BMW Tools & Specialty Equipment for BMW 1 Series E82 (2008-2013)

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

The fuel pump is held into the tank with a retaining lock ring. Most people would take an extension or punch and tap out the ring with a hammer. But that's the wrong way to do it. You could damage the lock ring, or worse, the tank itself. This handy tool is toothed to match the lock ring and takes a standard 1/2 drive ratchet or small extension. Twist the ratchet and the lock ring comes un-done cleanly and smoothly. A hefty tool that pays for itself over and over. Fits most BMWs from 1988-2013. Also has application for MINI and Porsche.

This metal screw ring tightens down to old the top of the fuel pump or fuel filter assembly dependent on model of vehicle.

Together they make this job simple and easy and ensure a tight fit with a new ring. 

46 PIECE SET:

This 1/4" set contains all the most popular tools needed to get the job done on your European car repair.

Kit Contains:

-13PCS-1/4" DR.6PT SOCKETS: 4, 4.5 , 5 ,5.5 ,6 , 7, 8 ,9 ,10, 11, 12, 13, 14MM 

-1PC- 1/4" DR. QUICK RELEASE RATCHET (72T).

-2PC- 1/4" DR.50 & 100MM EXTENSIONS 

-1PC- 1/4" DR.150MM FLEXIBLE EXTENSION

-1PC- 1/4" DR.UNIVERSAL JOINT

-1PC- 1/4" DR.SLIDING T-BAR

-1PC- 1/4" DR.6" SPINNER HANDLE

-1PC- 1/4" DR.1/4" BIT HOLDER ADAPTER

-4PCS-HEX KEY WRENCHES:1.27, 1.5,2,2.5MM

-6PCS-1/4" HEX SOCKETS:3,4,5,6,7,8MM

-3PCS-1/4' SLOTTED SOCKETS:4,5.5,7MM

-3PCS-1/4" PHILIPS SOCKETS:PH1, PH2, PH3

-3PCS-1/4"POZI SOCKETS: PZ1, PZ2, PZ3

-6PCS-1/4" TORX SOCKETS: T10, T15, T20, T25, T30, T40

TRIM/MOLDING SET:

Plastic five-piece tool kit removes trim and door panels, moldings, and adhesive backed logos and badges, without damage.

Made of impact resistant plastic that will not mar surfaces as metal screwdrivers and pry bars will. Slim design for delicate work in tight areas.

Kit includes:

• Wide edge remover

• Narrow edge remover

• Pull-type remover

• Handle remover

• Upholstery clip remover

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

2-IN-1 CREEPER SEAT:

The Schwaben 2 in 1 Creeper Seat is a versatile tool designed to enhance convenience in various maintenance tasks. Easily switch from a creeper to a stool, providing flexible options for different work scenarios. As a creeper, it allows you to slide effortlessly under your vehicle, while as a stool, it offers a comfortable seating option for low-height work, reducing strain on your back and knees.

This creeper seat features a thick, padded seat with a large vinyl cushion that remains soft and supportive. The headrest ensures comfort during extended use, and the waterproof, oilproof surface makes cleaning easy. Equipped with six 360° universal casters, it moves smoothly across different surfaces. The ball-bearing casters are compression and wear-resistant, ensuring easy maneuverability.

Constructed from thickened tubular steel, the Schwaben 2-in-1 Creeper Seat supports up to 330 lbs (150 kg), providing a sturdy and reliable platform. In stool mode, the robust frame prevents deformation, rolling, or tilting, ensuring stability.

With a ground clearance of only 3 inches, this creeper seat allows access to narrow, low-clearance spaces, making it ideal for garages and repair shops. Enjoy the convenience of switching between a creeper and a stool, and experience improved comfort and efficiency in your maintenance projects.

Key Features:

• Creeper/Stool All-in-One: Easily converts from a creeper to a stool for versatile maintenance tasks.
• Heavy-Duty Construction: Supports up to 330 lbs (150 kg) with a thickened tubular steel frame; prevents deformation, rolling, or tilting in stool mode.
• Smooth Movement: Six 360° universal casters ensure smooth and flexible movement on various surfaces; ball-bearing casters are compression and wear-resistant.
• Low Ground Clearance: Only 3 inches, allowing access to narrow and low-clearance spaces, perfect for garages and repair shops.
• Comfortable Padded Seat: Thick vinyl cushion with a headrest for extended use without fatigue; waterproof and oilproof for easy cleaning.
• Enhanced Efficiency and Comfort: Reduces strain on the back and knees, making it ideal for both routine maintenance and complex repairs.

