BMW X Series E70 (2007-2013)

Clear BMW chassis

Please ensure your correct model is selected

Sub-Categories

Sort By:

Automatic Transmission Service Kit - Level 2 - BMW GA6HP19Z Transmiss...
For vehicles equipped with automatic transmission GA6HP19Z *** Check Transmission Type Prior To Orde
Packaged by Turner - Corporate Logo
T#:5376301
Part#: 24117571217TMSKT
In Stock
Sale - Save 10% $ 175.99

This product was last offered at the strikethrough price on
05-03-2026

$ 157.62 USD
Free Shipping
Sale - Save 10%
$ 175.99

This product was last offered at the strikethrough price on
05-03-2026

$ 157.62 USD
Free Shipping
Includes all the necessary components for a complete transmission service with Liqui Moly fluid Over the life of a vehicle, the transmission can often be overlooked when performing routine maintenance. If left unserviced, the automatic transmission fluid will break down, causing the valve body and filter to become contaminated with deposits and sludge. This will lead to poor shifting, slipping, and ultimately, transmission failure. Kit Includes: Automatic transmission oil pan with integrated filter Oil pan gasket Drain plug with sealing washer Fill plug with sealing washer 7 quarts Liqui Moly automatic transmission fluid
Show More Show Less
Packaged by Turner - Corporate Logo
T#:5376276
Part#: 11427953129TKT
In Stock
$ 115.99

This product was last offered at the strikethrough price on
05-15-2026

$ 103.99 USD
Free Shipping
$ 103.99 USD
Free Shipping
This new generation oil is made with a quality synthetic base and includes a molecular friction modifier for reduced friction and wear. It also glows under UV light so leaks can be easily traced! This unique oil contains a fluorescent green chemical friction modifier to smooth out hard metal surfaces, reducing overall engine wear and heat due to friction. Tests have shown a reduction in friction coefficient of as much as 15%! MolyGen oil is also a great choice for modern turbocharged engines which produce much more heat. This kit from Turner Motorsport contains all that you will need to do your regular service on your vehicle. The kit contains: Seven Quarts of Liqui Moly MolyGen Engine Oil Oil Filter Kit New Drain Plug with Crush Washer UV Flashlight Make your next service a quality one with this new kit from Turner Motorsport
Show More Show Less
Automatic Transmission Service Kit
For GA8HP70Z or GA8HP45Z automatic transmissions
For GA8HP70Z or GA8HP45Z automatic transmissions
Packaged by Turner - Corporate Logo
T#:5389733
Part#: 24118612901TMSKT
In Stock
Sale - Save 23% $ 215.99

This product was last offered at the strikethrough price on
05-03-2026

$ 166.09 USD
Free Shipping
Sale - Save 23%
$ 215.99

This product was last offered at the strikethrough price on
05-03-2026

$ 166.09 USD
Free Shipping
Over the life of a vehicle, the transmission can often be overlooked when performing routine maintenance. If left unserviced, the automatic transmission fluid will break down, causing the valve body and filter to become contaminated with deposits and sludge. This will lead to poor shifting, slipping, and ultimately, transmission failure. Kit Includes: Automatic transmission filter with associated hardware Oil pan gasket Drain plug with sealing washer Fill plug with sealing washer 7 Liters of Liqui Moly Top Tec ATF 1800 Turner Motorsport recommends performing a full service on your automatic transmission every 60,000 miles
Show More Show Less

Packaged by Turner - Corporate Logo
T#:599759
Part#: 11377603979KT2
In Stock
Sale - Save 10% $ 268.99

This product was last offered at the strikethrough price on
05-03-2026

$ 241.95 USD
Free Shipping
Sale - Save 10%
$ 268.99

This product was last offered at the strikethrough price on
05-03-2026

$ 241.95 USD
Free Shipping
Includes actuator, actuator gasket and valve cover gaskets

Packaged by Turner - Corporate Logo
T#:637846
Part#: 1142753729312KT1
In Stock
$ 97.99 USD
Free Shipping
$ 97.99 USD
Free Shipping
Over time gaskets become dry and brittle allowing oil to leak in your engine compartment. Replace this gasket and stop having to top off your oil every month. A common source of leaks on the N54/55 is the gaskets between the the thermostat plate and filter housing, and also the filter housing to engine block.
Show More Show Less
Vargas Turbo Technologies - Corporate Logo
T#:557934
Part#: VTT-S55-CBC
In Stock
$ 129.99 USD
Free Shipping
$ 129.99 USD
Free Shipping
The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Packaged by Turner - Corporate Logo
T#:555453
Part#: LMOCK28KT
In Stock
$ 123.99

This product was last offered at the strikethrough price on
05-15-2026

$ 111.99 USD
Free Shipping
$ 111.99 USD
Free Shipping
Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication! Select your vehicle to make sure you are viewing the best Liqui Moly options for your application. Includes: 7 Liters of Liqui Moly MolyGen 5w-40 Engine Oil Liqui Moly UV Flashlight Hengst Oil Filter Kit Febi Oil Drain Plug & Washer Liqui Moly Molygen New Generation fully synthetic engine oil is carefully engineered, starting with a high quality synthetic base. What separates Molygen from other engine oils is the molecular friction modifier for reduced friction and wear. Because of this, Molygen glows fluorescent green under UV light, allowing you to easily find any leaks! The fluorescent green chemical friction modifier smooths out hard metal surfaces, reducing overall engine wear and heat due to friction. Tests have shown to reduce the friction coefficient by 15%! MolyGen oil is also a great choice for modern forced induction engines which produce much more heat. BMWs are notorious for leaking oil. Make chasing your leak easier with Liqui Moly Molygen New Generation engine oil. (Once you find it, give us a call - we can help you stop that leak, too!) Smooth engine running characteristics Long engine service life due to exceptional protection against wear Rapid oil delivery at low temperatures Optimum oil pressure at all engine speeds Premium lubrication reliability at high and low temperatures High shear and ageing stability Reduces fuel consumption and pollutant emissions Outstanding engine cleanliness Tested with catalytic converters and performance proven with turbochargers Miscible and compatible with commercially-available engine oils Approved for the following specifications: ACEA C3 API SN / CF VAG 502.00 / 505.00 BMW Longlife-01 Liqui-Moly is a German chemical company that offers top of the line engine oils, additives, and car care products that are designed to extend the life of your engine and ensure the best lubrication and cleanliness off engine and transmission components possible. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui-Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world.
Show More Show Less
VTT “OBD-LOCK” ODB Port Locking Tool
For Vehicles Produced After 1995
Vargas Turbo Technologies - Corporate Logo
T#:26938503
Part#: VTT-OBD-LOCK
In Stock
$ 97.99 USD
Free Shipping
$ 97.99 USD
Free Shipping
VTT is proud to offer our “OBD-LOCK” OBD port locking tool. This is tool is made from billet 6061-T6 aluminum and is designed to completely lock out your OBD port from being accessed. This is useful for people who do not want dealers, techs, etc from accessing their OBD port, and possibly changing a tune, etc. This is also perfect for anti-theft prevention as it will not allow a would-be thief to hook up to the car’s OBD port, duplicate a key, etc. The OBD-LOCK cannot be removed without physically destroying the OBD port if you do not have the proper tools. VTT uses 5 types of screw head designs for every 200 OBD-LOCKS made. This means that worldwide only 40 OBD-LOCKS are using the same head design. For each batch of 200, we redesign the screw heads meaning every batch of 200 OBD-LOCKS will use different screw heads and tools. Each OBD-LOCK sent has its head design chosen at random. After Extensive testing, we have found that our OBD lock fits EVERY SINGLE OBD port we have tried, this means it will fit every single OBD port currently on the market from a high-end BMW to a Ford F150 diesel.
Show More Show Less

