BMW Engine Parts for BMW X Series E71 (2008-2014)

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

For BMW M54 applications, coil styles vary between M or N depending on the vehicle's production date. Models produced up to September 2002 require the M series style coil, while those manufactured after September 2002 use N series style coils. It's crucial to visually compare and verify the correct coil needed for your vehicle before making a purchase.

Benefits:

• Specific coil styles for different BMW M54 application dates
• Helps ensure the right replacement part for your vehicle's coil
• Visual verification recommended prior to purchase for compatibility

This eccentric shaft is a vital component of your BMW's N55 Valvetronic system, responsible for precise control of valve lift. In the N55 engine, the Valvetronic system uses intermediate levers between the camshaft and lifters to adjust valve lift dynamically. These levers are actuated by this eccentric shaft, which is rotated by an electronically controlled motor under the direction of the engine computer.

Eccentric shaft failure is a common issue in N55 engines, often caused by inadequate lubrication due to extended oil change intervals. The most frequent failure occurs when the eccentric shaft gear wears down, leading to disengagement from the motor's worm drive. Symptoms include multiple fault codes, such as P1014 (Shaft Parity Error), P1017 (Shaft Sensor Plausibility), P1023 (Valvetronic Adjustment Range), and P10E1 (Valvetronic System No Travel Detected).

If your BMW is experiencing Valvetronic-related fault codes, a failing eccentric shaft could be the source of the problem. Opt for this premium direct replacement from Bremmen Parts to restore your Valvetronic system's functionality and ensure a durable, high-quality repair.

BMW N63 4.4L Ignition Service Kit provides everything necessary for a comprehensive ignition service upgrade, featuring high-performance red Dinan ignition coils. This kit is designed specifically for BMW vehicles with the N63 4.4L engine, ensuring optimal ignition performance and enhanced engine responsiveness. By replacing aging components with top-quality parts, this service kit improves overall engine efficiency and reliability.

• Complete Ignition Upgrade: Includes all components required for a full ignition service, ensuring optimal performance.
• High-Performance Ignition Coils: Features red Dinan ignition coils that enhance spark efficiency and improve throttle response.
• Enhanced Engine Efficiency: Promotes better fuel combustion and improved power output for a more responsive driving experience.
• Quality Components: Manufactured with premium materials for durability and long-lasting performance.
• Easy Installation: Designed for straightforward installation, suitable for both professional mechanics and DIY enthusiasts.

Upgrade your BMW’s ignition system with the BMW N63 4.4L Ignition Service Kit for superior engine performance and reliability.