BMW 1 Series E82 (2008-2013)

An easy way to improve the performance of your N54 powered BMW is by removing the stock air box and swapping in this Dual Cone Intake "DCI" from Burger Motorsports. Featuring two S&B inverted cone filters with adapter couplers and new hardware, these easily install into the stock box location, allowing for greatly improved intake air flow. This is great for both stock and modified vehicles, as this allows for greater air flow at all RPMs and removes the air restriction that would normally rob your engine of power.

In addition to increased power, these filters give your engine a more aggressive appearance and sound that any automotive enthusiast will appreciate.

MADE IN THE USA

**CARB Approved Under Executive Order (EO) No. D-744-2 for all 2007-2012 BMW models equipped with the N54 3.0L twin-turbocharged 6-cylinder engine.**

Oil venting and circulation continues to be a problem on BMW engines and now even more so on the turbocharged N54 and N55 engines. The existing stock system does a very poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. We're seeing a lot more 135 and 335 cars with drivability and performance issues because oil has sneaked by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media blasting of the intake valves to strip away the oily buildup we have seen.

Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. The Burger Tuning oil catch can is the best we have seen so far. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine.

The BMS Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). The BMS OCC also has a factory-like appearance. Since BMS designed their catch can from scratch they can guarantee it fits and performs correctly for the N54/N55 engine, unlike other catch cans on the market that are poorly retrofitted from other applications and under-sized for the N54 engine.

Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles

BMS Oil Catch Can Features:
+ Increases air intake efficiency
+ Promotes engine longevity
+ Double-baffled design allows excellent air/oil separation
+ Large In/Out ports (no tapered sizes that slow flow)
+ Stealth mounting on cooler side of engine bay (promotes condensation of oil to vapor)
+ Anodized black lightweight aluminum
+ N54 version mounts out of sight under the cowl
+ Made in USA with a lifetime guarantee

Silver 18x9.5" ET22 Concave APEX ARC-8 Wheel.

Wheel Specs

Fitment:Rear

Size:18x9.5"

Offset (mm):22

Weight (lbs):19.2

Profile:Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit many BMW models and may fit other models with a specific wheel spacer. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.