Vargas Turbo Technologies - Corporate Logo
T#:558084
Part#: VTT-CRANK-BREATH
In Stock
$ 129.99 USD
Free Shipping
$ 129.99 USD
Free Shipping

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Show More Show Less

Packaged by Turner - Corporate Logo
T#:583536
Part#: N52PISKT
In Stock
Sale - Save 20% $ 243.99

This product was last offered at the strikethrough price on
05-03-2026

$ 194.75 USD
Free Shipping
Sale - Save 20%
$ 243.99

This product was last offered at the strikethrough price on
05-03-2026

$ 194.75 USD
Free Shipping

Every 60-80,000 miles, we recommend replacing your spark plugs to ensure your ignition system is running optimally. Over time carbon can build up around the head of the spark plug and decrease spark strength and effectiveness, leading to weaker fuel mixture detonation, misfires, and potential check engine lights. To prevent this, have put together our High-Performance Ignition Service Kits. These kits include new Bav Auto High-Performance Ignition Coils, new spark plugs, dielectric grease, and a BMW spark plug service label to keep track of when your spark plugs were replaced.

Bav Auto's Ignition coils feature core windings that have been modified to increase firepower and promote a faster, more efficient burn. This gives your BMW/MINI increased torque in the lower range of RPM and more horsepower in the upper range. Exact improvements depend on the current condition of your engine, but you'll definitely feel the difference. They'll also improve your fuel economy.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Show More Show Less
Packaged by Turner - Corporate Logo
T#:5376273
Part#: N55OCIKT
In Stock
$ 120.99 USD
Free Shipping
$ 120.99 USD
Free Shipping
To keep your driving machine in top shape, regular maintenance is imperative. BMW's service interval for an oil change varies based on driving habits. We recommend changing your oil after no more than 10,000 miles. A 5,000 oil service interval is preferred for aggressive or city driving. Includes seven quarts of BMW synthetic engine oil, Hengst oil filter This kit contains Seven Liters of BMW Synthetic Engine Oil Engine Oil Filter Oil Drain Plug Gasket (Included with filter kit)
Show More Show Less
Packaged by Turner - Corporate Logo
T#:5403247
Part#: 11132210959TMSKT
In Stock
Sale - Save 3% $ 81.99

This product was last offered at the strikethrough price on
05-03-2026

$ 79.23 USD
Free Shipping
Sale - Save 3%
$ 81.99

This product was last offered at the strikethrough price on
05-03-2026

$ 79.23 USD
Free Shipping
Gasket between oil pan and engine block. A common piece to begin leaking on any engine, oil pan gaskets begin to leak after a few years.


Packaged by Turner - Corporate Logo
T#:578658
Part#: 65816905133-1KT
In Stock
Sale - Save 23% $ 96.85

This product was last offered at the strikethrough price on
05-03-2026

$ 74.70 USD
Free Shipping
Sale - Save 23%
$ 96.85

This product was last offered at the strikethrough price on
05-03-2026

$ 74.70 USD
Free Shipping
Onboard computer not reading accurate ambient temperatures anymore? This kit includes everything you need to restore external temp monitoring to your BMW.
Packaged by Turner - Corporate Logo
T#:402850
Part#: N63LMOCP1
In Stock
Starting at $ 167.96 USD
Free Shipping
Starting at $ 167.96 USD
Free Shipping

Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication! 

Liqui Moly GmbH develops and tests all engine oils, additives, and car care products in-house, ensuring all Liqui Moly products extend the life of your engine via optimal lubrication. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world. Turner Motorsport trusts Liqui Moly to keep all of our race cars - including the M6 - running smooth from the first hotlap to the last.

Turner Motorsport Recommends three Liqui Moly oil options for your BMW:

Leichtlauf High Tech full synthetic engine oil is designed to provide the highest amount of engine protection as well as fuel savings and reduced oil consumption - most BMWs like to drink oil, Leichtlauf should make yours less thirsty. Using proprietary blends of base oils and the latest additive technology, this oil will ensure smooth running gasoline and diesel engines in both high and low temperatures. Other amazing benefits include: optimum oil pressure at all speeds, rapid oil delivery at low oil temperatures, high shear and aging stability, turbo, multi-valve, and supercharger compatibility, and long service life.

Synthoil Premium engine oil is designed to provide great engine wear protection as well as fuel savings and reduced oil consumption. Using proprietary blends of base oils and the latest additive technology, this full synthetic oil will ensure smooth running gasoline and diesel engines in both high and low temperatures.

New generation Molygen engine oil allows you to easily identify oil leaks with the included UV flashlight - BMWs are notorious for oil leaks, and this allows you to work towards solving this problem. Additionally, Molygen is a fully synthetic oil designed to provide the highest amount of engine protection as well as fuel savings and reduced oil consumption possible. 

Choose the level of Liqui Moly Oil Service your BMW deserves: 

  • Liqui Moly Bronze service involves switching to Liqui Moly oil without the introduction of additives.
  • Liqui Moly Silver service includes a Pro-Line Engine Flush to remove sludge and carbon buildup from the oil circulation system.
  • Liqui Moly Gold service includes Silver service and Jectron Fuel Injection System Cleaner. This cleans your injectors and maintains your fuel system to improves engine performance and efficiency.
  • Liqui Moly Platinum service includes Gold service and Cera Tec Oil Additive. This prevents wear and reduces friction to improve engine performance and efficiency.

Below you can add new drain plug and crush washer, along with your choice of oil filter.

This kit also features many Popular Service Tools that make your life easier when working on your BMW:

  • Turner Motorsport Magnetic Fender Cover
  • Schwaben 6.5L Fluid Extractor
  • Schwaben 14mm/17mm Service Wrench
  • Schwaben Professional BMW/MINI Scan Tool

Have you ever been bent over your engine bay for a few hours and noticed that your belt scratched your fender? We've got you covered with the Turner Motorsport Magnetic Fender Cover. We also offer a myriad of Schwaben tools. Schwaben's Professional Scan Tool vastly simplifies diagnosing your BMW. This scan tool offers OE-level diagnostics for over 25 years of models, also allowing you to access common service features like resetting your oil service light, installing a new battery, throttle body adjustment, DPF regeneration, and more. The Schwaben Fluid extractor allows you displace 6.5L of fluid without making a mess of your workspace. Lastly, we've found that the 14mm/17mm service wrench allows you to service most of your vehicle with just one tool - one of the biggest hangups with working on a vehicle is losing your tools. Save yourself time looking for multiple different tools across your garage by owning one that does it all.

