BMW Engine Parts for BMW 1 Series E82 (2008-2013)

Valvetronic Actuator Replacement Kit - BMW N55 S55 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:599759

Part#: 11377603979KT2

In Stock

Sale - Save 10% $ 268.99

This product was last offered at the strikethrough price on
05-03-2026

$ 241.95 USD

Add to Wish List

Qty

Sale - Save 10%

$ 268.99

This product was last offered at the strikethrough price on
05-03-2026

$ 241.95 USD

Add to Wish List

Includes actuator, actuator gasket and valve cover gaskets

N-Series Ultimate Performance Ignition Coil - Red - Set Of Six ...

10X Entries Into Our F80 M3 Sweepstakes

T#:23714967

Part#: NSERIESIGNCOILKT

In Stock

$ 205.99 USD

Add to Wish List

Qty

$ 205.99 USD

Add to Wish List

Upgrade your BMW's engine performance with the Dinan Performance Ignition Coil Service Kit. These high-quality ignition coils are crafted to enhance ignition power, ensuring optimal engine performance and efficiency. Engineered for durability and reliability, these coils provide improved throttle response, smoother idle, and enhanced fuel efficiency. Benefit from the Dinan Performance Ignition Coil Service Kit, designed to unleash the true potential of your BMW's engine.

Show More Show Less

Oil Filter Housing Gasket KIT

10X Entries Into Our F80 M3 Sweepstakes

T#:637846

Part#: 1142753729312KT1

In Stock

$ 97.99

This product was last offered at the strikethrough price on
08-17-2026

$ 96.99 USD

Add to Wish List

Qty

$ 96.99 USD

Add to Wish List

Over time gaskets become dry and brittle allowing oil to leak in your engine compartment. Replace this gasket and stop having to top off your oil every month. A common source of leaks on the N54/55 is the gaskets between the the thermostat plate and filter housing, and also the filter housing to engine block.

Show More Show Less

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

2X Entries Into Our F80 M3 Sweepstakes

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Oil Filter Housing Gasket Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:5403248

Part#: 11427537293TMSKT

In Stock

$ 97.99

This product was last offered at the strikethrough price on
08-18-2026

$ 96.99 USD

Add to Wish List

Qty

$ 96.99 USD

Add to Wish List

Includes gaskets and hardware to replace both oil filter housing gaskets. Over time gaskets become dry and brittle allowing oil to leak in your engine compartment. Replace this gasket and stop having to top off your oil every month. A common source of leaks on the N54/55 is the gaskets between the the thermostat plate and filter housing, and also the filter housing to engine block.

Show More Show Less

Bav Auto Spark Plug Socket 12" x 5/8"

10X Entries Into Our F80 M3 Sweepstakes

T#:580385

Part#: B8800072

In Stock

Sale - Save 25% $ 37.99

This product was last offered at the strikethrough price on
05-03-2026

$ 28.49 USD

Add to Wish List

Qty

Sale - Save 25%

$ 37.99

This product was last offered at the strikethrough price on
05-03-2026

$ 28.49 USD

Add to Wish List

Magnetic insert holds the spark plug securely in place for easy installation. Works great on many twin can engines where the spark plugs are recessed deep in the cylinder head.

N54/N55 Low Temp Oil Thermostat Kit - 70c

10X Entries Into Our F80 M3 Sweepstakes

T#:52621839

Part#: 008731KT1

In Stock

Sale - Save 23% $ 74.98

This product was last offered at the strikethrough price on
05-03-2026

$ 57.74 USD

Add to Wish List

Qty

Sale - Save 23%

$ 74.98

This product was last offered at the strikethrough price on
05-03-2026

$ 57.74 USD

Add to Wish List

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Show More Show Less

BMW Oil Cap Crankcase Breather - All BMW w/2 prong oil fill cap ...

2X Entries Into Our F80 M3 Sweepstakes

T#:558084

Part#: VTT-CRANK-BREATH

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Show More Show Less

N52 Oil Filter Housing Gasket Kit - Includes Oil Pressure Sensor ...