Includes:

• 1 x Creeper Rear Frame
• 1 x Creeper Middle Frame
• 1 x Creeper Headrest
• 6 x Swivel Casters
• 6 x Washers
• 4 x M8x55 Hex Head Bolts
• 4 x M8 Lock Nuts

1/2" DRIVE METRIC SOCKET SET:

The Schwaben 1/2" Drive 6 Point Socket Set comprises a dozen 1/2" metric sockets, each featuring 6-point heads specially crafted for navigating those tricky, confined spaces.

Furthermore, our LIFETIME REPLACEMENT program provides you with added assurance, ensuring enduring performance and value. Improve your toolkit with the Schwaben 1/2" Drive 6 Point Socket Set and confidently tackle any task at hand.

Features:

• Organized Storage: Included in the set is a practical sliding rail socket holder, helping you maintain a tidy and easily accessible socket arrangement.
• Enhanced Grip: Knurled rings encircling the socket bodies ensure a secure hold, even when hands and sockets are covered in oil or grease, minimizing the risk of accidents.
• Optimal Torque: The sockets are equipped with corner radii for superior torque distribution, safeguarding fasteners from damage and ensuring efficient performance.
• High-Quality Material: Crafted from robust chrome vanadium steel (CR-V), these sockets offer superior wear resistance and toughness compared to high-speed steel, guaranteeing durability and extended lifespan.
• Satin Chrome Finish: Not only do the sockets feature an attractive satin chrome finish, but they also provide excellent corrosion resistance, ensuring long-term quality.
• Lifetime Replacement: Supported by our lifetime replacement program, this set delivers enduring value and peace of mind, making it a wise addition to your toolkit investment.

Includes:

• 10 mm
• 12 mm
• 13 mm
• 14 mm
• 15 mm
• 16 mm
• 17 mm
• 18 mm
• 19 mm
• 21 mm
• 22 mm
• 24 mm

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

TORX SCREWDRIVER SET:

Handy Torx® screwdriver set includes six common bit sizes, perfect for removing door and dashboard panels, interior trim, and smaller underhood components.

Hardened tips have center hole for use with both standard or tamper-proof Torx fasteners. Large grips add comfort and leverage. Handle through-holes make them easy to hang from pegboard hooks.

Entire kit packaged in a convenient molded case.

Sizes include: T10, T15, T20, T25, T27, and T30.

STANDARD SCREWDRIVER SET:

Elevate your craftsmanship with the Schwaben 6 Piece Screwdriver Set!

Crafted with precision and durability in mind, these professional-grade screwdrivers stand the test of time, ensuring reliable performance for countless projects.  Constructed from robust nickel chrome moly, these screwdrivers are built to endure rigorous use, making them reliable companions for various tasks. That's why it's backed by our LIFETIME REPLACEMENT program - because we want this set to stick with you as long as you need it to!

Features:

• Color-Coded Brilliance: Effortlessly switch between flat head and Philips heads, thanks to the intuitive color-coded design. Enhance efficiency and eliminate guesswork.
• Comfortable Control: Experience fatigue-free operation with the ergonomic handles, offering both comfort and precision for intricate tasks.
• Organized Housing: Housed in a molded tray, these commonly used screwdriver sizes are easily portable and organized, reducing the hassle of rummaging through toolboxes.
• Essential Sizes: Curated for versatility, the set includes sizes catering to delicate tasks and robust projects, covering all your needs.

Includes:

• 5.5x100mm flat head screwdriver

• 6.5x150mm flat head screwdriver

• 8x175mm flat head screwdriver

• #1x75mm Phillips screwdriver

• #2x100mm Phillips screwdriver

• #3x150mm Phillips screwdriver

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

LOW PROFILE JACK:

Meet the Schwaben Long Low Profile - High Lift Floor Jack: A Must-Have for BMW and MINI Enthusiasts.

Experience unmatched lifting efficiency with the Schwaben Long Low Profile - High Lift Floor Jack. Engineered with BMW and MINI enthusiasts in mind, this jack boasts a unique blend of features tailored to your beloved vehicles.