These products fit the following BMWs:

2011– 2013 E70 X5 xDrive50i
2008– 2013 E71 X6 xDrive50i
2009+ F01/F02 750i 750Li sDrive/xDrive 750i 750Li sDrive/xDrive
2010– 2012 F07 550i GT sDrive/xDrive
2011+ F10/F11 550i sDrive/xDrive
2012+ F12/F13 650i sDrive/xDrive 650i sDrive/xDrive
2013– F07 550i GT sDrive/xDrive
2014– F15 X5 xDrive50i

 

Show More Show Less
Vargas Turbo Technologies - Corporate Logo
T#:558795
Part#: VTT-CRANKHUB-1
Ships in 3 Business Days
$ 889.99 USD
Free Shipping
$ 889.99 USD
Free Shipping
Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.
Show More Show Less

Packaged by Turner - Corporate Logo
T#:555446
Part#: LMOCK20KT
In Stock
$ 124.99

This product was last offered at the strikethrough price on
03-09-2026

$ 121.99 USD
Free Shipping
$ 121.99 USD
Free Shipping

Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication!   Select your vehicle to make sure you are viewing the best Liqui Moly options for your application. 

Includes:

  • 8 Liters of Liqui Moly Longtime High Tech 5w-30 Engine Oil 
  • Hengst Oil Filter Kit
  • Febi Drain Plug with Crush Washer

Longtime High Tech engine oil is designed to provide the highest amount of engine protection as well as fuel savings and reduced oil consumption possible. Using proprietary blends of base oils and the latest additive technology, this oil will ensure smooth running gasoline and diesel engines in both high and low temperatures. Other amazing benefits include: optimum oil pressure at all speeds, rapid oil delivery at low oil temperatures, high shear and aging stability, turbo and multi-valve compatibility, and long service life.

Properties:

  • Smooth engine running characteristics
  • Long engine service life due to exceptional protection against wear
  • Rapid oil delivery at low temperatures
  • Optimum oil pressure at all engine speeds
  • Premium lubrication reliability at high and low temperatures
  • High shear and ageing stability
  • Reduces fuel consumption and pollutant emissions
  • Outstanding engine cleanliness
  • Tested with catalytic converters and performance proven with turbochargers
  • Miscible and compatible with commercially-available engine oils

Approved for the following specifications:

  • ACEA C3
  • API SN / CF
  • BMW Longlife-04
  • MB-Approval 229.51
  • VAG 502.00 / 505.00

Recommended for the following specifications:

  • ACEA A3 / B4
  • MB 229.31
  • VAG 505.01

Liqui-Moly is a German chemical company that offers top of the line engine oils, additives, and car care products that are designed to extend the life of your engine and ensure the best lubrication and cleanliness off engine and transmission components possible. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui-Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world.

Show More Show Less

Vargas Turbo Technologies - Corporate Logo
T#:638889
Part#: VTT-CRANKGUARD
In Stock
Starting at $ 89.99 USD
Free Shipping
Starting at $ 89.99 USD
Free Shipping
It is a well-known issue on the BMW N54/55 platforms that your serpentine belt can fail for various reasons. When this happens, there is a high chance of the belt getting sucked behind the front damper pulley and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure. Even if you do not lose the engine, it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT, even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Vargas' seal is different from those already on market in two major ways. Firstly, it is not offensively priced. Secondly, it is 100% billet with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long-term corrosion resistance. Crank Seal Guard includes: One VTT Billet N54/55 Crank Seal Guard Two extended 12.9 Grade bolts, and two stainless washers We highly recommend you install WITH a crank bolt capture at the same time, as you have to remove the damper anyway. Then you will get the benefit of helping eliminate the dreaded spun crank hub and the crank seal issue
Show More Show Less
Packaged by Turner - Corporate Logo
T#:402866
Part#: S63LMOCP1
In Stock
Sale - Save 1% $ 122.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 122.13 USD
Free Shipping
Sale - Save 1%
$ 122.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 122.13 USD
Free Shipping

Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication! 

Liqui Moly GmbH develops and tests all engine oils, additives, and car care products in-house, ensuring all Liqui Moly products extend the life of your engine via optimal lubrication. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world. Turner Motorsport trusts Liqui Moly to keep all of our race cars - including the M6 - running smooth from the first hotlap to the last.

Turner Motorsport Recommends three Liqui Moly oil options for your BMW:

Leichtlauf High Tech full synthetic engine oil is designed to provide the highest amount of engine protection as well as fuel savings and reduced oil consumption - most BMWs like to drink oil, Leichtlauf should make yours less thirsty. Using proprietary blends of base oils and the latest additive technology, this oil will ensure smooth running gasoline and diesel engines in both high and low temperatures. Other amazing benefits include: optimum oil pressure at all speeds, rapid oil delivery at low oil temperatures, high shear and aging stability, turbo, multi-valve, and supercharger compatibility, and long service life.

Synthoil Premium engine oil is designed to provide great engine wear protection as well as fuel savings and reduced oil consumption. Using proprietary blends of base oils and the latest additive technology, this full synthetic oil will ensure smooth running gasoline and diesel engines in both high and low temperatures.

New generation Molygen engine oil allows you to easily identify oil leaks with the included UV flashlight - BMWs are notorious for oil leaks, and this allows you to work towards solving this problem. Additionally, Molygen is a fully synthetic oil designed to provide the highest amount of engine protection as well as fuel savings and reduced oil consumption possible. 

Choose the level of Liqui Moly Oil Service your BMW deserves: 

  • Liqui Moly Bronze service involves switching to Liqui Moly oil without the introduction of additives.
  • Liqui Moly Silver service includes a Pro-Line Engine Flush to remove sludge and carbon buildup from the oil circulation system.
  • Liqui Moly Gold service includes Silver service and Jectron Fuel Injection System Cleaner. This cleans your injectors and maintains your fuel system to improves engine performance and efficiency.
  • Liqui Moly Platinum service includes Gold service and Cera Tec Oil Additive. This prevents wear and reduces friction to improve engine performance and efficiency.

Below you can add new drain plug and crush washer, along with your choice of oil filter.

This kit also features many Popular Service Tools that make your life easier when working on your BMW:

  • Turner Motorsport Magnetic Fender Cover
  • Schwaben 6.5L Fluid Extractor
  • Schwaben 14mm/17mm Service Wrench
  • Schwaben Professional BMW/MINI Scan Tool

Have you ever been bent over your engine bay for a few hours and noticed that your belt scratched your fender? We've got you covered with the Turner Motorsport Magnetic Fender Cover. We also offer a myriad of Schwaben tools. Schwaben's Professional Scan Tool vastly simplifies diagnosing your BMW. This scan tool offers OE-level diagnostics for over 25 years of models, also allowing you to access common service features like resetting your oil service light, installing a new battery, throttle body adjustment, DPF regeneration, and more. The Schwaben Fluid extractor allows you displace 6.5L of fluid without making a mess of your workspace. Lastly, we've found that the 14mm/17mm service wrench allows you to service most of your vehicle with just one tool - one of the biggest hangups with working on a vehicle is losing your tools. Save yourself time looking for multiple different tools across your garage by owning one that does it all.

These products fit the following BMWs:
2010–2013 E70 X5 M
2010–2013 E71 X6 M
2011+ F10 M5
2012+ F12/13 M6
2013+ F06 M6 Gran Coupe
2015+ F85 X5 M
2015+ F86 X6 M

Show More Show Less

Packaged by Turner - Corporate Logo
T#:555429
Part#: LMOCK4KT
In Stock
$ 107.99 USD
Free Shipping
$ 107.99 USD
Free Shipping

Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication!   Select your vehicle to make sure you are viewing the best Liqui Moly options for your application. 

