BMW Engine Parts for BMW 1 Series E82 (2008-2013)

N-Series Ultimate Performance Ignition Coil - Red - Set Of Six ...

10X Entries Into Our F80 M3 Sweepstakes

T#:23714967

Part#: NSERIESIGNCOILKT

In Stock

$ 205.99 USD

Add to Wish List

Qty

$ 205.99 USD

Add to Wish List

Upgrade your BMW's engine performance with the Dinan Performance Ignition Coil Service Kit. These high-quality ignition coils are crafted to enhance ignition power, ensuring optimal engine performance and efficiency. Engineered for durability and reliability, these coils provide improved throttle response, smoother idle, and enhanced fuel efficiency. Benefit from the Dinan Performance Ignition Coil Service Kit, designed to unleash the true potential of your BMW's engine.

Show More Show Less

BMS N54 Upgraded Replacement PCV Valve For BMW

T#:38587650

Part#: N54PCVVR

In Stock

$ 40.00 USD

Add to Wish List

Qty

$ 40.00 USD

Add to Wish List

The BMS N54 Upgraded Replacement PCV Valve is a high-performance upgrade designed to enhance crankcase ventilation and minimize excessive blow-by in BMW N54 engines. Unlike the stock PCV valve, which can degrade over time and lead to oil consumption or boost leaks, this upgraded version provides superior sealing and long-term durability. ### Key Features: - **Direct-Fit Replacement** – Designed for an exact fit, ensuring hassle-free installation. - **Optimized Ventilation** – Improves crankcase pressure management, reducing oil blow-by and deposits. - **Enhanced Durability** – Constructed from premium materials to withstand high-boost applications and prolonged use. - **Boost Leak Prevention** – Delivers a tighter seal than the factory valve, preventing power loss. - **Ideal for Tuned Engines** – A critical upgrade for N54-powered vehicles running increased boost levels. Upgrade your N54’s crankcase ventilation system with the BMS Upgraded PCV Valve to ensure maximum performance, reliability, and engine longevity.

Show More Show Less

Billet Oil Filter Cap

T#:21045489

Part#: BMS-OFC

In Stock

Starting at $ 89.00 USD

Add to Wish List

Starting at $ 89.00 USD

Add to Wish List

The Burger Motorsports V2 billet aluminum oil filter cover is a metal upgrade that directly replaces your weak OE plastic cap for greater protection, better cooling, ease of removal/install, and looks great under the hood. The built-in 21mm hex and a 3/8" drive socket wrench fitting that does not require a special removal/install tool like the factory cap. Uses the OE oil filter, filter housing o-ring, and filter cage. Anodized for protection. This quality part is a must for any serious BMW owner. Replaces OEM part number 11427525334 - BMW Oil filter cover. Features and Benefits Solid aluminum design is much stronger than brittle plastic 21mm hex head + 3/8" drive socket wrench fitting Integrated heat sinks for better oil cooling Special tools are not required for removal/install like the factory cap Strong design won't fail under pressure Reuses OE filter cage and o-ring Anodized for protection Looks great under the hood Made in the USA

Show More Show Less

N54/N55 Low Temp Oil Thermostat Kit - 70c

10X Entries Into Our F80 M3 Sweepstakes

T#:52621839

Part#: 008731KT1

In Stock

Sale - Save 23% $ 74.98

This product was last offered at the strikethrough price on
05-03-2026

$ 57.74 USD

Add to Wish List

Qty

Sale - Save 23%

$ 74.98

This product was last offered at the strikethrough price on
05-03-2026

$ 57.74 USD

Add to Wish List

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Show More Show Less

MAC Single Turbo Boost Solenoid - N54 N55

T#:587715

Part#: MACSTS

In Stock

$ 51.99 USD

Add to Wish List

Qty

$ 51.99 USD

Add to Wish List

Use this plug and play low frequency MAC solenoid if retrofitting a single turbo kit to your N54 or N55. Includes plug and play harness connector for no splicing!

Febi Engine Mount (Fits Both Left and Right Side) - E82, E88, E90, E9...

We Price Match - Give Us A Call or Chat!

T#:381855

Part#: 22116760330

In Stock

$ 82.99

This product was last offered at the strikethrough price on
05-10-2026

$ 58.99 USD

Add to Wish List

Qty

$ 58.99 USD

Add to Wish List

Keep your engine securely mounted

N52 Oil Filter Housing Gasket Kit - Includes Oil Pressure Sensor ...