Key Features:

• Swift Reach: Innovative One Pump feature ensures quick contact with most cars.
• Versatile Reach: Ultra-long arm accommodates lowered cars and high vehicles like trucks and SUVs.
• Safety Assured: Overload system prevents usage beyond its rated capacity, enhancing security.
• Precision Control: Universal joint on the handle offers precise load management.
• Seamless Positioning: Swivel saddle and rear casters enable easy jack placement.
• Vehicle Care: Soft foam sleeve on the handle safeguards your vehicle's finish.
• Protective Padding: Rubber saddle pad shields your car during lifting.
• Added Convenience: Equipped with a tool tray on the jack for lug nuts and tools.
• LIFETIME REPLACEMENT: If this jack is injured in the line of duty, it will be backed by our lifetime replacement policy!

Specifications:

• Minimum Height: 2-3/4"
• Maximum Height: 24"
• Handle Length: 49-1/4"
• Jack Body Length: 35"
• Distance to Jack Pad Center from Pivot Point: 22"
• Front Caster Dimensions: 2-1/2" diameter x 2" width
• Saddle Diameter: 4" with full saddle pad
• Max Weight Capacity: 4000 lbs.
• ANSI / ASME PALD 2009 Certified

DRAIN PAN:

Features:

• Use it for oils or coolant
• Only 125mm high!
• Rolls on 4 casters for ease of use

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Aluminum 3-Ton Jack Stands With Mechanic's Folding Ground Pad - Set Of 2 are designed for exceptional performance and convenience in automotive maintenance. These lightweight aluminum jack stands provide robust support, while the mechanic's folding ground pad ensures comfort during vehicle work.

• Lightweight Construction: Each jack stand weighs only 4.7 lbs, making them easy to handle without sacrificing strength.
• Durable Design: All-aluminum construction with heavy-duty flanged bases ensures stability and safety for loads up to 3 tons.
• Adjustable Heights: Features 6 locking positions with a minimum height of 10.6 inches and a maximum height of 15.4 inches.
• Secure Load: Extra heavy-duty load pin with a posi lock ball mechanism keeps the pin securely in place.
• Large Base: Equipped with a 7-inch diameter base for enhanced stability.
• Mechanic’s Ground Pad: Provides comfort with high-density foam and a heavy-duty cover that resists oils and fluids. Measures 17"W x 47"L when unfolded and includes built-in carrying handles.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

The Universal 40 Piece Metric Socket Set includes all of the necessary tools to create a socket set by purchasing only one ratchet. The included 3/8-inch drive flex head ratchet and two female 3/8-inch drive adapters will allow you to use 3 different drive sizes of sockets: 1/4", 3/8", and 1/2"! Use this kit to help complete your tool kit until you decide to purchase more ratchet sizes, and when you do, you don't have to get rid of any of these tools to do so, which is possible with the adapters.

And of course, this kit is included in our LIFETIME REPLACEMENT program!

Includes:

• 4 mm (1/4" Drive)
• 4.5 mm (1/4" Drive)
• 5 mm (1/4" Drive)
• 5.5 mm (1/4" Drive)
• 6 mm (1/4" Drive)
• 7 mm (1/4" Drive)
• 8 mm (1/4" Drive and 3/8" Drive)
• 9 mm (1/4" Drive and 3/8" Drive)
• 10 mm (1/4" Drive, 3/8" Drive, and 1/2" Drive)
• 11 mm (1/4" Drive and 3/8" Drive)
• 12 mm (1/4" Drive and 3/8" Drive, and 1/2" Drive)
• 13 mm (1/4" Drive and 3/8" Drive, and 1/2" Drive)
• 14 mm (1/4" Drive and 3/8" Drive, and 1/2" Drive)
• 15mm (3/8" Drive and 1/2" Drive)
• 16mm (3/8" Drive and 1/2" Drive)
• 17mm (3/8" Drive and 1/2" Drive)
• 18mm (3/8" Drive and 1/2" Drive)
• 19mm (3/8" Drive and 1/2" Drive)
• 21mm (1/2" Drive)
• 22mm (1/2" Drive)
• 24mm (1/2" Drive)

Harmonic Balancer Puller and Installer Set

The Harmonic Balancer Puller and Installer Set is an essential tool kit designed for the effective removal and installation of harmonic balancers. This master set includes all the necessary bolts and adapters required for a wide range of applications, making it a versatile addition to any workshop or toolbox.

Benefits:

• Comprehensive Set: Includes all required bolts and adapters for most applications, ensuring compatibility with various vehicle models.
• Bilingual Instructions: Comes with bilingual instructions for easy use and understanding, catering to a broader range of users.
• Replacement Part Availability: Replacement parts are readily available, ensuring the tool kit remains functional and useful over time.
• Efficient Performance: Streamlines the process of removing and installing harmonic balancers, saving time and effort.
• Durable Construction: Built from high-quality materials for long-lasting durability and reliable performance.