10X Entries Into Our F80 M3 Sweepstakes

T#:15677580

Part#: 11427540759-KT

In Stock

Sale - Save 1% $ 45.99

This product was last offered at the strikethrough price on
05-03-2026

$ 45.34 USD

Add to Wish List

Qty

Sale - Save 1%

$ 45.99

This product was last offered at the strikethrough price on
05-03-2026

$ 45.34 USD

Add to Wish List

This kit includes: 1 Oil Filter Housing Gasket (11428637821) 1 M8x28 bolt (11427540759) 1 M8x43 bolt (11427540763) 1 M8x78 bolt (11427540758) 1 Oil Pressure Sensor (12617568480)

VANOS Solenoid Valve Kit - N52 N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:25805743

Part#: 11367585425TKT

In Stock

Sale - Save 25% $ 150.99

This product was last offered at the strikethrough price on
05-03-2026

$ 112.55 USD

Add to Wish List

Qty

Sale - Save 25%

$ 150.99

This product was last offered at the strikethrough price on
05-03-2026

$ 112.55 USD

Add to Wish List

Failed solenoid valves can lead to numerous issues, such as sluggish acceleration, rough idle, loss of power, limp mode, and check engine lights. Luckily, these issues are easily fixed with our budget-friendly VANOS Solenoid Valve Kit. This kit contains two URO brand VANOS Solenoids, two sets of OEM Elring gaskets, and two Genuine BMW mounting bolts, all for less than the price of a single Genuine BMW Solenoid.

Show More Show Less

High-Performance Ignition Service Kit - BMW N52 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:583536

Part#: N52PISKT

In Stock

Sale - Save 20% $ 243.99

This product was last offered at the strikethrough price on
05-03-2026

$ 195.55 USD

Add to Wish List

Qty

Sale - Save 20%

$ 243.99

This product was last offered at the strikethrough price on
05-03-2026

$ 195.55 USD

Add to Wish List

Every 60-80,000 miles, we recommend replacing your spark plugs to ensure your ignition system is running optimally. Over time carbon can build up around the head of the spark plug and decrease spark strength and effectiveness, leading to weaker fuel mixture detonation, misfires, and potential check engine lights. To prevent this, have put together our High-Performance Ignition Service Kits. These kits include new Bav Auto High-Performance Ignition Coils, new spark plugs, dielectric grease, and a BMW spark plug service label to keep track of when your spark plugs were replaced.

Bav Auto's Ignition coils feature core windings that have been modified to increase firepower and promote a faster, more efficient burn. This gives your BMW/MINI increased torque in the lower range of RPM and more horsepower in the upper range. Exact improvements depend on the current condition of your engine, but you'll definitely feel the difference. They'll also improve your fuel economy.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Show More Show Less

Oil Pan Gasket - With Bolts

Bolts Are For Vehicles With Automatic Transmission ONLY

10X Entries Into Our F80 M3 Sweepstakes

T#:5403247

Part#: 11132210959TMSKT

In Stock

Sale - Save 3% $ 81.99

This product was last offered at the strikethrough price on
05-03-2026

$ 79.42 USD

Add to Wish List

Qty

Sale - Save 3%

$ 81.99

This product was last offered at the strikethrough price on
05-03-2026

$ 79.42 USD

Add to Wish List

Gasket between oil pan and engine block. A common piece to begin leaking on any engine, oil pan gaskets begin to leak after a few years.

VTT N54 Crank Bolt Capture - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557938

Part#: VTT-N54-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice.

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

1x Aluminum Crank Bolt Capture
8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54

Show More Show Less

OEM Accessory Belt Service Kit - N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:554448

Part#: N54ACCKT

In Stock

Sale - Save 15% $ 197.99

This product was last offered at the strikethrough price on
04-15-2026

$ 169.24 USD

Add to Wish List

Qty

Sale - Save 15%

$ 197.99

This product was last offered at the strikethrough price on
04-15-2026

$ 169.24 USD

Add to Wish List

Over time, accessory belts begin to wear out and crack. This can lead to the belt slipping, squeaking, or even snapping. Replace your belts and tensioners on a regular basis to ensure you don't end up stranded on the side of the road with a dead battery or overheated engine due to a bit of simple overlooked maintenance. This kit includes all of the items that will need replaced such as the belts, tensioners, and hardware.

Show More Show Less

Bav Auto Fuel Level Sensor & Fuel Pump Lock Ring Tool - BMW & MINI ...

10X Entries Into Our F80 M3 Sweepstakes

T#:580400

Part#: B8800089

Ships on Sep 30, 2026

Sale - Save 10% $ 72.99

This product was last offered at the strikethrough price on
05-03-2026

$ 65.69 USD

Add to Wish List

Qty

Sale - Save 10%

$ 72.99

This product was last offered at the strikethrough price on
05-03-2026

$ 65.69 USD

Add to Wish List

Used to remove fuel level and fuel pump lock rings properly to avoid damage.