10X Entries Into Our F80 M3 Sweepstakes

T#:15677580

Part#: 11427540759-KT

In Stock

Sale - Save 1% $ 45.99

This product was last offered at the strikethrough price on
05-03-2026

$ 45.34 USD

Add to Wish List

Qty

Sale - Save 1%

$ 45.99

This product was last offered at the strikethrough price on
05-03-2026

$ 45.34 USD

Add to Wish List

This kit includes: 1 Oil Filter Housing Gasket (11428637821) 1 M8x28 bolt (11427540759) 1 M8x43 bolt (11427540763) 1 M8x78 bolt (11427540758) 1 Oil Pressure Sensor (12617568480)

VANOS Solenoid Valve Kit - N52 N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:25805743

Part#: 11367585425TKT

In Stock

Sale - Save 25% $ 150.99

This product was last offered at the strikethrough price on
05-03-2026

$ 112.55 USD

Add to Wish List

Qty

Sale - Save 25%

$ 150.99

This product was last offered at the strikethrough price on
05-03-2026

$ 112.55 USD

Add to Wish List

Failed solenoid valves can lead to numerous issues, such as sluggish acceleration, rough idle, loss of power, limp mode, and check engine lights. Luckily, these issues are easily fixed with our budget-friendly VANOS Solenoid Valve Kit. This kit contains two URO brand VANOS Solenoids, two sets of OEM Elring gaskets, and two Genuine BMW mounting bolts, all for less than the price of a single Genuine BMW Solenoid.

Show More Show Less

Port Injector Plugs

T#:27171925

Part#: UNI-BMS-PIPLUGS

In Stock

$ 60.00 USD

Add to Wish List

Qty

$ 60.00 USD

Add to Wish List

These dummy injectors fit in place of port injection fuel injectors to block the holes. Allows use to aluminum manifolds with port injection bungs without having to purchase fuel injectors. Plugs are EV14 injectors and measure 38mm or 1.5" from o-ring to o-ring.

Show More Show Less

Burger Motorsport 4 BAR TMAP Sensor & Adapter - BMW N55/N54/S55 (2007...

T#:34885402

Part#: 4BAR TMAP

Back Ordered

$ 139.99 USD

Add to Wish List

Qty

$ 139.99 USD

Add to Wish List

Use these plug and play adapters to quickly adapt a 4bar TMAP sensor to your N54/N55/S55 BMW, raising the boost maximum boost range from 20psi factory up to 43psi.

Spark Plug Gapper Tool BMS Billet

T#:26404907

Part#: 12MMSPG

In Stock

$ 35.00 USD

Add to Wish List

Qty

$ 35.00 USD

Add to Wish List

Spark Plug Gapper Tool BMS Billet is essential for accurately adjusting the gap of spark plugs. This precision tool ensures that each plug is set to the exact specifications required for optimal engine performance. Made in the USA, it features a 12mm plug thread size, making it suitable for a wide range of applications.

Precision Adjustment: Allows for accurate gap adjustments to ensure optimal spark performance and engine efficiency.
Speed and Efficiency: Streamlines the process of gapping plugs while maintaining high precision, saving time and effort.
High-Quality Construction: Crafted from billet materials for durability and reliability, ensuring long-term use.
Lifetime Replacement Program: Comes with a lifetime replacement guarantee, reflecting confidence in the tool's quality and performance.

Upgrade your spark plug maintenance with the Spark Plug Gapper Tool BMS Billet for a reliable and precise solution.

Show More Show Less

N54 Valve Cover Upgrade Kit - BMW N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:25772568

Part#: 11127565284MTKT

In Stock

Sale - Save 23% $ 547.99

This product was last offered at the strikethrough price on
05-03-2026

$ 419.23 USD

Add to Wish List

Qty

Sale - Save 23%

$ 547.99

This product was last offered at the strikethrough price on
05-03-2026

$ 419.23 USD

Add to Wish List

The stock plastic valve cover from BMW tends to warp and crack over time due to numerous heat cycles. This leads to oil and vacuum leaks that both make a mess and negatively affect performance and reliability. Replace your stock valve cover with this aluminum upgrade from Bremmen Parts to eliminate these issues! The aluminum construction results in a significantly stronger valve cover that won't warp or crack. This kit contains everything you need to upgrade your cover, including the upgraded aluminum valve cover, valve cover gasket, oil cap, and hardware. Additionally, we've also included a new PCV blow-by hose and a Vargas PCV upgrade for additional reliability! This is especially important for tuned vehicles with upgraded turbos.

Show More Show Less

BMW E6X / E8X / E9X - N52 Replacement Starter Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15777314

Part#: SR0492NKT2-KT

In Stock

Sale - Save 8% $ 296.99

This product was last offered at the strikethrough price on
03-17-2026

$ 273.79 USD

Add to Wish List

Qty

Sale - Save 8%

$ 296.99

This product was last offered at the strikethrough price on
03-17-2026

$ 273.79 USD

Add to Wish List

Is your car having trouble starting? Does your starter click when you turn the key? Sounds like it's time for a new starter motor! Includes new starter with no core charge, intake gaskets, throttle body gasket and hardware.

Show More Show Less

Accessory Belt Service Kit w/ Kevlar Reinforced Belt - BMW E82/88 E9X...

