BMW Suspension Parts for BMW 1 Series E82 (2008-2013)

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

• 100% machined and anodized, 6061-T6 lightweight aluminum arms
• High-strength, 3-piece, rod end (with carbon fiber reinforced, PTFE race) offers longer life for street compared to standard rod ends
• SEALS-IT Rod end seals keep dirt, water, and other contaminants out
• Rod ends feature grease fittings, to allow for rod end serviceability.
• Lighter than stock!  (Stock is 875g, RE arms are 640g)
• Extremely easy installation and adjustment (your alignment shop will LOVE you!)

Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.

Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

KONI's entry level performance STR.T (pronounced Street) shocks and struts bring improved handling and KONl quality to the budget minded driving enthusiast. Whether to simply refresh and upgrade a stock vehicle or to match with street performance lowering springs and other modifications, KONl STR.T provides performance at a value price point. 

• Entry level performance shock absorber
• Compliments lower springs
• Perfect for OE replacement or vehicle improvement
• Non-adjustable
• Lifetime Warranty

Activate your Koni Rebate!

This kit fits the following BMWs:

E82 128i 135i

Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.

Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

Bilstein strut/shock package for stock springs. Set includes 2 front Bilstein B6 Performance shocks and 2 rear Bilstein B6 Performance shocks. Includes top nuts and rear lower shock washers. The stock rear dust boots are re-used. The Bilstein B6 Performance Shock is designed for use with stock springs. These shocks provide improved handling and stability without sacrificing ride comfort.


This Bilstein B6 Performance shock package fits the following BMWs:

2008+ E82 128i Coupe, 135i Coupe 135is Coupe
2008+ E88 128i Convertible, 135i Convertible 135is Convertible

SPL Parts E8x E9x non-m adjustable toe arms replace OEM Part number 33322406290 

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

When lowering your vehicle, toe alignment is thrown off. These SPL adjustable toe arms offer a wide range of toe adjustment and are a significant improvement over stock, eliminating suspension deflection and increasing handling response thanks to the FK Bushings rod ends that are Teflon lined.

Technical Specifications:

• Gundrilled 2024 Aluminum Links to reduce unsprung weight
• 6061 Aluminum Clamps and Heim Joint Spacers
• Titanium Socket Head Cap Screws
• Rotating clamp design allows for easy access to lock down your alignment settings
• Low friction 3 piece Teflon lined FK Heim joints/rod ends made in Connecticut
• Made in the USA!

Fits the following BMWs:
2006-2013 E9X BMW RWD Non-M
2008-2013 E8X BMW 128i 135i

BMW E9X M3/E82 1M Inner Lower Tension Arm Bearing is engineered to elevate suspension performance with precision and durability. Developed by Fall-Line, known for their championship-level race cars and premium suspension components, this bearing is a significant upgrade over factory rubber bushings. Designed for motorsport applications, it incorporates FK spherical bearings for enhanced strength and longevity.

• Superior Performance: Provides a notable improvement over OEM rubber bushings for enhanced control and feedback.
• Durable Construction: Features the largest FK spherical bearings available, ensuring long-lasting reliability.
• Enhanced Control: Eliminates rubber components to offer better control over tire behavior and increased driver confidence.
• Robust Design: Equipped with stainless steel spiral locks for 360 degrees of clamping force to secure the bearing firmly.
• Long-Lasting: Outperforms OEM rubber variants, reducing the need for frequent replacements.
• Precision Engineering: CNC machined from high-quality materials in the USA for exact fit and superior performance.

This is a replacement Genuine BMW front Right lower control arm. If you are looking for a beefier, adjustable replacement set of arms, SPL offers Titanium Series Adjustable Front Lower Street Control Arms for E8X E9X RWD

Genuine BMW Repair Kit, Wishbone, Right - 31122405860

This package of OEM E82 E90 E92 diff mounts replaces the stock rubber diff bushings. On a tuned 335i you may have noticed more driveline shudder or problems hooking up during hard launches. What happens is the stock rubber bushings are under constant flex as engine torque is transmitted through the differential. Under normal driving with a stock car the bushings are rarely stressed. But factor in significant additional torque from a tuned N54/N55 and the stock rubber will quickly show its weaknesses. You may have even broken a diff bolt or two as the heavy differential shifts around. Even non-turbo E82 and E9X models may benefit from fresh bushings.

This is a set of stock rubber bushings, made by OEM supplier Lemforder. They are the same as the Genuine BMW E9X diff mount bushings, but without the more expensive branding. If you're turned off by potential side effects of urethane or Delrin then the OEM diff mounts are your best option. The OEM mounts fit and perform just like the originals so there is no second guessing their quality. If you're looking for an upgrade we offer E9X solid Delrin and aluminum diff mounts that work well, even in street applications.

E9X Diff Mount Set includes:

• 33176760287 x 2, front differential mount
• 33176770866 x 1, rear differential mount
• (new hardware is optional and can be ordered separately below)
  
  This item fits the following BMWs:
  2008-2012 E82 BMW 128i 135i
  2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan
  2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
  2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe
  2007-2013 E93 BMW 328i 335i - Convertible