Vargas N54/55 Billet Crank Seal Guard - BMW N54 N55 3.0L

2X Entries Into Our F80 M3 Sweepstakes

T#:638889

Part#: VTT-CRANKGUARD

In Stock

Starting at $ 89.99 USD

Add to Wish List

Starting at $ 89.99 USD

Add to Wish List

It is a well-known issue on the BMW N54/55 platforms that your serpentine belt can fail for various reasons. When this happens, there is a high chance of the belt getting sucked behind the front damper pulley and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure. Even if you do not lose the engine, it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT, even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Vargas' seal is different from those already on market in two major ways. Firstly, it is not offensively priced. Secondly, it is 100% billet with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long-term corrosion resistance. Crank Seal Guard includes: One VTT Billet N54/55 Crank Seal Guard Two extended 12.9 Grade bolts, and two stainless washers We highly recommend you install WITH a crank bolt capture at the same time, as you have to remove the damper anyway. Then you will get the benefit of helping eliminate the dreaded spun crank hub and the crank seal issue

Show More Show Less

N54 Valve Cover Upgrade Kit - BMW N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:25772568

Part#: 11127565284MTKT

In Stock

Sale - Save 23% $ 547.99

This product was last offered at the strikethrough price on
05-03-2026

$ 419.23 USD

Add to Wish List

Qty

Sale - Save 23%

$ 547.99

This product was last offered at the strikethrough price on
05-03-2026

$ 419.23 USD

Add to Wish List

The stock plastic valve cover from BMW tends to warp and crack over time due to numerous heat cycles. This leads to oil and vacuum leaks that both make a mess and negatively affect performance and reliability. Replace your stock valve cover with this aluminum upgrade from Bremmen Parts to eliminate these issues! The aluminum construction results in a significantly stronger valve cover that won't warp or crack. This kit contains everything you need to upgrade your cover, including the upgraded aluminum valve cover, valve cover gasket, oil cap, and hardware. Additionally, we've also included a new PCV blow-by hose and a Vargas PCV upgrade for additional reliability! This is especially important for tuned vehicles with upgraded turbos.

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

2X Entries Into Our F80 M3 Sweepstakes

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

N52 Valvetronic Camshaft Adjuster Replacement Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:5416764

Part#: 11377548388TMSKT

In Stock

Sale - Save 19% $ 220.99

This product was last offered at the strikethrough price on
05-03-2026

$ 179.28 USD

Add to Wish List

Qty

Sale - Save 19%

$ 220.99

This product was last offered at the strikethrough price on
05-03-2026

$ 179.28 USD

Add to Wish List

Includes new Valvetronic motor, gasket, and hardware. The Valv-tronic adjuster unit changes the the timing shaft to adjust the valve timing.

Bav Auto Crankshaft Front Oil Seal Removal / Installer Tool - N54, N5...

10X Entries Into Our F80 M3 Sweepstakes

T#:580444

Part#: B8800139

Ships on Sep 30, 2026

Sale - Save 5% $ 203.99

This product was last offered at the strikethrough price on
05-03-2026

$ 193.79 USD

Add to Wish List

Qty

Sale - Save 5%

$ 203.99

This product was last offered at the strikethrough price on
05-03-2026

$ 193.79 USD

Add to Wish List

Used in removal and installation of the front crankshaft seal on BMW N55 engines, a common job that you can save yourself a ton of money doing at home.

OEM Accessory Belt Service Kit - E82/88 E9X N55

10X Entries Into Our F80 M3 Sweepstakes

T#:567679

Part#: 11287582946KT4

Ships in 2 Business Days

Sale - Save 3% $ 212.99

This product was last offered at the strikethrough price on
03-19-2026

$ 206.15 USD

Add to Wish List

Qty

Sale - Save 3%

$ 212.99

This product was last offered at the strikethrough price on
03-19-2026

$ 206.15 USD

Add to Wish List

Over time, accessory belts begin to wear out and crack. This can lead to the belt slipping, squeaking, or even snapping. Replace your belts and tensioners on a regular basis to ensure you don't end up stranded on the side of the road with a dead battery or overheated engine due to a bit of simple overlooked maintenance. This kit includes all of the items that will need to be replaced such as the belts, tensioners, and hardware.

Show More Show Less

E82 135i N54, E9X 335 N54, E60 535 Vargas Upgraded PCV Valve ...

