BMW Engine Parts for BMW X Series E70 (2007-2013)

This sensor monitors the position of the Valvetronic eccentric shaft and feeds data back to the ECU. The common issue with this sensor is that it gets contaminated with oil and fails. It doesn't give a fault code or check engine light, however. What you would notice is sluggish driving, hesitation, poor performance, jerky shifts from an automatic, and other drivability issues. These types of issues are typically diagnosed as ignition coils (which are their own issue altogether) but this sensor may also be faulty.

The eccentric shaft sensor is located at the front of the cylinder head and is only accessible with the valve cover off. It's easy to check for oil by removing the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside, or even on the valve cover itself, the sensor is likely contaminated or ready to fail. You can wipe or clean the oil from sitting inside the sensor but it will come back.

If you're planning this job make sure you have our Valve Cover Overhaul Kit, which includes a new seal for the eccentric sensor as well as the rest of the valve cover and Valvetronic gaskets. You can add the valve cover set from the options below.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008+ E82 BMW 128i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2006-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive
2010+ F07 BMW 535i GT, 535i xDrive GT, 550i GT, 550i xDrive GT
2011 F10 BMW 528i
2006-2010 E83 BMW X3 3.0i X3 3.0si
2011 F25 BMW X3 xDrive28i
2007-2010 E70 BMW X5 3.0si X5 xDrive30i
2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive30i

A cracked valve cover can cause a myriad of problems none of which are inexpensive. A simple oil leak may prove nothing more than a driveway nuisance; however, the damage that can occur as a result of low oil do more to drain the wallet. A small vacuum leak may cause only a minor hesitation but the reduced efficiency means less mpg's and more trips to the pump. This factory replacement valve cover will get you back on the road and ensure a solid and tight seal along the top end of the engine. 
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Cylinder Head Cover -
This item fits the following BMW Chassis:
E71,E82,E90,E92,E93,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F32,F33,F34,F36

Fits BMW Engines including:
N55
 

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

BMW N52 3.0L, N55 3.0L Timing Chain Tensioner With Guard Rail

Ensure proper engine performance and prevent catastrophic damage with the BMW N52 3.0L, N55 3.0L Timing Chain Tensioner With Guard Rail. This essential component maintains tension on the timing chain, preventing slack that can lead to skipped teeth and engine failure.

Benefits:

• Maintains proper tension on the timing chain
• Prevents skipped teeth and potential engine damage
• Includes guard rail for added protection
• Quiets noisy timing chains

Keep your BMW engine running smoothly and reliably with the BMW N52 3.0L, N55 3.0L Timing Chain Tensioner With Guard Rail.

The Borescope Inspection Camera offers 1920P HD resolution, a flexible 7.9mm probe, and a 16.4ft semi-rigid cable, making it ideal for inspecting hard-to-reach areas. Easily connect to IOS and Android devices, and use the IP67 waterproof probe for various applications, including automotive, plumbing, and home inspections.

Key Features:

• 1920P HD Resolution: Capture clear images and high-quality video at 1920x1440 resolution.
• Easy Connection: Connect quickly to IOS 9.0+ and Android 7+ devices via the 'SUP-ANESOK' app.
• Semi-Rigid Cable: 16.4ft cable offers a mix of flexibility and rigidity for precise inspections.
• Waterproof Probe: IP67-rated, capable of operating underwater up to 3.28 feet for 1 hour.
• Wide Applications: Suitable for automotive, plumbing, and home inspections, with adjustable brightness for low-light environments.

Includes:

• Borescope Camera
• Android Adapter
• Lightning Port Adapter
• USB Type-C Connector
• 16.4 ft. Semi-Rigid Cable
• Magnet
• Hook
• Mirror
• Protective Cap
• Manual

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

BMW N52 3.0L Ultimate Valve Cover Gasket Set is designed to provide a comprehensive solution for sealing and protecting the critical components of your engine. This complete gasket set includes the valve cover gasket, eccentric shaft sensor gasket, and VANOS solenoid gaskets, ensuring a proper seal to prevent oil leaks and maintain optimal engine performance. Perfect for BMW N52 3.0L engines, this kit from Turner Motorsport offers reliable protection against wear and tear, helping to keep your engine running smoothly and efficiently.

• Complete gasket set for BMW N52 3.0L engines
• Includes valve cover gasket, eccentric shaft sensor gasket, and VANOS solenoid gaskets
• Prevents oil leaks and maintains engine performance
• Ensures a tight seal for critical engine components
• Helps prolong engine life and reduce maintenance issues
• Quality parts from Turner Motorsport for dependable results

Upgrade to the BMW N52 3.0L Ultimate Valve Cover Gasket Set from Turner Motorsport for comprehensive sealing and enhanced engine protection.

This kit includes every thing needed to replace your rod bearings.

Kit includes

Upper and lower WPC-treated rod bearings Hardware Oil filter BMW TwinPower Turbo Oil Oil pan gasket RedLine assembly lube