BMW 6 Series E64 (2004-2010)

Upgrade to wheel studs from bolts for an enhanced connection and easier wheel installation. Racing entities often require wheel studs for better wheel-to-hub contact, offering improved confidence during high-speed performance. Turner Motorsport's wheel studs are designed to accommodate various spacer widths effortlessly, simplifying the setup process. Discover why this switch from bolts to studs can make a significant difference:

• Simplifies spacer usage with a single application designed for various spacer widths
• Wheel studs act as a wheel hanger, easing wheel installation
• Reduces constant wheel bolt removal, minimizing wear on wheel hubs
• Facilitates quick and easy tire changes as the studs stay in the hub
• Recommended torque of 15Nm with thread-locking compound during installation
• Compatible with spacers up to 20mm in size

The oxygen sensor is vital to the performance and drivability of your car. The engine computer relies on data from the sensor to make adjustments in engine efficiency and performance. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today. There is no lifespan on O2 sensors but there are several fault codes that indicate a failed sensor (O2 monitoring, cat efficiency, O2 heating circuit, O2 readiness, and others). The O2 sensor is heated and has a self-calibration feature so once you get the codes or feel performance has suffered, a new sensor is a good starting point to get you back to peak performance.

This is a Bosch O2 sensor - also known as a Lambda probe. Bosch is an OEM supplier to BMW.

Position: after the catalytic converter (post-cat).

This item fits the following BMWs:
2008-2013 E90 E92 E93 BMW M3 Sedan, Coupe, Convertible

The fuel pump is held into the tank with a retaining lock ring. Most people would take an extension or punch and tap out the ring with a hammer. But that's the wrong way to do it. You could damage the lock ring, or worse, the tank itself. This handy tool is toothed to match the lock ring and takes a standard 1/2 drive ratchet or small extension. Twist the ratchet and the lock ring comes un-done cleanly and smoothly. A hefty tool that pays for itself over and over. Fits most BMWs from 1988-2013. Also has application for MINI and Porsche.

This metal screw ring tightens down to old the top of the fuel pump or fuel filter assembly dependent on model of vehicle.

Together they make this job simple and easy and ensure a tight fit with a new ring. 

BMW M60 M62 Engine Spark Plugs - Set Of Eight (Platinum+4) are the perfect solution to restore the performance of your BMW's engine. These high-quality Platinum+4 spark plugs are designed to provide a strong and consistent spark, improving idle, fuel efficiency, and overall engine performance. Worn spark plugs can cause poor idling, low fuel economy, and engine misfires, but replacing them with these Platinum+4 plugs ensures a more powerful spark and reduces carbon buildup, enhancing engine efficiency.

For optimal performance, it's recommended to replace all serviceable ignition components, including spark plugs and coil packs. Doing so will ensure your ignition system operates at peak efficiency, improving power and fuel economy.

• Platinum+4 design provides a strong, consistent spark
• Improves idle, fuel efficiency, and overall engine performance
• Reduces carbon buildup for better engine efficiency
• Helps prevent engine misfires and low fuel economy
• Ideal for replacing all ignition components for optimal results

The oxygen sensor is vital to the performance and drivability of your car. The engine computer relies on data from the sensor to make adjustments in engine efficiency and performance. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today. There is no lifespan on O2 sensors but there are several fault codes that indicate a failed sensor (O2 monitoring, cat efficiency, O2 heating circuit, O2 readiness, and others). The O2 sensor is heated and has a self-calibration feature so once you get the codes or feel performance has suffered, a new sensor is a good starting point to get you back to peak performance.

This is a Bosch O2 sensor - also known as a Lambda probe. Bosch is an OEM supplier to BMW.

Position: bank 1, before the catalytic converter (pre-cat).

This item fits the following BMWs:
2006-2010 E60 BMW M5
2006-2010 E63 E64 BMW M6

The oxygen sensor is vital to the performance and drivability of your car. The engine computer relies on data from the sensor to make adjustments in engine efficiency and performance. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today. There is no lifespan on O2 sensors but there are several fault codes that indicate a failed sensor (O2 monitoring, cat efficiency, O2 heating circuit, O2 readiness, and others). The O2 sensor is heated and has a self-calibration feature so once you get the codes or feel performance has suffered, a new sensor is a good starting point to get you back to peak performance.

This is a Bosch O2 sensor - also known as a Lambda probe. Bosch is an OEM supplier to BMW.