2X Entries Into Our F80 M3 Sweepstakes

T#:389684

Part#: VTT-N54-PCV

In Stock

$ 68.99 USD

Add to Wish List

Qty

$ 68.99 USD

Add to Wish List

The crankcase oil vent system on the N52/N54 is one of its weakest and cheaply designed systems. We see crankcase vent issues on even stock engines but with more boost the problems are exponential. This Vargas upgraded PCV valve, and an oil catch can, are what the N54 engine needs and may alleviate most of your oil and boost leak issues. The PCV valve is supposed to let oil either return to the oil pan or pass through the intake manifold and get burned up in the combustion chamber. However, BMW used a weak plastic vent valve that doesn't seal well when under boost. Instead of closing and venting the oil out of the intake, it's forced through this valve and into the intake and coating your valves with oil residue and carbon. Most boost equals more oil forcing its way by. This upgraded N54 PCV valve uses higher grade materials, including aluminum, to provide a better seal and prevent oil from entering the intake. It's an easy install and a must-have item when considering any turbo work.

Show More Show Less

Boost Solenoid/Pressure Converter - Kit - N54, N63

10X Entries Into Our F80 M3 Sweepstakes

T#:5416756

Part#: 11747626350TMSKT

In Stock

Sale - Save 45% $ 408.99

This product was last offered at the strikethrough price on
07-14-2026

$ 226.02 USD

Add to Wish List

Qty

Sale - Save 45%

$ 408.99

This product was last offered at the strikethrough price on
07-14-2026

$ 226.02 USD

Add to Wish List

Kit includes both boost solenoids, vacuum hose and T fitting for a easy leak free install

OEM Accessory Belt Service Kit - N52 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:593693

Part#: N52ABKT

In Stock

Sale - Save 22% $ 135.99

This product was last offered at the strikethrough price on
07-08-2026

$ 105.43 USD

Add to Wish List

Qty

Sale - Save 22%

$ 135.99

This product was last offered at the strikethrough price on
07-08-2026

$ 105.43 USD

Add to Wish List

Over time, accessory belts begin to wear out and crack. This can lead to the belt slipping, squeaking, or even snapping. Replace your belts and tensioners on a regular basis to ensure you don't end up stranded on the side of the road with a dead battery or overheated engine due to a bit of simple overlooked maintenance. This kit includes all of the items that will need replaced such as the belts, tensioners, and hardware.

Show More Show Less

Bav Auto Fuel Injector Removal/Installation Tool - N55

For E - Chassis N55

10X Entries Into Our F80 M3 Sweepstakes

T#:580388

Part#: B8800075

In Stock

Sale - Save 20% $ 109.99

This product was last offered at the strikethrough price on
05-03-2026

$ 87.99 USD

Add to Wish List

Qty

Sale - Save 20%

$ 109.99

This product was last offered at the strikethrough price on
05-03-2026

$ 87.99 USD

Add to Wish List

This tool takes the stress and difficulty out of removing and installing your N55 fuel injectors.

Accessory Belt Service Kit w/ Kevlar Reinforced Belt - BMW E82/88 E9X...

10X Entries Into Our F80 M3 Sweepstakes

T#:22163422

Part#: 11287568247TKT

Ships on Nov 12, 2026

Sale - Save 15% $ 209.99

This product was last offered at the strikethrough price on
04-15-2026

$ 178.94 USD

Add to Wish List

Qty

Sale - Save 15%

$ 209.99

This product was last offered at the strikethrough price on
04-15-2026

$ 178.94 USD

Add to Wish List

Eliminate your squeaking accessory belt pulley and cracked drive belt with this upgraded accessory belt service kit! This kit includes the ECS Kevlar Reinforced Drive Belt, tensioner assembly, and idler pulleys. ECS Tuning's Red Kevlar Accessory Belts are both an aesthetic improvement and a performance alternative to a traditional belt. Kevlar-reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM-style belts. Refreshing the rollers and/or tensioners simultaneously is a great way to ensure all vital components of your drive belt system are functioning optimally for years to come!

Show More Show Less

Bav Auto Timing Tool Kit - N51 N52 N54 N55 S55

10X Entries Into Our F80 M3 Sweepstakes

T#:580414

Part#: B8800107

Ships on Oct 20, 2026

Sale - Save 5% $ 371.99

This product was last offered at the strikethrough price on
05-03-2026

$ 353.39 USD

Add to Wish List

Qty

Sale - Save 5%

$ 371.99

This product was last offered at the strikethrough price on
05-03-2026

$ 353.39 USD

Add to Wish List

Sets cam, valve & VANOS timing on BMW N51, N52, N53, N54 & N55 engines. Includes camshaft fixture with hold-down bolts, 3 alignment gauges and TDC pin. A must when removing and replacing cylinder heads on these engines.