Includes:

  • 7 Liters of Longtime High Tech Engine Oil 5w-30
  • Hengst Engine Oil Filter
  • Oil Drain Plug & Gasket

Longtime High Tech engine oil is designed to provide the highest amount of engine protection as well as fuel savings and reduced oil consumption possible. Using proprietary blends of base oils and the latest additive technology, this oil will ensure smooth running gasoline and diesel engines in both high and low temperatures. Other amazing benefits include: optimum oil pressure at all speeds, rapid oil delivery at low oil temperatures, high shear and aging stability, turbo and multi-valve compatibility, and long service life.

Properties:

  • Smooth engine running characteristics
  • Long engine service life due to exceptional protection against wear
  • Rapid oil delivery at low temperatures
  • Optimum oil pressure at all engine speeds
  • Premium lubrication reliability at high and low temperatures
  • High shear and ageing stability
  • Reduces fuel consumption and pollutant emissions
  • Outstanding engine cleanliness
  • Tested with catalytic converters and performance proven with turbochargers
  • Miscible and compatible with commercially-available engine oils

Approved for the following specifications:

  • ACEA C3
  • API SN / CF
  • BMW Longlife-04
  • MB-Approval 229.51
  • VAG 502.00 / 505.00

Recommended for the following specifications:

  • ACEA A3 / B4
  • MB 229.31
  • VAG 505.01

Liqui-Moly is a German chemical company that offers top of the line engine oils, additives, and car care products that are designed to extend the life of your engine and ensure the best lubrication and cleanliness off engine and transmission components possible. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui-Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world.

Show More Show Less
Packaged by Turner - Corporate Logo
T#:5416764
Part#: 11377548388TMSKT
Ships on Aug 12, 2026
Sale - Save 19% $ 220.99

This product was last offered at the strikethrough price on
05-03-2026

$ 179.20 USD
Free Shipping
Sale - Save 19%
$ 220.99

This product was last offered at the strikethrough price on
05-03-2026

$ 179.20 USD
Free Shipping
Includes new Valvetronic motor, gasket, and hardware. The Valv-tronic adjuster unit changes the the timing shaft to adjust the valve timing.

Packaged by Turner - Corporate Logo
T#:5416756
Part#: 11747626350TMSKT
Ships in 1-2 days
Sale - Save 45% $ 408.99

This product was last offered at the strikethrough price on
07-14-2026

$ 223.48 USD
Free Shipping
Sale - Save 45%
$ 408.99

This product was last offered at the strikethrough price on
07-14-2026

$ 223.48 USD
Free Shipping
Kit includes both boost solenoids, vacuum hose and T fitting for a easy leak free install

Vargas Turbo Technologies - Corporate Logo
T#:7530036
Part#: COOLANTCAPBLUE
In Stock
$ 79.99 USD
Free Shipping
$ 79.99 USD
Free Shipping
VTT is proud to offer their billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. This coolant cap retains ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap. VTT also designed these caps to complement their N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap, so all 4 will have the same design. These caps are offered in 4 colors – Red, Black, Blue, and Clear anodized Replaces Genuine BMW Reservoir Cap # 17117639020 Note: Fitment includes 99% of all BMW with a coolant Reservoir tank from the E series forward, meaning then fit even the brand New G8X M3/4 with the S58, all B58, etc. If your BMW is an E90 or newer this cap most likely will fit
Show More Show Less
OEM Accessory Belt Service Kit - N52 3.0L
This is for vehicles without 4 zone auto climate control
Packaged by Turner - Corporate Logo
T#:593693
Part#: N52ABKT
In Stock
Sale - Save 18% $ 135.99

This product was last offered at the strikethrough price on
07-08-2026

$ 111.50 USD
Free Shipping
Sale - Save 18%
$ 135.99

This product was last offered at the strikethrough price on
07-08-2026

$ 111.50 USD
Free Shipping
Over time, accessory belts begin to wear out and crack. This can lead to the belt slipping, squeaking, or even snapping. Replace your belts and tensioners on a regular basis to ensure you don't end up stranded on the side of the road with a dead battery or overheated engine due to a bit of simple overlooked maintenance. This kit includes all of the items that will need replaced such as the belts, tensioners, and hardware.
Show More Show Less
Vargas Turbo Technologies - Corporate Logo
T#:18733532
Part#: VTT-CRANKHUB-6
Ships in 1 Business Day
$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD
Free Shipping
$ 939.99 USD
Free Shipping
Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.
Show More Show Less


Packaged by Turner - Corporate Logo
T#:180875
Part#: TMS180875
In Stock
$ 142.24

This product was last offered at the strikethrough price on
05-07-2026

$ 107.33 USD
Free Shipping
$ 107.33 USD
Free Shipping
Not only will this kit stop most E90 oil leaks, it's the perfect addition for ignition coil or spark plug replacement! Oil leaks - and the damage they can cause - seem to be the worst annoyances on these cars. The biggest source of an oil leak is from the valve cover, followed by the oil filter housing, Valvetronic seal, camshaft seals, and the eccentric shaft sensor seal. Once the oil leaks, and if ignored for an extended time, the oil will contaminate vital electrical sensors. This is especially the case with ignition coils and also the eccentric shaft sensor on the Valvetronic shaft at the top of the cylinder head. During any ignition coil and spark plug replacement take a close look inside for any oil pooling at the bottom. We have been seeing valve cover oil leaks as soon as 40,000 miles. We look for oil leaks on every E90 that comes into our shop.

We have put together this package of valve cover gaskets and other related gaskets and seals for you to fully overhaul the N52 valve cover and put a stop to those pesky oil leaks. This package has the replacement parts for N52 engines built from the 2007 model year and includes:

  • 11127582245 - N52 valve cover gasket set
  • 11127552280 - N52 eccentric shaft sensor seal
  • 11127559699 - N52 Valvetronic gasket

2007 and later N51/N52 engines do not need replacement valve cover bolts, unless the bolts are actually broken off or missing. Unlike the 2006 aluminum hardware, the later parts are steel and not 1-time use.

These are all OEM or OE parts. Replacement of these gaskets and seals is straight-forward but a long process. BMW dealers typically charge for over eight hours of labor. If you have replaced spark plugs before you should be capable of this repair. In addition, there are several other parts to replace while you're in the vicinity: camshaft sensor o-rings, oil filter housing profile gasket, VAN0S solenoids, and the eccentric shaft sensor. These other parts, except the eccentric shaft sensor (see below), are replaceable without removing the valve cover but are more easily accessed during the valve cover work.

Eccentric Shaft Sensor: This is the position sensor that relays the eccentric shaft's position back to the DME. It's located at the front of the engine and is only accessible with the valve cover off . The seal around the sensor can fail and allow oil to blow out from under the cam cover. Oil can then leak into the sensor itself and cause it to fail. Without a functioning sensor your E90 can experience poor running, hesitation, poor performance, jerky shifts, and sluggish response. It's easy to check and see if oil has accumulated inside the sensor: unbolt the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside or even around the sensor itself, plan on replacing this sensor during your next ignition coil, spark plug, and/or valve cover gasket work.