10X Entries Into Our F80 M3 Sweepstakes

T#:22163422

Part#: 11287568247TKT

Ships in 1 Business Day

Sale - Save 15% $ 209.99

This product was last offered at the strikethrough price on
04-15-2026

$ 178.94 USD

Add to Wish List

Qty

Sale - Save 15%

$ 209.99

This product was last offered at the strikethrough price on
04-15-2026

$ 178.94 USD

Add to Wish List

Eliminate your squeaking accessory belt pulley and cracked drive belt with this upgraded accessory belt service kit! This kit includes the ECS Kevlar Reinforced Drive Belt, tensioner assembly, and idler pulleys. ECS Tuning's Red Kevlar Accessory Belts are both an aesthetic improvement and a performance alternative to a traditional belt. Kevlar-reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM-style belts. Refreshing the rollers and/or tensioners simultaneously is a great way to ensure all vital components of your drive belt system are functioning optimally for years to come!

Show More Show Less

BMW N52 Valve Cover & PCV Valve Refresh Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:21735875

Part#: VALVECVRN52KT

Ships in 3 Business Days

Sale - Save 11% $ 465.99

This product was last offered at the strikethrough price on
05-30-2026

$ 412.93 USD

Add to Wish List

Qty

Sale - Save 11%

$ 465.99

This product was last offered at the strikethrough price on
05-30-2026

$ 412.93 USD

Add to Wish List

Maintaining the peak performance and reliability of your BMW N52 engine is essential for a smooth and enjoyable driving experience. One of the most effective ways to achieve this is by replacing critical components like the valve cover, crankcase vent hose, angle connector with heating element, and cylinder sleeve. In this article, we'll delve into the numerous benefits of upgrading these vital parts, ensuring your BMW N52 operates at its best. Optimized Engine Performance: Replacing the valve cover, crankcase vent hose, angle connector, and cylinder sleeve enhances your BMW N52's engine performance. The valve cover plays a crucial role in sealing the engine, preventing oil leaks and ensuring optimal valve operation. When you upgrade these components, you reduce the risk of performance-robbing oil leaks and maintain precise valve timing, resulting in improved horsepower and torque. Enhanced Reliability: Reliability is paramount for any BMW owner. These components, when aged or damaged, can lead to severe engine issues. By replacing them, you significantly reduce the likelihood of unexpected breakdowns or costly repairs, ensuring your BMW N52 engine runs smoothly and reliably for years to come. Improved Fuel Efficiency: An efficiently operating engine not only performs better but also consumes less fuel. The replacement of these components leads to better combustion, reduced emissions, and ultimately improved fuel efficiency. This means fewer trips to the gas station and a lighter environmental footprint. Reduced Maintenance Costs: Regular maintenance and repairs can add up over time. By proactively replacing the valve cover, crankcase vent hose, angle connector, and cylinder sleeve, you mitigate the risk of more extensive engine damage that could lead to expensive repairs down the road. In the long term, this can translate into significant cost savings. Extended Engine Lifespan: The longevity of your BMW N52 engine is directly tied to the quality and condition of its components. When you invest in high-quality replacements, you're effectively extending the lifespan of your engine. This not only preserves the value of your BMW but also allows you to enjoy its performance for years to come. Precise Temperature Control: The angle connector with heating element is vital for maintaining optimal engine temperature, especially in cold weather. A malfunctioning or worn-out connector can disrupt temperature control, affecting engine performance. Replacing this component ensures consistent and precise temperature management. Customized Upgrades: When replacing these components, you have the opportunity to choose high-performance or specialized alternatives, allowing you to customize your BMW N52 to your preferences. Whether you prioritize power, efficiency, or specific driving conditions, there are options available to tailor your engine's performance accordingly. Included in the BMW N52 Valve Cover & PCV Valve Refresh Kit: 6 Cylinder Sleeves 1 Alternator Mounting Screw Set 1 Angle Connector with Heating Element 1 Valve Cover - Gasket Included 1 Crankcase Vent Hose

Show More Show Less

70c Low Temp Oil Thermostat Kit - N54/N55

10X Entries Into Our F80 M3 Sweepstakes

T#:30031507

Part#: N54N55LTKT1

Back Ordered

Sale - Save 18% $ 152.97

This product was last offered at the strikethrough price on
05-03-2026

$ 125.58 USD

Add to Wish List

Qty

Sale - Save 18%

$ 152.97

This product was last offered at the strikethrough price on
05-03-2026

$ 125.58 USD

Add to Wish List

Upgrade your stock oil cooler thermostat for improved performance. Swap out your existing cover with ease, replacing it with a durable billet cover. Upgrade from your 110-degree Celsius thermostat to a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly unlike thermostat bypass kits.