Show More Show Less

BMW E6X / E8X / E9X - N52 Replacement Starter Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15777314

Part#: SR0492NKT2-KT

In Stock

Sale - Save 8% $ 296.99

This product was last offered at the strikethrough price on
03-17-2026

$ 273.79 USD

Add to Wish List

Qty

Sale - Save 8%

$ 296.99

This product was last offered at the strikethrough price on
03-17-2026

$ 273.79 USD

Add to Wish List

Is your car having trouble starting? Does your starter click when you turn the key? Sounds like it's time for a new starter motor! Includes new starter with no core charge, intake gaskets, throttle body gasket and hardware.

Show More Show Less

High-Performance Ignition Service Kit - BMW N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:583535

Part#: N54PISKT1

In Stock

Sale - Save 18% $ 279.99

This product was last offered at the strikethrough price on
05-03-2026

$ 228.29 USD

Add to Wish List

Qty

Sale - Save 18%

$ 279.99

This product was last offered at the strikethrough price on
05-03-2026

$ 228.29 USD

Add to Wish List

Every 60-80,000 miles, we recommend replacing your spark plugs to ensure your ignition system is running optimally. Over time carbon can build up around the head of the spark plug and decrease spark strength and effectiveness, leading to weaker fuel mixture detonation, misfires, and potential check engine lights. To prevent this, have put together our High-Performance Ignition Service Kits. These kits include new Bav Auto High-Performance Ignition Coils, new spark plugs, dielectric grease, and a BMW spark plug service label to keep track of when your spark plugs were replaced. Bav Auto's Ignition coils feature core windings that have been modified to increase firepower and promote a faster, more efficient burn. This gives your BMW/MINI increased torque in the lower range of RPM and more horsepower in the upper range. Exact improvements depend on the current condition of your engine, but you'll definitely feel the difference. They'll also improve your fuel economy. From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty. As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform! This kit contains: 6 BOSCH Spark Plugs 6 Bavarian Autosport Ignition Coils 1 Dielectric Spark Plug Boot Protector - 4 Gram Packet

Show More Show Less

Valve Cover Gasket Overhaul Kit - E9X 328i, E60 528i, E83 X3 3.0i/si,...

For vehicles with a production date from 10/2006

10X Entries Into Our F80 M3 Sweepstakes

T#:180875

Part#: TMS180875

In Stock

$ 142.24

This product was last offered at the strikethrough price on
05-07-2026

$ 107.43 USD

Add to Wish List

Qty

$ 107.43 USD

Add to Wish List

Not only will this kit stop most E90 oil leaks, it's the perfect addition for ignition coil or spark plug replacement! Oil leaks - and the damage they can cause - seem to be the worst annoyances on these cars. The biggest source of an oil leak is from the valve cover, followed by the oil filter housing, Valvetronic seal, camshaft seals, and the eccentric shaft sensor seal. Once the oil leaks, and if ignored for an extended time, the oil will contaminate vital electrical sensors. This is especially the case with ignition coils and also the eccentric shaft sensor on the Valvetronic shaft at the top of the cylinder head. During any ignition coil and spark plug replacement take a close look inside for any oil pooling at the bottom. We have been seeing valve cover oil leaks as soon as 40,000 miles. We look for oil leaks on every E90 that comes into our shop.

We have put together this package of valve cover gaskets and other related gaskets and seals for you to fully overhaul the N52 valve cover and put a stop to those pesky oil leaks. This package has the replacement parts for N52 engines built from the 2007 model year and includes:

11127582245 - N52 valve cover gasket set
11127552280 - N52 eccentric shaft sensor seal
11127559699 - N52 Valvetronic gasket

2007 and later N51/N52 engines do not need replacement valve cover bolts, unless the bolts are actually broken off or missing. Unlike the 2006 aluminum hardware, the later parts are steel and not 1-time use.

These are all OEM or OE parts. Replacement of these gaskets and seals is straight-forward but a long process. BMW dealers typically charge for over eight hours of labor. If you have replaced spark plugs before you should be capable of this repair. In addition, there are several other parts to replace while you're in the vicinity: camshaft sensor o-rings, oil filter housing profile gasket, VAN0S solenoids, and the eccentric shaft sensor. These other parts, except the eccentric shaft sensor (see below), are replaceable without removing the valve cover but are more easily accessed during the valve cover work.