This valve cover kit fits the following BMWs:
2008-2012 E82 BMW 128i
2007-2011 E90 BMW 328i 328xi 328i xDrive - Sedan
2007-2012 E91 BMW 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2007-2010 E60 BMW 528i 528xi 528i xDrive
2011 F10 BMW 528i
2007-2010 E83 BMW X3 3.0i X3 3.0si
2007-2013 E70 BMW X5 3.0si
10/2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive30i
Show More Show Less
Spec-D Widened Fender Flares - E70 X5 (Non-M)
For models with 20" and 21" wheels only
Spec-D Tuning - Corporate Logo
T#:641914
Part#: FDF-X507BK-GL
Back Ordered
$ 220.00

This product was last offered at the strikethrough price on
02-09-2026

$ 201.99 USD
Free Shipping
$ 201.99 USD
Free Shipping
Give your E70 X5 the M Sport look by widening the stance with these Spec-D fender flares. Made of the same polypropylene as the OE equivalent Matte Black Finish Installation hardware included No cutting or trimming needed; some drilling may be required Kit contains total of four, two front and two rear, flares to cover all four corners.
Show More Show Less
Packaged by Turner - Corporate Logo
T#:555442
Part#: LMOCK16KT
In Stock
$ 115.99 USD
Free Shipping
$ 115.99 USD
Free Shipping

Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication!   Select your vehicle to make sure you are viewing the best Liqui Moly options for your application. 

Includes:

  • 8 Liters of Liqui Moly Special Tec LL Engine Oil 5w-30
  • Hengst Engine Oil Filter
  • Febi Oil Drain Plug & Gasket

Special Tec LL engine oil is designed to provide the highest amount of engine protection as well as fuel savings and reduced oil consumption possible. Using proprietary blends of base oils and the latest additive technology, this oil will ensure smooth engines in both high and low temperatures. Other amazing benefits include: optimum oil pressure at all speeds, rapid oil delivery at low oil temperatures, high shear and aging stability, and long service life.

Approved for:

  • BMW Longlife-01
  • VW 502 00
  • VW 505 00
  • MB-Freigabe 229.5

Liqui-Moly is a German chemical company that offers top of the line engine oils, additives, and car care products that are designed to extend the life of your engine and ensure the best lubrication and cleanliness off engine and transmission components possible. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui-Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world.

Show More Show Less

Packaged by Turner - Corporate Logo
T#:5376284
Part#: 11127570292TKT
In Stock
Sale - Save 5% $ 320.99

This product was last offered at the strikethrough price on
05-03-2026

$ 304.52 USD
Free Shipping
Sale - Save 5%
$ 320.99

This product was last offered at the strikethrough price on
05-03-2026

$ 304.52 USD
Free Shipping
If your valve cover has become cracked or warped, replace it with this Hamburg Tech cover from Turner Motorsport to prevent leaks and further valvetrain damage. Replace your leaking valve cover to keep your oil inside the engine, where it belongs. Includes everything needed to install a new valve cover: Valve cover Gasket flange Crank case vent hose Hardware
Show More Show Less

Vargas Turbo Technologies - Corporate Logo
T#:7530034
Part#: COOLANTCAPRED
Ships in 1 Business Day
$ 79.99 USD
Free Shipping
$ 79.99 USD
Free Shipping
VTT is proud to offer their billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. This coolant cap retains ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap. VTT also designed these caps to complement their N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap, so all 4 will have the same design. These caps are offered in 4 colors – Red, Black, Blue, and Clear anodized Replaces Genuine BMW Reservoir Cap # 17117639020 Note: Fitment includes 99% of all BMW with a coolant Reservoir tank from the E series forward, meaning then fit even the brand New G8X M3/4 with the S58, all B58, etc. If your BMW is an E90 or newer this cap most likely will fit
Show More Show Less
Packaged by Turner - Corporate Logo
T#:555449
Part#: LMOCK23KT
In Stock
$ 142.99

This product was last offered at the strikethrough price on
05-15-2026

$ 134.99 USD
Free Shipping
$ 134.99 USD
Free Shipping

Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication!   Select your vehicle to make sure you are viewing the best Liqui Moly options for your application. 

Includes:

7 Liters of Liqui Moly MolyGen 5w-40 Engine Oil
Liqui Moly UV Flashlight
Hengst Oil Filter Kit
ECS Tuning Magnetic Drain Plug & Washer

Liqui Moly Molygen New Generation fully synthetic engine oil is carefully engineered, starting with a high quality synthetic base. What separates Molygen from other engine oils is the molecular friction modifier for reduced friction and wear. Because of this, Molygen glows fluorescent green under UV light, allowing you to easily find any leaks!

The fluorescent green chemical friction modifier smooths out hard metal surfaces, reducing overall engine wear and heat due to friction. Tests have shown to reduce the friction coefficient by 15%!  MolyGen oil is also a great choice for modern forced induction engines which produce much more heat. BMWs are notorious for leaking oil. Make chasing your leak easier with Liqui Moly Molygen New Generation engine oil. (Once you find it, give us a call - we can help you stop that leak, too!)

Properties:

  • Smooth engine running characteristics
  • Long engine service life due to exceptional protection against wear
  • Rapid oil delivery at low temperatures
  • Optimum oil pressure at all engine speeds
  • Premium lubrication reliability at high and low temperatures
  • High shear and ageing stability
  • Reduces fuel consumption and pollutant emissions
  • Outstanding engine cleanliness
  • Tested with catalytic converters and performance proven with turbochargers
  • Miscible and compatible with commercially-available engine oils

Approved for the following specifications:

  • ACEA C3
  • API SN / CF
  • VAG 502.00 / 505.00
  • BMW Longlife-01

Liqui-Moly is a German chemical company that offers top of the line engine oils, additives, and car care products that are designed to extend the life of your engine and ensure the best lubrication and cleanliness off engine and transmission components possible. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui-Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world.

Show More Show Less

Packaged by Turner - Corporate Logo
T#:402692
Part#: N54LMOCP1
In Stock
Starting at $ 150.48 USD
Free Shipping
Starting at $ 150.48 USD
Free Shipping

Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication! 

Liqui Moly GmbH develops and tests all engine oils, additives, and car care products in-house, ensuring all Liqui Moly products extend the life of your engine via optimal lubrication. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world. Turner Motorsport trusts Liqui Moly to keep all of our race cars - including the M6 - running smooth from the first hotlap to the last.

Turner Motorsport Recommends three Liqui Moly oil options for your BMW:

Leichtlauf High Tech full synthetic engine oil is designed to provide the highest amount of engine protection as well as fuel savings and reduced oil consumption - most BMWs like to drink oil, Leichtlauf should make yours less thirsty. Using proprietary blends of base oils and the latest additive technology, this oil will ensure smooth running gasoline and diesel engines in both high and low temperatures. Other amazing benefits include: optimum oil pressure at all speeds, rapid oil delivery at low oil temperatures, high shear and aging stability, turbo, multi-valve, and supercharger compatibility, and long service life.

Synthoil Premium engine oil is designed to provide great engine wear protection as well as fuel savings and reduced oil consumption. Using proprietary blends of base oils and the latest additive technology, this full synthetic oil will ensure smooth running gasoline and diesel engines in both high and low temperatures.

New generation Molygen engine oil allows you to easily identify oil leaks with the included UV flashlight - BMWs are notorious for oil leaks, and this allows you to work towards solving this problem. Additionally, Molygen is a fully synthetic oil designed to provide the highest amount of engine protection as well as fuel savings and reduced oil consumption possible. 