Kit contents:

Billet thermostat housing cover
Replacement gasket
Hardware
Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Show More Show Less

Rod Bearing Replacement Kit - E9X E82/88 N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:24145933

Part#: E9XN54RBRLMKT

In Stock

Sale - Save 2% $ 467.99

This product was last offered at the strikethrough price on
08-31-2026

$ 457.48 USD

Add to Wish List

Qty

Sale - Save 2%

$ 467.99

This product was last offered at the strikethrough price on
08-31-2026

$ 457.48 USD

Add to Wish List

This kit includes everything needed to replace your rod bearings. Kit includes Upper and lower road bearings Hardware Oil filter Molygen New Generation Engine Oil (5w-40) - 7 Liters Oil pan gasket RedLine assembly lube

Show More Show Less

N54 AC Delete Accessory Belt Kit - BMW N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:26771665

Part#: 7PK1660KT

In Stock

Sale - Save 13% $ 75.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.28 USD

Add to Wish List

Qty

Sale - Save 13%

$ 75.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.28 USD

Add to Wish List

This AC Delete Accessory Belt Kit includes a new idler pulley and a shorter ECS Kevlar belt for deleting your AC compressor. ECS Tuning Performance Kevlar reinforced belts give you that extra piece of mind! Kevlar-reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM-style belts. Tensile strength Elongation Hardness Temperature and oil resistance per standard JASO E 109-94 Flex testing per SAE J2432

Show More Show Less

Performance Rod Bearing Replacement Kit - N55 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:36032373

Part#: N55-WPC-RBKT2

In Stock

Sale - Save 6% $ 844.90

This product was last offered at the strikethrough price on
05-03-2026

$ 790.38 USD

Add to Wish List

Qty

Sale - Save 6%

$ 844.90

This product was last offered at the strikethrough price on
05-03-2026

$ 790.38 USD

Add to Wish List

This kit includes every thing needed to replace your rod bearings.

Kit includes

Upper and lower WPC-treated rod bearings Hardware Oil filter BMW TwinPower Turbo Oil Oil pan gasket RedLine assembly lube

Show More Show Less

Accessory Belt Service Kit w/ Kevlar Reinforced Belt - BMW N52 ...

10X Entries Into Our F80 M3 Sweepstakes

T#:22130432

Part#: 11287530314TKT

In Stock

Sale - Save 18% $ 127.99

This product was last offered at the strikethrough price on
05-03-2026

$ 104.71 USD

Add to Wish List

Qty

Sale - Save 18%

$ 127.99

This product was last offered at the strikethrough price on
05-03-2026

$ 104.71 USD

Add to Wish List

Eliminate your squeaking accessory belt pulley and cracked drive belt with this upgraded accessory belt service kit! This kit includes the ECS Kevlar Reinforced Drive Belt, tensioner assembly, and idler pulley. ECS Tuning's Red Kevlar Accessory Belts are both an aesthetic improvement and a performance alternative to a traditional belt. Kevlar-reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM-style belts. Refreshing the rollers and/or tensioners simultaneously is a great way to ensure all vital components of your drive belt system are functioning optimally for years to come!

Show More Show Less

Dry N55 Rod Bearing Replacement Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:40782380

Part#: N55RODBRGDRYKT

In Stock

Sale - Save 3% $ 399.64

This product was last offered at the strikethrough price on
05-03-2026

$ 389.08 USD

Add to Wish List

Qty

Sale - Save 3%

$ 399.64

This product was last offered at the strikethrough price on
05-03-2026

$ 389.08 USD

Add to Wish List

This kit includes everything needed to replace the rod bearings in your N55 engine other than the engine oil and assembly lube. Kit includes Upper and lower rod bearings Hardware Oil filter Oil pan gasket

Show More Show Less

N55 Rod Bearing Replacement Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:23913954

Part#: N55RODBRGKT

In Stock

$ 510.62 USD

Add to Wish List

Qty

$ 510.62 USD

Add to Wish List

This kit includes everything needed to replace the rod bearings in your N55 engine. Kit includes Upper and lower rod bearings Hardware Oil filter BMW TwinPower Turbo Oil Oil pan gasket RedLine assembly lube

Show More Show Less

N54 Turbocharger Installation Kit - Front And Rear

10X Entries Into Our F80 M3 Sweepstakes

T#:15511873

Part#: 114275634530KT

Ships in 8 Business Days

Sale - Save 12% $ 299.95

This product was last offered at the strikethrough price on
05-03-2026

$ 264.60 USD

Add to Wish List

Qty

Sale - Save 12%

$ 299.95

This product was last offered at the strikethrough price on
05-03-2026

$ 264.60 USD

Add to Wish List

Ensure proper sealing when installing the turbos on your N54. Kit includes: 16 - ASA M7x39 studs 16 - Flange nuts All required gaskets and o-rings Water pump install hardware Replacement vacuum hose T-bolt clamps Helpful hints: For complete installation instructions, refer to Haynes Service Manual (ES2500921). Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal. If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side. To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well. Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced. Torque specs: Bracket to cylinder head: 9Nm Coolant supply line to crankcase: 9Nm Coolant return line to crankcase: 8Nm Coolant return line to turbo: 8Nm Coolant supply line to supply line: 8Nm Exhaust manifold heat shield: 8Nm Oil supply line to crankcase: 20Nm Oil pressure line to turbo: 8Nm Oil return line to crankcase: 8Nm Oil return line to turbo: 8Nm Turbo manifold to head: 20Nm