Eccentric Shaft Sensor: This is the position sensor that relays the eccentric shaft's position back to the DME. It's located at the front of the engine and is only accessible with the valve cover off . The seal around the sensor can fail and allow oil to blow out from under the cam cover. Oil can then leak into the sensor itself and cause it to fail. Without a functioning sensor your E90 can experience poor running, hesitation, poor performance, jerky shifts, and sluggish response. It's easy to check and see if oil has accumulated inside the sensor: unbolt the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside or even around the sensor itself, plan on replacing this sensor during your next ignition coil, spark plug, and/or valve cover gasket work.

This valve cover kit fits the following BMWs:
2008-2012 E82 BMW 128i
2007-2011 E90 BMW 328i 328xi 328i xDrive - Sedan
2007-2012 E91 BMW 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2007-2010 E60 BMW 528i 528xi 528i xDrive
2011 F10 BMW 528i
2007-2010 E83 BMW X3 3.0i X3 3.0si
2007-2013 E70 BMW X5 3.0si
10/2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive30i

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

BMW N52 Valve Cover & PCV Valve Refresh Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:21735875

Part#: VALVECVRN52KT

Ships in 4 Business Days

Sale - Save 11% $ 465.99

This product was last offered at the strikethrough price on
05-30-2026

$ 412.93 USD

Add to Wish List

Qty

Sale - Save 11%

$ 465.99

This product was last offered at the strikethrough price on
05-30-2026

$ 412.93 USD

Add to Wish List

Maintaining the peak performance and reliability of your BMW N52 engine is essential for a smooth and enjoyable driving experience. One of the most effective ways to achieve this is by replacing critical components like the valve cover, crankcase vent hose, angle connector with heating element, and cylinder sleeve. In this article, we'll delve into the numerous benefits of upgrading these vital parts, ensuring your BMW N52 operates at its best. Optimized Engine Performance: Replacing the valve cover, crankcase vent hose, angle connector, and cylinder sleeve enhances your BMW N52's engine performance. The valve cover plays a crucial role in sealing the engine, preventing oil leaks and ensuring optimal valve operation. When you upgrade these components, you reduce the risk of performance-robbing oil leaks and maintain precise valve timing, resulting in improved horsepower and torque. Enhanced Reliability: Reliability is paramount for any BMW owner. These components, when aged or damaged, can lead to severe engine issues. By replacing them, you significantly reduce the likelihood of unexpected breakdowns or costly repairs, ensuring your BMW N52 engine runs smoothly and reliably for years to come. Improved Fuel Efficiency: An efficiently operating engine not only performs better but also consumes less fuel. The replacement of these components leads to better combustion, reduced emissions, and ultimately improved fuel efficiency. This means fewer trips to the gas station and a lighter environmental footprint. Reduced Maintenance Costs: Regular maintenance and repairs can add up over time. By proactively replacing the valve cover, crankcase vent hose, angle connector, and cylinder sleeve, you mitigate the risk of more extensive engine damage that could lead to expensive repairs down the road. In the long term, this can translate into significant cost savings. Extended Engine Lifespan: The longevity of your BMW N52 engine is directly tied to the quality and condition of its components. When you invest in high-quality replacements, you're effectively extending the lifespan of your engine. This not only preserves the value of your BMW but also allows you to enjoy its performance for years to come. Precise Temperature Control: The angle connector with heating element is vital for maintaining optimal engine temperature, especially in cold weather. A malfunctioning or worn-out connector can disrupt temperature control, affecting engine performance. Replacing this component ensures consistent and precise temperature management. Customized Upgrades: When replacing these components, you have the opportunity to choose high-performance or specialized alternatives, allowing you to customize your BMW N52 to your preferences. Whether you prioritize power, efficiency, or specific driving conditions, there are options available to tailor your engine's performance accordingly. Included in the BMW N52 Valve Cover & PCV Valve Refresh Kit: 6 Cylinder Sleeves 1 Alternator Mounting Screw Set 1 Angle Connector with Heating Element 1 Valve Cover - Gasket Included 1 Crankcase Vent Hose

Show More Show Less

70c Low Temp Oil Thermostat Kit - N54/N55

10X Entries Into Our F80 M3 Sweepstakes

T#:30031507

Part#: N54N55LTKT1

Back Ordered

Sale - Save 18% $ 152.97

This product was last offered at the strikethrough price on
05-03-2026

$ 125.58 USD

Add to Wish List

Qty

Sale - Save 18%

$ 152.97

This product was last offered at the strikethrough price on
05-03-2026

$ 125.58 USD

Add to Wish List

Upgrade your stock oil cooler thermostat for improved performance. Swap out your existing cover with ease, replacing it with a durable billet cover. Upgrade from your 110-degree Celsius thermostat to a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly unlike thermostat bypass kits.