Choose the level of Liqui Moly Oil Service your BMW deserves: 

  • Liqui Moly Bronze service involves switching to Liqui Moly oil without the introduction of additives.
  • Liqui Moly Silver service includes a Pro-Line Engine Flush to remove sludge and carbon buildup from the oil circulation system.
  • Liqui Moly Gold service includes Silver service and Jectron Fuel Injection System Cleaner. This cleans your injectors and maintains your fuel system to improves engine performance and efficiency.
  • Liqui Moly Platinum service includes Gold service and Cera Tec Oil Additive. This prevents wear and reduces friction to improve engine performance and efficiency.

Below you can add new drain plug and crush washer, along with your choice of oil filter.

This kit also features many Popular Service Tools that make your life easier when working on your BMW:

  • Turner Motorsport Magnetic Fender Cover
  • Schwaben 6.5L Fluid Extractor
  • Schwaben 14mm/17mm Service Wrench
  • Schwaben Professional BMW/MINI Scan Tool

Have you ever been bent over your engine bay for a few hours and noticed that your belt scratched your fender? We've got you covered with the Turner Motorsport Magnetic Fender Cover. We also offer a myriad of Schwaben tools. Schwaben's Professional Scan Tool vastly simplifies diagnosing your BMW. This scan tool offers OE-level diagnostics for over 25 years of models, also allowing you to access common service features like resetting your oil service light, installing a new battery, throttle body adjustment, DPF regeneration, and more. The Schwaben Fluid extractor allows you displace 6.5L of fluid without making a mess of your workspace. Lastly, we've found that the 14mm/17mm service wrench allows you to service most of your vehicle with just one tool - one of the biggest hangups with working on a vehicle is losing your tools. Save yourself time looking for multiple different tools across your garage by owning one that does it all.

These products fit the following BMWs:

2006-2012 E90 323i 325i 325xi 328i 328xi 330i 330xi 335i 335xi
2005-2009 E60/E61 525i 525xi 528i 528xi 530i 530xi 535i
2005-2008 E85/E86 Z4 2.5i Z4 3.0si
2010-2016 F10 520i 520Li 523i 525Li 528i
2009–2017 F10/F11/F07 535i
2009-2016 E89 Z4 sDrive18i Z4 sDrive20i Z4 sDrive23i 2008-2011 Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2005-2010 E83 X3 2.5si xDrive25i X3 3.0si 
2007-2013 E82/E88 125i 128i 135i 135is
2011 E82 1 Series M Coupe
2009-2011 E84 X1 X1 xDrive/sDrive20i xDrive25i X1 xDrive28i X1 xDrive/sDrive28i xDrive35i
2004-2010 E63/E64 630i
2006-2012 E87 130i
2010+ F25 X3 sDrive18i X3 xDrive20i X3 28i X3 xDrive28i X3 xDrive35i
2006-2013 E70 X5 3.0si xDrive30i X5 xDrive 35i
2008–2014 E71 X6 xDrive35i
2008–2015 F01 740i 740i/Li
2011–2015 F30/F31 335i
2011–2016 F30 320i 328i
2013–2016 F32/F33/F36 435i
2014+ F15 X5 xdrive 35i
2014+ F16 X6 xDrive35i
2014+ F26 X4 xDrive 35i X4 M40i
2011+ F06/F12/F13 640i
2012–2016 F20/F21 M135i
2012–2017 F20 125i
2013–2016 F22/F23 M235i
2014+ F22 220i 225i 228i
2016+ F87 M2
2013–2016 F34 320i GT
2013–2016 F34 328i GT
2014–2017 F26 X4 xDrive20i

Show More Show Less
Vargas Turbo Technologies - Corporate Logo
T#:5309605
Part#: VTT-COIL-N5X-BLU
In Stock
$ 169.99 USD
Free Shipping
$ 169.99 USD
Free Shipping
Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.
Show More Show Less

Packaged by Turner - Corporate Logo
T#:554062
Part#: 11517801063KT2
In Stock
Sale - Save 6% $ 187.99

This product was last offered at the strikethrough price on
05-03-2026

$ 176.63 USD
Free Shipping
Sale - Save 6%
$ 187.99

This product was last offered at the strikethrough price on
05-03-2026

$ 176.63 USD
Free Shipping

The water pumps BMW's should be serviced near 80,000 miles and may become an issue often times leaving the owner stranded. The aftermarket kit offered provides a single stop for water pump and thermostat replacement needs to save the search and get you back on the road.

Kit includes:

  • Facet thermostat
  • Graf water pump
  • Vaico coolant
  • Mounting hardware required for the water pump

 

This item fits the following BMWs: 
2009+ E90 BMW 335d 
2009+ E70 BMW X5 xDrive35d

Show More Show Less

Packaged by Turner - Corporate Logo
T#:554075
Part#: 11537601158KT2
In Stock
Sale - Save 24% $ 106.99

This product was last offered at the strikethrough price on
05-03-2026

$ 81.44 USD
Free Shipping
Sale - Save 24%
$ 106.99

This product was last offered at the strikethrough price on
05-03-2026

$ 81.44 USD
Free Shipping

If your vehicle is experiencing cooling issues, chances are the thermostat is the cause. Common symptoms include prolonged warm-up at highway speeds from the thermostat being stuck open, or consistent overheating issues from the thermostat being stuck in the closed position. Either condition can result in poor performance, and potential damage to vital components in your vehicle.

Kit includes

  • Wahler Thermostat
  • 1 liter of Coolant

This item fits the following BMWs: 
2008-2013  E82 BMW  135i 135is 1M Coupe 
2013+  E84 BMW  X1 xDrive35i 
2011  E90 BMW  335i 335xi 335i xDrive - Sedan 
2011-2013  E92 BMW  335i 335xi 335i xDrive - Coupe 
2011-2013  E93 BMW  335i Convertible 
2011-2013  E70 BMW  X5 xDrive35i 
2011-2013  E71 BMW  X6 xDrive35i

Show More Show Less
Packaged by Turner - Corporate Logo
T#:6181666
Part#: TWHF9905F13T
In Stock
Sale - Save 5% $ 151.99