Show More Show Less

Top-Tier BMW N54/N55 Ignition Service Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:21670137

Part#: TMSN5SPCOILKT

In Stock

Sale - Save 13% $ 285.99

This product was last offered at the strikethrough price on
05-03-2026

$ 248.31 USD

Add to Wish List

Qty

Sale - Save 13%

$ 285.99

This product was last offered at the strikethrough price on
05-03-2026

$ 248.31 USD

Add to Wish List

Upgrade your BMW N54 and N55 engine with Packaged by Turner kits for optimized performance and fuel efficiency. Our BMW ignition coils feature specialized modifications to boost firepower, delivering increased torque at lower RPMs and more horsepower at higher RPMs. The extent of improvement depends on your engine's current condition, but you'll undoubtedly experience a noticeable difference in performance. Ensure your BMW's engine runs smoothly and efficiently with our comprehensive ignition service kit from ECS Tuning. This kit includes six Bav Auto ignition coils with plug boots, NGK spark plugs, American Grease Stick dielectric grease, and a BMW spark plug service indicator label. Rest assured with a 2-year warranty on all Bavarian Autosport brand parts. Upgrade your BMW N54 and N55 engine's ignition system today for a remarkable driving experience.

Show More Show Less

Febi Timing chain kit for F3x, E9x and many other BMWs

We Price Match - Give Us A Call or Chat!

T#:38419082

Part#: 11317516074S3

In Stock

$ 370.99

This product was last offered at the strikethrough price on
04-16-2026

$ 279.99 USD

Add to Wish List

Qty

$ 279.99 USD

Add to Wish List

This Febi Timing Kit Includes Timing Chain (11317516074), Tensioner Guide Rail (11317585020), Slide Rail (11317592850), Sprocket (11317502180), Chain Tensioner and Gasket (11317584723), and Miscellaneous Hardware.

Show More Show Less

N54T/"is" Engine & Transmission Mount Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:42099844

Part#: 22116793240TKT

Ships in 3 Business Days

$ 387.99

This product was last offered at the strikethrough price on
05-06-2026

$ 381.99 USD

Add to Wish List

Qty

$ 381.99 USD

Add to Wish List

Whether you're building a dedicated track car or upgrading your street BMW, the N54T/"is" Engine & Transmission Mount Kit is an essential component for maximizing drivetrain performance and reliability.

Show More Show Less

AutoTecknic Dry Carbon Competition Oil Cap Cover - Type 1 - For Vario...

T#:39971047

Part#: BM-0007

In Stock

$ 64.99 USD

Add to Wish List

Qty

$ 64.99 USD

Add to Wish List

a precision-engineered, lightweight dry carbon fiber upgrade designed to enhance the engine bay of compatible BMW models with an aggressive motorsport look and easy OEM-style installation.

Turbo Coolant Line Kit - E60, E82, E88

10X Entries Into Our F80 M3 Sweepstakes

T#:42099865

Part#: 11537558900TKT

In Stock

Sale - Save 23% $ 253.99

This product was last offered at the strikethrough price on
05-03-2026

$ 194.66 USD

Add to Wish List

Qty

Sale - Save 23%

$ 253.99

This product was last offered at the strikethrough price on
05-03-2026

$ 194.66 USD

Add to Wish List

Prevent overheating issues and protect your turbo system with the Turbo Coolant Line Kit, the complete solution for keeping your N54 engine running at peak performance.

Cam Bearing Ledge Replacement Kit - BMW N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:23748158

Part#: 11127531224TKT

In Stock

$ 1,650.31 USD

Add to Wish List

Qty

$ 1,650.31 USD

Add to Wish List

Have your camshaft bearing ledges seen better days? This kit includes everything needed to replace your cam bearing ledges with Genuine BMW and high-quality OEM components. Included in this kit: Intake Cam Bearing Ledge Exhaust Cam Bearing Ledge Valve Cover Gasket Timing Chain Tensioner Cylinder Head Hardware Assembly Lubricant BMW Engine Oil Hengst Oil Filter

Show More Show Less

Improved Racing BMW Oil Cooler Thermostat (180F)