Kit contents:

Billet thermostat housing cover
Replacement gasket
Hardware
Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Show More Show Less

Spark Plug Set - ZGR6STE2 - 2007+ 6 Cyl. Turbo Engine (N54)

10X Entries Into Our F80 M3 Sweepstakes

T#:337998

Part#: 12120037244

In Stock

Starting at $ 116.99 USD

Add to Wish List

Starting at $ 116.99 USD

Add to Wish List

Standard replacement Genuine BMW to replace Bosch ZGR6STE2 Spark plug for N54 engines (twin turbo charged 3.0 liter) which came in all 2007, 2008 and newer E90/E92 335i, 335xi coupe and sedan, as well E60 535i & 535xi. This spark plug is often listed as BMW part# 12120034087 (12 12 0 034 087).

This spark plug set fits the following BMWs:

2007+ E90/E92 3 Series twin turbo - including 335i & 335xi (sedan, coupe, & convertibles)
2007+ E60 5 Series twin turbo - including 535i & 535xi (sedans and wagons)
2009+ Z4 BMW Z4 sDrive35i Z4 sDrive35is

Show More Show Less

Rod Bearing Replacement Kit - E9X E82/88 N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:24145933

Part#: E9XN54RBRLMKT

In Stock

Sale - Save 1% $ 467.99

This product was last offered at the strikethrough price on
08-31-2026

$ 463.30 USD

Add to Wish List

Qty

Sale - Save 1%

$ 467.99

This product was last offered at the strikethrough price on
08-31-2026

$ 463.30 USD

Add to Wish List

This kit includes everything needed to replace your rod bearings. Kit includes Upper and lower road bearings Hardware Oil filter Molygen New Generation Engine Oil (5w-40) - 7 Liters Oil pan gasket RedLine assembly lube

Show More Show Less

N54 Turbocharger Installation Kit - Front And Rear

10X Entries Into Our F80 M3 Sweepstakes

T#:401684

Part#: 13712247398KT2

In Stock

$ 406.99

This product was last offered at the strikethrough price on
08-25-2026

$ 406.36 USD

Add to Wish List

Qty

$ 406.36 USD

Add to Wish List

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

16 - ASA M7x39 studs
16 - Flange nuts
All required gaskets and o-rings
Water pump install hardware
Replacement vacuum hose
T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

Show More Show Less

Bav Auto Fuel Injector Seal Installer & Remover - N54/N63

10X Entries Into Our F80 M3 Sweepstakes

T#:580445

Part#: B8800140

In Stock

Sale - Save 3% $ 121.99

This product was last offered at the strikethrough price on
05-03-2026

$ 118.33 USD

Add to Wish List

Qty

Sale - Save 3%

$ 121.99

This product was last offered at the strikethrough price on
05-03-2026

$ 118.33 USD

Add to Wish List

This is has been specifically designed to remove and install the seals on your fuel injectors without damaging either the seals or injectors themselves.

Bav Auto Media Blaster Kit - BMW N20 N54 N55

10X Entries Into Our F80 M3 Sweepstakes

T#:582473

Part#: B1100008

In Stock

Sale - Save 8% $ 329.99

This product was last offered at the strikethrough price on
05-03-2026

$ 303.26 USD

Add to Wish List

Qty

Sale - Save 8%

$ 329.99

This product was last offered at the strikethrough price on
05-03-2026

$ 303.26 USD

Add to Wish List

Carbon building up in your intake ports? Take care of it quick and easy with this DIY media blaster kit from Bav auto. This walnut shell media blaster kit contains everything you need to effectively clean and de-carbon the intake ports and valves on your turbocharged N20, N54, or N55 BMW engine. Taking your vehicle to the dealer to have this service performed, you would be looking at a cost of around $1000 or more! This kit saves you money and can be used as many times as you need to ensure perfectly clean intake ports for optimum airflow and performance. Included in this kit: 20lb pressure feed media blaster including water separator and pressure gauge blasting wand N54/N55 port adapter (attaches to your shop vac to catch the used media and deposits) 25lb package of walnut shell blasting media Use of this kit requires a medium sized air compressor (suggested minimum 20-30 gallon tank, 4.0 CFM @ 90psi), common "shop vac" and full hearing and eye protection. We recommend the use of a remote starter switch. Please note: Intake manifold gasket set and Throttle body gasket, sold separately, must be replaced when removing intake manifold.