This product was last offered at the strikethrough price on
05-15-2026

Starting at $ 144.57 USD
Free Shipping
Sale - Save 5%
$ 151.99

This product was last offered at the strikethrough price on
05-15-2026

Starting at $ 144.57 USD
Free Shipping
12.5MM (.49 inch) Big Pad Wheel Spacers for BMW E70 X5M, E71 X6/X6M, F02, F06, F07, F10, F12/F13, F22, F25, F3X, F8X M3/M4 These are our Big Pad wheel spacers designed for the latest generation of factory BMW wheels. The "wheel pad" is the back of the wheel that mounts to the hub on the car. Since the early 2000s the factory BMW wheel pad diameter has grown - 150mm, 152mm, 154mm, and now 156mm. Most of the wheel spacers on the market are 152mm. The difference from using the smaller spacer on a large pad will leave an unsightly step down between the back of the wheel and the brake rotor hat (see image). To fix this visual defect we use a larger diameter spacer - the Big Pad. This will have less of a step, or no step at all, when used with the larger pad size. Note that nearly all aftermarket wheel manufacturers use the smaller pad size (mainly to reduce unsprung weight). For more information on wheel pad sizes and their effects on fitment and strength, click to our spacers FAQ page. Wheel spacers are the ideal solution to resolve a number of fitment and aesthetic problems. A spacer fits between the wheel and the hub assembly. The wheel will be pushed further outboard by the thickness of the spacer. Spacers allow you to correct wheel offset issues when the wheel is too 'tucked in' to the bodywork, clear the wheel from contact with the suspension or inner bodywork, clear larger brakes, improve handling and stability by increasing track width, or simply to get the right look and stance. Our wheel spacers are compatible with almost any type of BMW wheel and are a direct fit to the wheel hub (see below for any fitment notes). Longer wheel bolts or wheel studs are required. This latest generation of the Turner Motorsport Wheel Spacers represent a total redesign of the wheel spacer concept - a ground-up, clean sheet design based on our years of BMW service and motorsports. We took everything we have learned from our service technicians, customers, and race team crew and built the spacer to beat all spacers. We've been in the BMW wheel spacer business probably longer than anybody and when it came time to make our own spacers, a basic spacer design just wouldn't do. We had to make a spacer that is lightweight (for lower unsprung mass), has a tough and durable coating to last through our New England winters, is easily removed (your mechanic will thank you), and is precisely engineered and manufactured for a proper fit on the hub and in the wheel. You won't find a better engineered wheel spacer on the market! Turner Wheel Spacer Features hub-centric design with hub-centric lip precise tolerance fitment thanks to CAD process and CNC mill machine large pad surface area - 156mm vs standard 150mm aerospace grade aluminum lightweight but very strong with high resistance to corrosion additional military-spec hardcoat for further corrosion resistance innovative Quick Release pockets for easy removal (better than a chamfered back edge) laser engraved size and part number for easy identification stealthy anthracite or black color Turner Motorsport track and street tested! Made in the USA Wheel Spacer Tech & FAQ Important Note: It is vital that you measure the depth of your hub lip. The depth of the lip must not exceed the thickness of the spacer. This is critical on newer chassis cars that have deeper hubs than older models. For examples and tips on measuring, check out our How To Measure for Spacers page. Wheel Spacer Encyclopedia - everything you wanted to know Spacer Specs bolt pattern: 5 x 120 center bore: 72.6mm hubcentric: yes wheel pad size: large Extended Wheel Bolts Required for all BMW wheel spacers is a set of longer wheel bolts or wheel studs. Spacers cannot be used with stock bolts. Our extended lug bolts are very high quality and high-grade steel lug bolt (grade 10.9). A black zinc coating will maintain a factory BMW appearance and provide long-lasting corrosion protection. Zinc finishes are designed to withstand 700 hours of salt spray testing. This item fits the following BMWs: Front or Rear 2014+ F22 BMW 228i 228iX M235i M235iX 2012+ F30 BMW 320i 320iX 328i 328iX 335i 335iX - Sedan 2012+ F31 BMW 328i 328iX - Wagon 2014+ F34 BMW 328i 328iX 335iX - Gran Turismo 2014+ F32 BMW 428i 428iX 435i 435iX - Coupe 2014+ F33 BMW 428i 428iX 435i 435iX - Convertible 2014+ F36 BMW 428i 428iX 435i 435iX - Gran Coupe 2015+ F80 BMW M3 2015+ F82 BMW M4 2010+ F07 BMW 535i GT, 535i xDrive GT, 550i GT, 550i xDrive GT 2011+ F10 BMW 528i 528i xDrive 535i 535i xDrive 535d 535d xDrive 550i 550i xDrive M5 2012+ F12 BMW 640i 640i xDrive 650i 650i xDrive M6 2013+ F06 BMW 640i Gran Coupe 640i xDrive Gran Coupe 650i Gran Coupe 650i xDrive Gran Coupe M6 Gran Coupe 2009+ F01 BMW 740i 740li 750i 750li 750i xDrive 750li xDrive 760li 2011+ F25 BMW X3 xDrive28i X3 xDrive35i Rear Only 2007-2013 E70 BMW 2007-2014 E71 BMW
Show More Show Less
Packaged by Turner - Corporate Logo
T#:556726
Part#: N63TISKT
In Stock
$ 332.99 USD
Free Shipping
$ 332.99 USD
Free Shipping

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

Show More Show Less


Vargas Turbo Technologies - Corporate Logo
T#:5309610
Part#: VTT-COIL-N5X-RED
Ships in 10 Business Days
$ 169.99 USD
Free Shipping
$ 169.99 USD
Free Shipping
Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.
Show More Show Less
Packaged by Turner - Corporate Logo
T#:1241340
Part#: 24118612901T3KT
Back Ordered
$ 480.99

This product was last offered at the strikethrough price on
06-19-2026

$ 480.00 USD
Free Shipping
$ 480.00 USD
Free Shipping
Over the life of a vehicle, the transmission can often be overlooked when performing routine maintenance. If left unserviced, the automatic transmission fluid will break down, causing the valve body and filter to become contaminated with deposits and sludge. This will lead to poor shifting, slipping, and ultimately, transmission failure. For your 8-speed transmission, BMW recommends replacing your entire transmission pan and filter as the stock pan is constructed of plastic. This plastic pan will experience numerous drastic heat cycles over its lifetime, causing it to become weak and brittle, leading to potential catastrophic failure. Not only is this dangerous, but this is also very expensive when factoring in regular services. Upgrade your BMW's ZF transmission pan to PPE's Heavy-Duty Aluminum Transmission Pan and be done with pan replacements! PPE's one-of-a-kind transmission oil pan is cast from high-strength aluminum, allowing this pan to be used for the life of your transmission while also providing multiple benefits over your stock pan. Thanks to the thicker aluminum construction, internal heat fins, and integrated external cool fins, this pan helps promote reduced transmission fluid temperatures. PPE's trans pan has also been designed to allow for an additional quart of transmission fluid. The combined benefits of both cooler trans fluid and greater fluid capacity results in better lubrication, increased service life, and longer track sessions!
Show More Show Less
Packaged by Turner - Corporate Logo
T#:556734
Part#: N55TISKT
In Stock
$ 275.99 USD
Free Shipping
$ 275.99 USD
Free Shipping

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

Show More Show Less

Packaged by Turner - Corporate Logo
T#:555448
Part#: LMOCK22
In Stock
$ 116.99 USD
Free Shipping
$ 116.99 USD
Free Shipping

Liqui Moly is an official sponsor of Turner Motorsport. We work closely with Liqui Moly to ensure your BMW is receiving optimal lubrication!   Select your vehicle to make sure you are viewing the best Liqui Moly options for your application.

Includes:

7 Liters of Liqui Moly 0w-40 Voll-Synthese Energy Oil
Hengst Oil Filter Kit
Febi Oil Drain Plug & Washer

Liqui-Moly's Voll-Synthese Energy engine oil is specifically formulated for optimum oil penetration speed, deposit prevention, and resistance to aging. These factors allow for exceptional gasoline or diesel engine cleanliness, keeping the surfaces of the engine and engine components free from carbon and sludge deposits. This allows the oil to form a stronger film that in turn helps prevent wear much more efficiently than many standard oils. This also allows for easy, smooth engine operation that results in better responsiveness and less total fuel consumption.

Meets the following requirements;

  • ACEA A3-98/B3-98
  • API SJ-CF
  • BMW [Longlife] LL-98
  • Daimler (MB 229.1)
  • VW 502.00 - 505.00

Liqui-Moly is a German chemical company that offers top of the line engine oils, additives, and car care products that are designed to extend the life of your engine and ensure the best lubrication and cleanliness off engine and transmission components possible. With more than 50 years of experience and reviews across the world from magazines and race teams, Liqui-Moly proves time and time again why they are one of the most innovative lead forces of performance automotive chemicals in the world.