T#:27171935

Part#: IRTHERM

Back Ordered

Starting at $ 318.99 USD

Add to Wish List

Starting at $ 318.99 USD

Add to Wish List

Precise Oil Temperature Control for Your BMW Upgrade your BMW N20, N26, N51, N52, N53, N54, N55, and S55 engine's oil temperature control with Improved Racing's high-performance oil cooler adapter. Designed to address flaws in the factory's restrictive oil cooler adapter and faulty internal flow control valve, this upgrade ensures precise oil temperature control. Improved Racing's thermostat provides quick engine warmup, prevents overcooling, and delivers full oil cooling capacity on demand. Trusted by professional race teams around the globe, Improved Racing's thermostats have proven highly reliable, are backed by a lifetime warranty, and are made in the USA. Option to Use the Factory Oil Cooler and Lines The optional factory oil line adapter allows you to use the factory oil cooler lines for a simple, plug-and-play installation. For maximum performance, the factory oil cooler and lines may be replaced with an aftermarket cooler and AN lines using the AN adapter fittings (-10AN line size is recommended). Please note that some applications, such as most BMW SUV's, use a water-to-oil heat exchangers. These applications require plugging the coolant supply and return ports, as well as adding an external air-to-oil cooler and lines (factory or aftermarket). Please note the Oil cooler adapter cannot be used without an oil cooler.

Show More Show Less

Basic High Pressure Fuel Pump Replacement Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15644266

Part#: 13517616170-KT

In Stock

$ 1,678.35

This product was last offered at the strikethrough price on
06-19-2026

$ 1,677.85 USD

Add to Wish List

Qty

$ 1,677.85 USD

Add to Wish List

HPFP woes? Replacement high pressure exchange pump for the N54 engine. Kit includes: Remanufactured High-pressure fuel pump Intake manifold gasket sets Throttle body gasket

Liqui Moly Longtime High Tech Oil Change Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15644259

Part#: 07119963129-KT

Ships in 2 Business Days

Sale - Save 14% $ 115.98

This product was last offered at the strikethrough price on
08-31-2026

$ 100.16 USD

Add to Wish List

Qty

Sale - Save 14%

$ 115.98

This product was last offered at the strikethrough price on
08-31-2026

$ 100.16 USD

Add to Wish List

To keep your driving machine in top shape, regular maintenance is imperative. BMW's service interval for an oil change varies based on driving habits. We recommend changing your oil after no more than 10,000 miles. A 5,000 oil service interval is preferred for aggressive or city driving. This kit contains Seven Liters of Liqui Moly Longtime High Tech Engine Oil 5w-30 Engine Oil Filter Oil Drain Plug Gasket (Included with filter kit)

Show More Show Less

Accessory Belt Service Kit w/ Kevlar Reinforced Belt - BMW E82/88 E9X...

10X Entries Into Our F80 M3 Sweepstakes

T#:22163417

Part#: 11287582946TKT

Ships on Nov 12, 2026

$ 223.76 USD

Add to Wish List

Qty

$ 223.76 USD

Add to Wish List

Eliminate your squeaking accessory belt pulley and cracked drive belt with this upgraded accessory belt service kit! This kit includes the ECS Kevlar Reinforced Drive Belt, belt tensioner, and idler pullies. ECS Tuning's Red Kevlar Accessory Belts are both an aesthetic improvement and a performance alternative to a traditional belt. Kevlar-reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM-style belts. Refreshing the rollers and/or tensioners simultaneously is a great way to ensure all vital components of your drive belt system are functioning optimally for years to come!

Show More Show Less

Febi Outdoor Temperature Sensor / Probe

We Price Match - Give Us A Call or Chat!

T#:382731

Part#: 65816936953

Ships in 1 Business Day

$ 20.47 USD

Add to Wish List

Qty

$ 20.47 USD

Add to Wish List

Common fix for incorrect OBC temperature readings

Valvetronic Camshaft Adjuster replacement kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15677492

Part#: 11127556161-KT

In Stock

Sale - Save 19% $ 220.99

This product was last offered at the strikethrough price on
05-03-2026

$ 179.28 USD

Add to Wish List

Qty

Sale - Save 19%

$ 220.99

This product was last offered at the strikethrough price on
05-03-2026

$ 179.28 USD

Add to Wish List

Valv-tronic adjuster unit, Changes the the timing shaft to adjust the valve timing.

OEM Febi Eccentric Shaft - BMW N55 S55 3.0L

We Price Match - Give Us A Call or Chat!

T#:31522948

Part#: 11377589883F

Ships in 2 Business Days

$ 1,014.99

This product was last offered at the strikethrough price on
05-04-2026

$ 910.73 USD

Add to Wish List

Qty

$ 910.73 USD

Add to Wish List

The eccentric shaft is an important component of BMW's Valvetronic system, a form of variable valve lift control. If the teeth on the gear or the lobes have worn out, this can result in improper valve lift, decreased or abnormal performance, and even damage to cylinder head components. Replace your eccentric shaft with this high-quality part from OEM Febi to restore performance and eliminate valve lift issues without the marked-up price of a Genuine BMW eccentric shaft.

Show More Show Less

Coolant Port Block Off Plugs for N54 Single Turbo Conversion ...

For use with converted single turbo N54 engines

T#:23880741

Part#: N54STCCPBO

In Stock

$ 30.00 USD

Add to Wish List

Qty

$ 30.00 USD

Add to Wish List

If you're installing a single turbo kit on your N54-powered BMW, you'll need to block off the two coolant ports on the exhaust side of the engine block. This kit contains high-quality billet aluminum plugs for both the front and rear location factory coolant feed locations.