BRAKE CALIPER PISTON TOOL SET:

The Schwaben 18-piece disk brake retractor tool kit screws brake caliper pistons back into their bores to make room needed for new brake pads. An essential tool for working on calipers with threaded pistons, the kit comes with both right-hand and left-hand thread screw jacks, press plate, and 15 different diameter press disks to fit a wide variety of vehicles, both import and domestic, including Audi, BMW, Ford, GM, Honda, Mazda, Mitsubishi, Subaru, Toyota, Volkswagen and others.

Made of 100 percent chromalloy steel for strength, durability, and long service life.

PROTECTA SOCKET SET:

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

CALIPER HOOK SET:

• Tired of messing with bent coat hangers or bungee cords to hang your calipers up and out of the way when performing brake maintenance? These hooks make working on your brakes easier by letting you hang your calipers with ease, no more fighting with the bungee cords or zip ties to hold the caliper just right or having to make your own "custom" hooks with wire.
• Holds brake calipers out of the way while working on brakes
• Also use to hang other automotive parts and tools while working on your vehicle.
• Stronger than zip ties or wire.
• Save the brake hose by not hanging caliper by hose.
• Made of  thick steel for strength and durability. length is 8"

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Elevate your lifting experience with the Schwaben Long Low Profile - High Lift Floor Jack. Certified for excellence and designed with a keen understanding of European car enthusiasts' needs, this jack is a testament to precision, durability, and performance. Don't compromise on quality—choose the Schwaben advantage for all your lifting endeavors.

Designed with precision, crafted for performance, and backed by our lifetime replacement program, the Schwaben Long Low Profile - High Lift Floor Jack is a must-have tool for every European car aficionado. This jack is engineered to cater to the unique needs of low ground clearance vehicles, ensuring that your prized possessions are lifted with care and precision.

Key Features:

• One Pump Reach: With its innovative one-pump feature, this floor jack effortlessly reaches contact on most cars, streamlining your lifting process.
• Low Profile Advantage: Boasting a mere 2-3/4" low height and a deep-reach lift arm, this jack is tailored for those sports cars and luxury vehicles that ride close to the ground.
• Hydraulic System Protection: The dual pump pistons are expertly shielded to thwart contaminants from compromising the hydraulic system's integrity.
• Built for Durability: Crafted with heavy gauge construction and fortified with rolled edges, this floor jack guarantees unwavering strength and longevity.
• Precise Control: The U-Joint release mechanism offers meticulous control over load descent at any handle position, ensuring the safety of both you and your vehicle.
• Maneuverability Redefined: Upgraded casters allow seamless maneuverability and effortless positioning of the jack, empowering you to find that perfect lifting spot.
• Safety First: The internal by-pass valve prevents over-pumping, shielding the hydraulic system from stress-induced issues.
• Vehicle Protection: A full cover rubber saddle pad and a protective foam cover on the handle are in place to prevent any unintended damage during the lifting process.
• Impressive Capacity: With a remarkable 4000 lb. capacity, this jack is ready to tackle a range of European vehicles.
• LIFETIME REPLACEMENT: Like almost all Schwaben products, this jack is backed by our lifetime replacement program in case anything goes wrong!

Specifications:

• Min Height: 2-3/4"
• Max Height: 24"
• Handle Length: 49-1/4"
• Jack Body Length: 35"
• Length from Pivot Point to Center of Jack Pad: 22"
• Front Casters: 2-1/2" diameter x 2" width
• Saddle Diameter: 4" with full saddle pad
• Weight Capacity: 4000 lbs.
• ANSI / ASME PALD 2009 Certified

Also included are the Schwaben Aluminum 3-Ton Jack Stands. These ultra-light Schwaben jack stands only weigh 4.7 lbs each. Fit and finish on these stands show how much pride in workmanship goes into our stands. These stands feature all-aluminum construction with heavy-duty flanged bases to safely stabilize loads. Features 6 locking positions for a secure load in multiple heights. The load pin is extra heavy duty at .584 in. diameter and features a posi lock ball to ensure the pin stays in place.  

• Min. Height is 10.6".
• Max Height is 15.4".
• Large 7" diameter base.
• Outer support tube is 2-1/8" in diameter.

For replacement parts, please call us and ask for:

• ES#4430428 - Replacement Screw Set
• ES#4430429 - Replacement Front Wheel
• ES#4430430 - Replacement Caster Wheel

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.