Show More Show Less

Packaged by Turner - Corporate Logo
T#:5498500
Part#: 12137594937IGKT
In Stock at Vendor
$ 336.94 USD
Free Shipping
$ 336.94 USD
Free Shipping
If your BMW's mileage is getting up there, be sure to keep your ignition system in check. Whether you currently have a misfire or you're just doing preventative maintenance, this kit is perfect. The kit includes: 6 Delphi Coils with locks 6 Bosch spark plugs BMW spark plug service label for your records 1 packet of American Grease Stick dielectric grease The kit includes: 6 Bremi Coils with locks 6 Bosch spark plugs BMW spark plug service label for your records 1 packet of American Grease Stick dielectric grease
Show More Show Less
Oil Pan Gasket Replacement Kit
For vehicles with automatic transmission only
Packaged by Turner - Corporate Logo
T#:5403285
Part#: 11137548031TMSKT
In Stock
Sale - Save 1% $ 194.99

This product was last offered at the strikethrough price on
02-16-2026

$ 192.19 USD
Free Shipping
Sale - Save 1%
$ 194.99

This product was last offered at the strikethrough price on
02-16-2026

$ 192.19 USD
Free Shipping
Includes new pan gasket, hardware and a oil service kit. A common piece to begin leaking on any engine, oil pan gaskets begin to leak after a few years.

Packaged by Turner - Corporate Logo
T#:6091465
Part#: 11515A05704APKT
Ships on Dec 2, 2026
Sale - Save 15% $ 620.99

This product was last offered at the strikethrough price on
04-01-2026

$ 526.79 USD
Free Shipping
Sale - Save 15%
$ 620.99

This product was last offered at the strikethrough price on
04-01-2026

$ 526.79 USD
Free Shipping
If your water pump is starting to fail, you may notice coolant leaks, or even hear a whining noise coming from under the hood. If you think your water pump is starting to fail, replace it as soon as you can. The main downside to an electric water pump is you may also notice nothing - nothing but overheating! Keep your eyes peeled for warning signs it may be time to replace your water pump. N54 and N55 engines are prone to water pump failure - replace every 60,000 miles. Comes with electric water pump and installation hardware. Aluminum mounting bolts are one time use. Replace every time the water pump is removed.
Show More Show Less
Vargas Turbo Technologies - Corporate Logo
T#:7292018
Part#: TISTUD201425
Back Ordered
Starting at $ 335.99 USD
Free Shipping
Starting at $ 335.99 USD
Free Shipping
VTT is proud to offer Titanium wheel stud kits for the vehicle owner looking for the lowest possible unsprung weight while maintaining high strength, and good looks. This kit is 60% lighter than factory steel studs and nuts with a total kit of 20 nuts, and studs being 3.1LBS. VTT kit details are as follows: Grade 5 Titanium studs, rated at more than 135,000PSI Tensile Strength Grade 5 Titanium nuts with 60-degree cone seat to fit most all aftermarket wheel applications M5 Hex for easy installation Three Colors Available – Raw, Black, Burnt M14x1.25x75mm on the small end to M14x1.5 on the long end. This will convert M14x1.25 cars into M14x1.5 pattern Installation notes: Apply locktite to the studs (short end) and torque to 20 ft/lb. Lug nuts should be torqued to factory specifications. For safety retorque all hardware (studs and nuts) after 25-50 miles.
Show More Show Less

Packaged by Turner - Corporate Logo
T#:554067
Part#: 11517531859KT4
In Stock
Sale - Save 8% $ 243.99

This product was last offered at the strikethrough price on
05-03-2026

$ 224.38 USD
Free Shipping
Sale - Save 8%
$ 243.99

This product was last offered at the strikethrough price on
05-03-2026

$ 224.38 USD
Free Shipping

The water pumps in BMW's should be serviced near 80,000 miles and may become an issue often times leaving the owner stranded. The aftermarket kit offered provides a single stop for water pump and thermostat replacement needs to save the search and get you back on the road.

Kit includes:

  • Mahle-Behr thermostat
  • Geba water pump
  • Vaico coolant
  • Mounting hardware required for the water pump


This item fits the following BMWs:
2006-2010 E60 BMW 550i
2006-2010 E63 BMW 650i
2005-2008 E65 BMW 750i 750li
2007-2013 E70 BMW X5 4.8i X5 xDrive48i

Show More Show Less

VTT Billet Coolant Reservoir Cap - Anodized Clear - Most BMWs 2006+ (...
This coolant cap retains ALL of the factory provisions by simply allowing you to snap t...
Vargas Turbo Technologies - Corporate Logo
T#:7530035
Part#: COOLANTCAPRAW
Ships in 3 Business Days
$ 78.99 USD
Free Shipping
$ 78.99 USD
Free Shipping
VTT is proud to offer their billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. This coolant cap retains ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap. VTT also designed these caps to complement their N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap, so all 4 will have the same design. These caps are offered in 4 colors – Red, Black, Blue, and Clear anodized Replaces Genuine BMW Reservoir Cap # 17117639020 Note: Fitment includes 99% of all BMW with a coolant Reservoir tank from the E series forward, meaning then fit even the brand New G8X M3/4 with the S58, all B58, etc. If your BMW is an E90 or newer this cap most likely will fit
Show More Show Less
Vargas Turbo Technologies - Corporate Logo
T#:5122267
Part#: VTTFILTERCAPBLUE
Ships in 4 Business Days
$ 89.99 USD
Free Shipping
$ 89.99 USD
Free Shipping
VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized
Show More Show Less
Vargas Turbo Technologies - Corporate Logo
T#:18733531
Part#: VTT-CRANKHUB-5
Ships in 10 Business Days
$ 880.99 USD
Free Shipping
$ 880.99 USD
Free Shipping
Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.
Show More Show Less


Active Autowerke - Corporate Logo
T#:397307
Part#: 12-032
Ships in 1 Business Day
$ 240.00 USD
Free Shipping
$ 240.00 USD
Free Shipping
Rotrex superchargers utilize a unique traction drive system that sets it apart from other centrifugal-style superchargers. For best performance, Rotrex recommends replacing this fluid every 50,000 miles. This bottle of traction fluid is plenty enough for one supercharger service (typically 750ml). 
Show More Show Less
Packaged by Turner - Corporate Logo
T#:554454
Part#: N55BMWKT
In Stock at Vendor
Sale - Save 8% $ 200.99

This product was last offered at the strikethrough price on
06-09-2026

$ 185.68 USD
Free Shipping
Sale - Save 8%
$ 200.99

This product was last offered at the strikethrough price on
06-09-2026

$ 185.68 USD
Free Shipping

Over time, accessory belts begin to wear out and crack. This can lead to the belt slipping, squeaking, or even snapping. Replace your belts and tensioners on a regular basis to ensure you don't end up stranded on the side of the road with a dead battery or over heated engine due to a bit of simple overlooked maintenance. This kit includes all of the items that will need replaced such as the belts, tensioners, and hardware.

For vehicles with dynamic or adaptive drive 

Fits the following BMWs:
F01/02 BMW
 740i/Li/Li xDrive
F10 BMW 535i/i xDrive
F12/3 BMW 640i/i xDrive
F15 BMW X5 s/xDrive35i
F16 BMW X6 s/xDrive35i

Show More Show Less