Showing 10712 results for ""

• All-in-one valve cover overhaul
• Preventative replacement saves time and trouble later on
• Includes new oil separator system
• Replace valve cover gaskets before a leak becomes worse
• Replace valve cover before it cracks

For the 2007 model year BMW switched to a plastic valve cover on the N51 and N52 engines. As we have seen over time the plastic can crack which leads to oil leaks, vacuum leaks, poor running, and other issues. Unfortunately, it's not just the gasket that needs periodic replacement but the entire valve cover itself. This kit includes a new valve cover, gaskets, eccentric shaft seal, and hardware. The valve cover also incorporates the oil separator which is not a replaceable item on its own. So a complete valve cover replacement will tackle multiple problem areas at once. The valve cover is the same for N51 SULEV and N52 engines.

Cracked Valve Cover. The plastic used for the N52 valve cover is thin and weak in certain spots. This makes it prone to hairline or larger cracks that will leak oil and cause vacuum leaks. You might also notice rough running, especially at idle. Often a technician will go looking for a failed ignition coil, spark plug, or failed vacuum hose on the engine. And without a fault code to assist in diagnosis this can often mean wasted time and money. A cracked valve cover is a new problem area that many techs don't think to check.

Oil Separator/Crankcase Vent. BMW integrated the oil separator system into the valve cover on these later engines. An internal manifold creates a cyclone effect and centrifugal force separates vapor from the liquid oil. The liquid oil is supposed to drain through the valve cover and back to the oil pan while the remaining vapor is burned up during combustion. It's a very efficient and environmentally-friendly design with very few moving parts. Unfortunately it's not perfect and eventually the internal passageways will become clogged. This problem is made worse in cars that have short drive cycles, sit for long periods of time, do not have frequent oil changes, do not see regular runs to redline, and cars in freezing climates. If the engine never reaches optimal operating temp the oil remains in liquid form or becomes sludge. This is bad news for the entire engine, leading to fouled spark plugs, rough running and misfires and even premature failure of catalytic converters and oxygen sensors. Since the oil separator system in the valve cover is not available on its own, and cleaning it is nearly impossible, the complete replacement of the valve cover is the only option. Other oil vent tubes and vacuum hoses are also recommended to get replaced at the same time.

Valve Cover Gaskets. As with any rubber part, failures occur when the rubber becomes dry and brittle. The pliable rubber no longer forms a seal between the cylinder head and valve cover where it will develop an oil leak. Valve cover gaskets that leak can allow oil to seep into the spark plug holes and contaminate ignition coil boots and plugs. That can lead to rough running and misfires. A new valve cover includes new gaskets.

Eccentric Shaft Seal. The seal for the eccentric shaft sensor is a known spot for oil leaks. When the seal to the valve cover fails oil can end up in the sensor itself and ruin the sensor (an unecessary $300 expense). Usually a new seal (o-ring) will stop the leaks but sometimes the valve cover is at fault too. A new eccentric shaft seal is included.

All new hardware is included to avoid re-using and over-tightening the original bolts (they have a very low torque rating).

Replacement requires accessing the rear of the engine with a lot of the upper plastic shrouding removed. The vent hose on the valve cover should be replaced as it is almost always broken anyway (#11157559528). The metal fuel line must also be removed and disconnected from the fuel injectors. Professional installation is encouraged if you have never done this kind of work before. Serious DIY types should have a Bentley Service Manual to use which greatly explains the process. You may also want to combine this work with the oil filter housing gasket replacement.

There is no maintenance or replacement interval for the N52 valve cover. However, we have seen cracks and other failures in the 50,000-90,000 mile range. Our best advice is to plan on a major top end overhaul around the 70-80,000 mile mark. There's no mechanical downside to replacing it as prevention and it will make the engine run better and last longer.

This item fits the following BMWs:
2008-2012 E82 BMW 128i
2007-2011 E90 BMW 328i 328xi 328i xDrive - Sedan
2007-2012 E91 BMW 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2008-2010 E60 BMW 528i 528xi 528i xDrive
2011 F10 BMW 528i
2007-2010 E83 BMW X3 3.0i X3 3.0si
2007-2008 E70 BMW X5 3.0si
2007-2008 E85 BMW Z4 3.0i Z4 3.0si
2009-2010 Z4 BMW Z4 sDrive30i

This is the stock twin mass flywheel for early N54 engines in the E82 135i, E9X 335i/xi, and E60 535i/xi (flywheel uses 8 mounting bolts). It's manufactured by OEM Shaeffler (LuK). Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008-1/2009 E82 BMW 135i
2007-1/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-1/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-1/2009 E93 BMW 335i - Convertible
2007-1/2009 E60 BMW 535i 535xi 535i xDrive

To reduce the understeering affects of a staggered wheel setup you want a balanced set of sway bars. ECS has configured this anti-roll bar set for E82 1-series and E9X 3-series with a 28mm front bar and a 15mm rear bar. This kit is designed to help reduce the amount of body roll when cornering and enhance response when turning. These anti-roll bars include urethane bushings with a reinforced inner liner that eliminates squeaks and doesn't require lubrication. The bars are powder coated for durability and good looks.

