 E60 BMW 545i 550i
2004-2010 E63 BMW 645ci 650i
2002-2008 E65 BMW 745i 745li 750i 750li
2004-2006 E53 BMW X5 4.4i X5 4.8is
2007-2013 E70 BMW X5 4.8i xDrive48i

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!

The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.

K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top-tier product for your European vehicle.

Features:

• Consistent filtering across entire filter surface
• Superior ASTMF316 filtration performance
• Magnetic Prefiltering
• Progressive rate bypass combined with high flow characteristics of the filter media avoids unfiltered oil bypassing the filter during cold startup and high rpm
• Easy inspection of engine contamination
• Proven in Motorsports, Military and Aerospace applications for years. Technology is FAA approved for use in aircraft. 

At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.

Watch to learn how to clean a K&P oil filter

This part fits the following BMWs:
2006 - 2010 E60 M5 Sedan
2006 - 2010 E63 M6 Coupe & Convertible
2008 - 2013 E90 M3 Sedan
2008 - 2013 E92 M3 Coupe
2008 - 2013 E93 M3 Convertible