Position: post-cat, after the catalytic converter (pre-cat). Bank 1 and Bank 2 use the same sensor (2 required per vehicle).

This item fits the following BMWs:
2006-2010 E60 BMW M5
2006-2010 E63 E64 BMW M6

Rod bearings should be replaced as a preventative measure before 80,000 miles. This package is the most complete rod bearing overhaul kit available and includes not just the latest BMW rod bearings and connecting rod bolts, but also everything else that should be replaced with the oil pan and front subframe off the car.

Rod bearings continue to be a sore subject among M3, M5, and M6 owners. The rod bearings in the S85 V10 have been known to fail within 60,000 miles. There could be a number of reasons for premature failure with a lot of finger-pointing as to the real cause. Whatever the reason, rod bearings are wearing out sooner than expected and their replacement should be considered a required preventative maintenance item. We suggest a replacement interval of between 60,000-80,000 miles with frequent engine oil analysis done along the way*. Driving moderately and allowing the engine to warm up before hard use will also extend rod bearing life.

After doing so many rod bearing replacements in our own service shop we have put together this comprehensive overhaul package. Our package includes -

Genuine BMW rod bearings
- 11247841703, upper bearings - latest design from BMW (either original or WPC treated**)
- 11247841702, upper bearings - latest design from BMW (either original or WPC treated**)
- 11247834522, connecting rod bolts
- Red Line engine assembly lube

Oil Pan
- 11137836361, oil pan gasket
- 07119905485, oil pan screws (required by BMW)
- 07129905600, oil pan screws (required by BMW)
- 11137836568, oil pan screws
- 07119963129, seal washers
- 11417836233, auxiliary oil pump gaskets
- 11121304174, oil pickup tube o-ring

Replacing the rod bearings requires mechanical knowledge and skill, a clean workspace, and several specialist tools. Our preferred procedure is to leave the engine in the car but remove the front subframe. The engine must be supported from above with an engine brace. Removing the front subframe involves disconnecting the control arms and steering rack and steering column. The oil pan can then be removed and you can access the connecting rods and bearings. Replacing the rod bearings themselves is straightforward but patience and forethought will be extremely helpful. In addition to analyzing the severity of the rod bearing wear, the crankshaft must also be inspected closely for damage. Rod bearings that have been severely worn may have damaged the crankshaft (requiring replacement or machining).

* BMW released an updated rod bearing around 2011 that uses different materials than the original design. The old rod bearings were constructed with several layers or metal, including copper and lead. If an engine oil analysis revealed high levels of these specific metals then it was a sure sign that the rod bearings were nearing replacement. However, the new BMW bearings do not use copper or lead so an oil analysis will not alert you to heavy bearing wear. The new bearings are also a harder material which prolonged the life of the bearing but increased the liklihood of crankshaft damage if a bearing failed. Even though the bearing theoretically lasts longer it's even more important to preventativly replace them before they damage the crankshaft.

** These WPC-treated bearings are the best we have seen for the S85. WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are factory BMW bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

***BE Bearings is another top pick when considering which bearing kit to choose. Working with Clevite, an OE bearing supplier, their design allows for a bit more clearance than stock, allowing better oil circulation and reducing friction. The material is also made from the original bearing composition of lead-copper, not the updated tin-aluminum used in factory BMW bearings which was excessively hard, potentially damaging the crankshaft when high friction occurred. This softer metal composition can also be tested for via oil analysis, allowing you to see high bearing wear, something the tin-aluminum bearings don't give you the ability to do.

Internal VANOS Pressure Line
One of the VANOS oil lines runs along the inside of the timing chain cover and into the oil pan. It can only be replaced with the oil pan removed. If you have sluggish performance or VANOS fault codes this is one of the common causes and now is the perfect time to replace it. If it fails down the line the oil pan will have to be removed again.

Front Subframe Hardware
Our preferred procedure for accessing the engine block is by disconnecting the control arms and steering rack and then removing the front subframe altogether. This hardware is not required but may be a good idea, especially if your original subframe bolts are rusty. Hardware includes:
31106760222, front subframe mounting bolts
31106770256, front subframe mounting bolts
33326760668, front wishbone collar nut

Tie Rod Boots
32106765782, tie rod boot kit

Motor Mounts with Hardware
22116762607, left motor mount
22116762608, right motor mount
07129904088, motor mount bolts
07129904865, motor mount nuts

Engine Oil Change
Liqui Moly GT1 10w-60 engine oil
11427840594, OEM oil filter.