These bars fit in the stock locations using the existing brackets and links. Adjustable links are not required but recommended if the car is lowered or if you have coil overs.

This item fits the following BMWs: 
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan
2007-2011 E91 BMW 325i 328i - Touring Wagon
2007-2013 E92 BMW 328i 335i 335is M3 - Coupe
2007-2013 E93 BMW 328i 335i 335is M3 - Convertible

The EVO series from ProSport Gauges is an award winning, industry leading option for those looking to push their car's limits. They allowing you to monitor crucial engine functions in one quick glance with advanced precision. Featuring a dual color readout, you can customize your readout to your liking. Offering a user friendly readout with a digital reading in the center with a bar-graph style sweep around the gauge as well. 

Kit Includes:

• 52mm Digital Boost Pressure Guage (30inHg - 35 PSI) 
• Instructions
• Tubing Kit
• T-adapter
• Premium Electric Sender
• Mounting hardware
• Blue or Red display

Unsure of what size spacer will work best for you? This professional kit includes 1mm, 2.5mm, 5mm, 10mm, and 15mm spacers with wheel studs and nuts for you play with. These are not the same spacers that we sell and they cannot be used to drive on. But with the studs installed the car can be lowered to the ground and rolled to check for clearances. These test fit spacers are drilled to fit the standard BMW 5x120 bolt pattern as well as 4-lug 4x100 (and VW/Audi bolt patterns too). You can stack spacers to achieve the perfect clearance. When you're ready call us to order the spacers you need (Turner spacers come in 3mm, 5mm, 7.5mm, 10mm, 12.5mm, 15mm, 17.5mm, 20mm, 25mm, and 30mm spacer thicknesses).

These spacers are not for driving on. They lack the hubcentric lip that BMW wheels are designed to work with. Driving on studs alone will lead to a failure.

Two ways to buy -

• Own. Just as it says, you buy this kit to own. Perfect for shops or race teams that change wheels or brake components often. For shops you can measure wheel clearance and order the correct spacers the first time around (no wasting inventory or paying return shipping). Note: Kits purchased to Own are not returnable for refunds.
• Rent. Pay the full price but get $110 as a store credit when you return the kit. We keep a modest $19.95 fee for the service. Perfect for DIY and enthusiasts who only need the Test Kit once. Use your store credit to purchase your spacers (or anything else from our catalog).

Wheel Spacer FAQ:
How to measure for wheel spacers
Wheel spacer encyclopedia

BMW N54 3.0L Stage 2 LPFP Spool Performance Bucketless is engineered by Spool Performance, a leading name in BMW forced induction, to deliver exceptional fuel delivery and power upgrades. Designed by a team of dedicated engineers, this high-quality component enhances your vehicle's fuel system with superior performance.

• Increased Fuel Flow: Provides more than double the flow of a stock fuel pump, ensuring ample fuel delivery for high-performance applications.
• E85 Capable: Fully compatible with E85 fuel, offering flexibility and efficiency.
• Drop-In Replacement: Easily replaces the factory pump without additional modifications.
• Future-Proof: Can be upgraded to Stage 3 for even greater performance as your needs evolve.

Large 5-Layer Performance Air Filter:
This sealed intake system utilizes a pre-oiled, large 5" tall conical 360 degree radial flow performance air filter with 5-layers of progressive finer mesh cotton media providing maximum airflow and performance.

Roto-mold Tube:
This System uses CAD designed, dyno-tuned, roto-mold intake tube to achieve maximum power gains while maintaining a perfect fit.

Hassle-Free Installation:
All necessary hardware are included for hassle-free installation. This is a direct bolt-on kit that requires no cutting or drilling on OEM parts.

Also available is a Magnum FORCE Intake System Cover (P/N: 54-31918-B)

Emissions Disclaimer:
This product is not currently CARB exempt and is not available for purchase in California or for use on any vehicle registered with the California Department of Motor Vehicle.

The P3 Gauge Ethanol Content Sensor with Harness (P3ESEN) provides a seamless way to access ethanol readouts on your P3 Gauge. This sensor offers a convenient solution to monitor ethanol content, ensuring you have real-time information about your fuel mixture to enhance your vehicle's performance.