BMW Drivetrain Parts for BMW 1 Series E82 (2008-2013)

Turner Motorsport Lightweight N54 Flywheel & Upgraded Clutch Kit

Unlock the full potential of your N54-powered BMW with our performance-driven clutch and flywheel kit. Designed to enhance daily drivability while delivering increased power handling and improved throttle response, this kit is the ultimate upgrade for enthusiasts seeking more from their vehicle.

Why Choose This Kit?
This setup features the Turner Lightweight N54 Flywheel, precision-engineered for quicker acceleration, faster rev-matching, and a more responsive driving experience. Paired with an upgraded OE clutch from the high-performance 335is and F10 550i(V8 Bi-Turbo), this combo is capable of handling over 500 ft-lbs of torque while maintaining smooth, factory-like engagement and durability.

The factory dual-mass flywheel may prioritize smoothness and efficiency, but it comes at the cost of responsiveness and is prone to failure in high-performance applications. The Turner Lightweight Flywheel solves these issues with a single-mass design that strikes the perfect balance between comfort, performance, and reliability making it ideal for both daily driving and spirited track use.

Kit Contents:

Turner Lightweight N54 Single-Mass Flywheel (18.6 lbs, 10 lbs lighter than stock)
Upgraded OE Clutch – Supports 500 ft-lbs+
OE Clutch Fork - P# 21517564027
OE Throwout Bearing
Clutch Alignment Tool - P# 056212LA01A
Brass Clutch Fork Pivot Pin - P# 21511223328
OE Flywheel Bolts - P# 11227520706
OE Pressure Plate Screws - P# 21207548052
Pivot Pin Retaining Spring - P# 21517570284
Transmission Mating Dowels - P# 11117524470
Flywheel Features:

Precision-machined 4140 HT heat-treated chromoly steel for durability
Black oxide coating to resist corrosion
8620 steel pilot bearing pin for maximum wear resistance
Precision balanced to exceed OEM standards
Optimized step height for longer clutch life and consistent performance
Clutch:

Upgrade for 135i/335i/535i models from the 335is! Featuring a heavy-duty clutch with more holding power and a stock-like pedal feel. Excellent solution for If your clutch is slipping, or the engagement isn't what it used to be, it's time for a replacement. Slipping clutches won't allow your BMW to accelerate properly and can pose problems under a load such as going up large inclines. Also, a worn clutch can cause less precise and engaging shifts. By replacing your clutch you will restore performance and driving pleasure.

This clutch is an excellent upgrade for non 335is/550i/650i models. It features a more heavy-duty clutch disc and more holding power with stock-like pedal effort.

Transform your driving experience with this Turner Motorsport clutch and flywheel kit - engineered for power, performance, and everyday reliability.

Enhance your car's performance with ECS Tuning's polyurethane transmission mounts, designed for both street and track applications. These mounts are engineered to withstand high torque and forced-induction scenarios, eliminating concerns about torn mounts and providing a more engaging driving experience. Although polyurethane may introduce some additional NVH (Noise, Vibration, Harshness), its exceptional durability, wear resistance, and resistance to water, oil, and grease make it the perfect choice for performance enthusiasts. ECS Tuning offers two durometer options to match your driving style, along with a comprehensive DIY installation guide, ensuring a complete solution for your transmission mount requirements.

Key Features:

• Minimized transmission movement, reducing the risk of mis-shifts and over-revs.
• Made from high-quality polyurethane bonded with 304 Stainless Steel.
• Enhanced driving experience for both street and track enthusiasts.
• Two durometer options available: 80A for race applications and 70A for daily driving (ES#2859359).
• Replaces weak OEM mounts.

A common source of leaks, the selector shaft seal should be replaced whenever the shifter assembly is serviced to prevent fluid loss.

Fits the following BMW chassis:
E36, E39, E46, E36/7 Z3

The ECS Tuning Center Support Bearing Brace is engineered to improve drivetrain performance and longevity. The factory center support bearing features internal an internal rubber bushing to reduce NVH (noise, vibration, and harshness) transmission to the cabin. Unfortunately, this material choice falls short when it comes to performance applications. Under extreme load conditions, this bushing is prone to flexing, resulting in driveshaft misalignment. To address the shortcomings of the factory rubber center support carrier design, ECS engineers developed a set of precision-fit, split polyurethane bushings that secure tightly around the existing driveshaft bearing. Constructed from 90A durometer polyurethane, this material eliminates bushing deflection while maintaining minimal noise, vibration, and harshness (NVH). By eliminating deflection, this innovative solution not only improves durability but also ensures a significantly longer service life than the OEM center support bearing—making it an excellent upgrade for aging BMW chassis.

The polyurethane bushings are surrounded by a robust 6061-T6 billet aluminum bracket designed with strength and reliability in-mind. This bracket features a split design for hassle-free installation, eliminating the need to remove the driveshaft assembly entirely. To install the ECS Center Support Carrier, simply cut around your existing bearing, remove the factory brace, and clamp on your new bushings and bracket. This user-friendly approach saves time and simplifies maintenance or upgrades. Two stainless steel socket head screws are used to fasten the two-piece bracket, offering corrosion resistance and secure clamping under high torque and stress. This combination of materials and design ensures dependable performance and long-lasting durability, even in demanding applications.

Features & Benefits:

Performance-Designed Bushing Upgrade: 90A durometer polyurethane is used to eliminate bushing deflection while maintaining a smooth, quiet ride. Improved Longevity: Polyurethane construction offers a longer lifespan than factory rubber, ideal for enthusiasts looking to eliminate future CSB-related problems. Billet Aluminum Bracket: The upgraded bushings are encased in a 6061-T6 billet aluminum bracket for enhanced durability and improved performance. Easy Installation: Both the bushings and the bracket feature a two-piece split design, allowing for seamless installation without driveshaft removal. Reduce Deflection, Increase Rigidity: Designed with performance in mind, this upgrade eliminates excessive driveshaft movement for improved alignment and efficiency. Kit Includes:

ECS Driveshaft Center Support Bushings ECS Driveshaft Center Support Carrier (2) Stainless Steel Hex Head Screws (2) Hex Bolts (22326760945) Medium Strength Threadlocker (0.5ml)