Show More Show Less

Eccentric Shaft Replacement Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:22789670

Part#: S55SHAFTRPCKT

In Stock

$ 1,209.99

This product was last offered at the strikethrough price on
08-24-2026

$ 1,208.99 USD

Add to Wish List

Qty

$ 1,208.99 USD

Add to Wish List

Ensure the peak performance of your BMW N55 or S55 engine with Turner Motorsport's Eccentric Shaft Replacement Kit. This all-inclusive kit features essential components, including:

Camshaft
Eccentric Shaft Bearing
Valve Cover Gasket Set
Gasket

Designed for precision and durability, this kit guarantees optimal engine performance and longevity. Rely on Turner Motorsport for top-quality replacement parts that adhere to the highest standards.

Show More Show Less

Billet Spark Plug Gapper Tool - 14mm - BMS

T#:583132

Part#: BMSBSPGT14MM

Ships in 7 Business Days

$ 35.00 USD

Add to Wish List

Qty

$ 35.00 USD

Add to Wish List

BMS Billet Spark Plug Gapper Tool - 14mm is an essential tool for achieving accurate and consistent spark plug gapping, ideal for automotive enthusiasts and professional mechanics alike. This precision tool helps maintain optimal plug performance by providing reliable, consistent gaps. Available in both 14mm and 12mm plug thread sizes, this tool is proudly made in the USA to deliver durability and precision.

Precisely gaps spark plugs for enhanced engine performance and efficiency
Speeds up the gapping process while ensuring accuracy and uniformity
Available in two sizes (14mm and 12mm) for a wider range of compatibility
Optional specialty feeler gauge included with 4 blades in thicknesses of .018, .020, .022, and .024
Made in the USA for premium quality and durability

Show More Show Less

Wastegate Repair Kit - N54

10X Entries Into Our F80 M3 Sweepstakes

T#:41863724

Part#: 116575857456TKT

Ships on Sep 22, 2026

$ 164.99 USD

Add to Wish List

Qty

$ 164.99 USD

Add to Wish List

Get rid of that annoying N54 Wastegate Rattle for good!

Fuel Injector Replacement Kit - N52

10X Entries Into Our F80 M3 Sweepstakes

T#:53044116

Part#: 13537531634RKT2

Ships on Oct 14, 2026

Sale - Save 22% $ 318.99

This product was last offered at the strikethrough price on
05-03-2026

$ 247.50 USD

Add to Wish List

Qty

Sale - Save 22%

$ 318.99

This product was last offered at the strikethrough price on
05-03-2026

$ 247.50 USD

Add to Wish List

Restore engine performance and drivability by replacing those old, high mileage fuel injectors. Includes injector clips.

Febi Oil Filter Housing Replacement Kit - 11428683206

For vehicles with High Speed Synchronization (oil cooler) option

We Price Match - Give Us A Call or Chat!

T#:28337870

Part#: 11428683206

Back Ordered

$ 251.99 USD

Add to Wish List

Qty

$ 251.99 USD

Add to Wish List

These aluminum filter housings are prone to cracking, which can lead to oil leaks and serious engine damage. To avoid such issues, it's essential to replace the entire housing and cooler assembly.

Fortunately, Febi provides a top-quality reproduction unit at a much lower cost than genuine parts. If you require a replacement filter housing, opting for Febi-Bilstein ensures a cost-effective and durable solution.

Show More Show Less

Ignition Service Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15677540

Part#: 12138616153-KT

Ships in 1 Business Day

$ 240.99

This product was last offered at the strikethrough price on
07-27-2026

$ 217.99 USD

Add to Wish List

Qty

$ 217.99 USD

Add to Wish List

If your BMW's mileage is getting up there, be sure to keep your ignition system in check. Whether you currently have a misfire or you're just doing preventative maintenance, this kit is perfect. The kit includes: 6 Coils with locks 6 spark plugs BMW spark plug service label for your records 1 packet of American Grease Stick dielectric grease

Show More Show Less

Genuine BMW Oil Change Kit / Inspection I - N52, N54, N55

10X Entries Into Our F80 M3 Sweepstakes

T#:15511870

Part#: 832123659460KT

In Stock

Sale - Save 10% $ 123.99

This product was last offered at the strikethrough price on
08-31-2026

$ 111.59 USD

Add to Wish List

Qty

Sale - Save 10%

$ 123.99

This product was last offered at the strikethrough price on
08-31-2026

$ 111.59 USD

Add to Wish List

This oil change kit has everything you need for an easy oil change, including seven liters of oil, an oil filter, and a drain plug.