This package fits the following BMWs:
2006-2010 E60 BMW M5
2006-2011 E63 BMW M6

This OEM Bosch in-tank fuel pump includes the pump and inlet strainer. This can be replaced easily by accessing the top of the fuel tank beneath the rear seat, no need to drop the fuel tank.

This part does not include the fuel level sensor. The fuel level sensor can be reused from the original fuel pump or a new sensor can be purchased under T#392738.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs: 

E39 BMW 525i 528i 530i 

E60 BMW 525i 525xi 528i 528i xDrive 530i 530xi 535i 535xi 545i 550i 

E63 BMW 645Ci 650i

Knock sensors detect pings in the engine and adjust ignition timing to restore perfect operation. Faulty knock sensors will throw engine codes or even lead to engine damage. Replace your sensor with a reliable, high quality Bosch sensor to ensure proper engine ignition timing.

Bosch # 13627568421 OEM replacement for BMW part # 13627568421, 12141709317, and 12141435502.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

The external temperature sensor on a BMW is placed within the underbody plastics that extend very close to the road. As a result it's easy to damage by rolling into a low curb or parking lot tire stop. The first sign you may have a problem with your external temperature sensor is if you have a really low reading. This is caused by the sensor either being damaged, missing or having an open circuit; the wires leading to the sensor may have torn off in an impact.

Includes solder filled heat shrink connectors, contact leads with wire, plug housing, temperature sensor, 10 pack of zip ties, and a panel mount zip tie for mounting the sensor.

Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication! 

Liqui Moly GmbH develops and tests all engine oils, additives, and car care products in-house, ensuring all Liqui Moly products extend the life of your engine via optimal lubrication. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world. Turner Motorsport trusts Liqui Moly to keep all of our race cars - including the M6 - running smooth from the first hotlap to the last.

Turner Motorsport recommends Synthoil Race Tech GT1 10w-60 for your S85 engine. Race Tech is a modern high performance engine oil formulated for engines that experience extreme load pressures. Fully synthetic, the oil combines base oils and additives to provide exceptional lubrication and engine wear protection. This oil provides immediate lubrication upon cold start, offering significantly improved protection compared to other oils. Liqui Moly Race Tech GT1 10w-60 will keep your S85 pulling hard and running smooth on your commute home from work, your touge run through the valley, and while you are trying to get your best times on the track. 

Choose the level of Liqui Moly Oil Service your BMW deserves: 

• Liqui Moly Bronze service involves switching to Liqui Moly oil without the introduction of additives.
• Liqui Moly Silver service includes a Pro-Line Engine Flush to remove sludge and carbon buildup from the oil circulation system.
• Liqui Moly Gold service includes Silver service and Jectron Fuel Injection System Cleaner. This cleans your injectors and maintains your fuel system to improves engine performance and efficiency.
• Liqui Moly Platinum service includes Gold service and Cera Tec Oil Additive. This prevents wear and reduces friction to improve engine performance and efficiency.

Below you can add new drain plug and crush washer, along with your choice of oil filter.

This kit also features many Popular Service Tools that make your life easier when working on your BMW:

• Turner Motorsport Magnetic Fender Cover
• Schwaben 6.5L Fluid Extractor
• Schwaben 14mm/17mm Service Wrench
• Schwaben Professional BMW/MINI Scan Tool

Have you ever been bent over your engine bay for a few hours and noticed that your belt scratched your fender? We've got you covered with the Turner Motorsport Magnetic Fender Cover. We also offer a myriad of Schwaben tools. Schwaben's Professional Scan Tool vastly simplifies diagnosing your BMW. This scan tool offers OE-level diagnostics for over 25 years of models, also allowing you to access common service features like resetting your oil service light, installing a new battery, throttle body adjustment, DPF regeneration, and more. The Schwaben Fluid extractor allows you displace 6.5L of fluid without making a mess of your workspace. Lastly, we've found that the 14mm/17mm service wrench allows you to service most of your vehicle with just one tool - one of the biggest hangups with working on a vehicle is losing your tools. Save yourself time looking for multiple different tools across your garage by owning one that does it all.

These products fit the following BMWs:

2005-2010 E60/E61 M5
2005-2010 E63/E64 M6