Bosch Starter Motor With Hardware

10X Entries Into Our F80 M3 Sweepstakes

T#:56110332

Part#: SR0492NKT4

In Stock

$ 273.99

This product was last offered at the strikethrough price on
08-14-2026

$ 261.99 USD

Add to Wish List

Qty

$ 261.99 USD

Add to Wish List

At the core is a brand-new Bosch Starter Motor, engineered to withstand extreme operating conditions while delivering immediate cranking speed. This kit includes also the required Genuine BMW Aluminum Mounting Screw Set.

Show More Show Less

Oil Filter Housing Gasket Replacement Kit - BMW N54 N55 3.0L ...

10X Entries Into Our F80 M3 Sweepstakes

T#:24344808

Part#: N54OFHGKT

In Stock

Sale - Save 1% $ 171.99

This product was last offered at the strikethrough price on
08-18-2026

$ 171.09 USD

Add to Wish List

Qty

Sale - Save 1%

$ 171.99

This product was last offered at the strikethrough price on
08-18-2026

$ 171.09 USD

Add to Wish List

If you have a leaking oil filter housing seal, why not replace it while doing an oil service? This kit includes an Oil service kit along with an oil filter housing gasket and thermostat housing gasket.

Show More Show Less

BMW E6X / E8X / E9X / Z4 Cam Bearing Ledge Replacement Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:21703017

Part#: N54CAMBRINGKT

In Stock

$ 1,650.31 USD

Add to Wish List

Qty

$ 1,650.31 USD

Add to Wish List

Maintaining your BMW E6X, E8X, E9X, or Z4 engine health is paramount to ensure optimal performance and longevity. Two crucial components that require periodic attention are the cam bearing ledge and valve cover gasket. Regular servicing of these components, along with other critical elements such as the camshaft O-ring, chain tensioner (with gasket), and oil filter, is imperative to keep your BMW running smoothly. Included in Kit: 1 - Cam Bearing Ledge - Exhaust 29 - Torx Bolt 1 - Genuine Cam Bearing Ledge - Intake 1 - Genuine Cam Bearing Ledge - Exhaust 1 - Valve Cover Gasket 4 - Genuine Camshaft O-rings 7 - Genuine BMW TwinPower Turbo 5W-30 Engine Oil 1 - Assembly Lube 1 - Chain Tensioner - With Gasket Ring 1 - Hengst Oil Filter 2 - Collar Screws Cam Bearing Ledge: The cam bearing ledge is vital for proper camshaft support and lubrication. Over time, wear and tear can compromise its effectiveness, potentially leading to camshaft damage. Servicing this component ensures that your camshaft operates optimally, preventing costly repairs. Valve Cover Gasket: A well-maintained valve cover gasket is essential to prevent oil leaks and maintain proper sealing in the engine. Ignoring gasket issues can lead to oil contamination, loss of engine performance, and even engine damage. Camshaft O-Ring: The camshaft O-ring helps maintain proper oil pressure and prevents oil leakage. A deteriorated O-ring can result in oil seepage, leading to lubrication issues that affect engine performance and longevity. Chain Tensioner (with Gasket Ring): Proper timing chain tension is crucial for engine synchronization. Servicing the chain tensioner and its gasket ensures correct timing, preventing potential engine misfires and damage. Oil Filter: Regularly replacing the oil filter is fundamental to maintaining clean engine oil. Clean oil is essential for lubrication and heat dissipation, safeguarding the engine against wear and tear. Kit is for these BMW models: E60 / E61 - N54 3.0L E82 / E88 - N54 3.0L E90 / E92 / E93 - N54 3.0L Z4 - N54 3.0L

Show More Show Less

AutoTecknic - Carbon Competition Fuel Cap Cover - Various BMW and MIN...

T#:39971046

Part#: BM-0006-BCG

In Stock

$ 65.00 USD

Add to Wish List

Qty

$ 65.00 USD

Add to Wish List

AutoTecknic - Carbon Competition Fuel Cap Cover - Various BMW and MINI Models is a premium exterior upgrade crafted from genuine carbon fiber, designed to enhance the aggressive styling and performance aesthetic of compatible BMW and MINI vehicles with an easy, OEM-fit installation.

Show More Show Less

Ignition Service Kit - E9x, E82, E88, E70, E83

10X Entries Into Our F80 M3 Sweepstakes

T#:41425001

Part#: 12138616153T1KT

In Stock

$ 269.99 USD

Add to Wish List

Qty

$ 269.99 USD

Add to Wish List

Comes with coil packs, dialectic grease and spark plugs for an all inclusive kit for servicing your BMW!

Oil Filter Housing Gasket Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15677487

Part#: 11427542983-KT

In Stock

$ 122.99 USD

Add to Wish List

Qty

$ 122.99 USD

Add to Wish List

Over time gaskets become dry and brittle allowing oil to leak in your engine compartment. Replace this gasket and stop having to top off your oil every month. A common source of leaks on the N54/55 is the gaskets between the the thermostat plate and filter housing, and also the filter housing to engine block.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW 1 Series E82 (2008-2013)

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results