Show More Show Less

Vargas Ignition Coil Kit (Blue) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309605

Part#: VTT-COIL-N5X-BLU

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

N54 AC Delete Accessory Belt Kit - BMW N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:26771665

Part#: 7PK1660KT

In Stock

Sale - Save 13% $ 75.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.28 USD

Add to Wish List

Qty

Sale - Save 13%

$ 75.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.28 USD

Add to Wish List

This AC Delete Accessory Belt Kit includes a new idler pulley and a shorter ECS Kevlar belt for deleting your AC compressor. ECS Tuning Performance Kevlar reinforced belts give you that extra piece of mind! Kevlar-reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM-style belts. Tensile strength Elongation Hardness Temperature and oil resistance per standard JASO E 109-94 Flex testing per SAE J2432

Show More Show Less

Valve Cover Kit - N55

10X Entries Into Our F80 M3 Sweepstakes

T#:5376284

Part#: 11127570292TKT

In Stock

Sale - Save 5% $ 320.99

This product was last offered at the strikethrough price on
05-03-2026

$ 304.52 USD

Add to Wish List

Qty

Sale - Save 5%

$ 320.99

This product was last offered at the strikethrough price on
05-03-2026

$ 304.52 USD

Add to Wish List

If your valve cover has become cracked or warped, replace it with this Hamburg Tech cover from Turner Motorsport to prevent leaks and further valvetrain damage. Replace your leaking valve cover to keep your oil inside the engine, where it belongs. Includes everything needed to install a new valve cover: Valve cover Gasket flange Crank case vent hose Hardware

Show More Show Less

VTT N54 Billet Vacuum (Boost Control) Tank Kit - Anodized Blue - BMW ...

2X Entries Into Our F80 M3 Sweepstakes

T#:7530040

Part#: VACUUMCANBLUE

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

VTT is proud to offer their billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and use it to regulate boost via the solenoids. The stock plastic can and small plastic nipples on the stock cans have a tendency to crank over time, and if they leak you will get low boost, or no boost, and poor performance. These cans do away with the weak plastic cans while adding some pop, and color to your engine bay. These vacuum cans retain ALL of the factory provisions including mounting points but come with 90-degree fittings for easier routing of the lines VTT's cans are made of 6061-T6 aluminum, and anodized in 4 colors for beauty, and long life. They also knurl the cans for a very distinct look in the engine bay! VTT also designed these cans to complement their N54 Billet lineup – N5X Billet Oil caps, N5XBillet Oil filter housing caps, Billet coolant cap, Billet valve cover, billet oil cooler block off plate, and Billet Power Steering cap, and so on. All will have matching color These cans are offered in 4 colors – Red, Black, Blue, and Clear anodize The kit will include: 2 – Vacuum canisters (color of choice) 4 – billet 90-degree barbed fittings Requires the additional use of aftermarket vacuum line - Vacuum line not included. Replaces Genuine BMW Vacuum Canisters # 11652247620

Show More Show Less

VTT Billet Power Steering Pulley - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:7292042

Part#: VTT-N54-PSN54

Ships in 2 Business Days

Starting at $ 56.99 USD

Add to Wish List

Starting at $ 56.99 USD

Add to Wish List

Vargas has introduced their new Billet Power Steering pulleys for the N54 engine! A well-known issue with the N54 with Hydraulic power steering is the plastic pulley either hitting the subframe, or breaking on its own. This can result in the belt to be ejected from the pulley, and leave you stranded with no serpentine belt. This also increases the chance of sucking the belt into the engine through the front seal. Put an end to the dreaded plastic PS pulley issues with the VTT 100% Billet Aluminum PS pulley. These are constructed from 6061-T6 aluminum and anodize in one of 4 colors (Black, Red, Blue, and Clear) for a great look, and long-lasting finish. These weigh 11oz, very close to the weight of a stock pulley, and are lighter than the cast aluminum versions on the market.

Show More Show Less

Vargas Ignition Coil Kit (Red) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309610

Part#: VTT-COIL-N5X-RED

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

Bav Auto Crankshaft Rear Oil Seal Removal / Installer Tool - N51, N52...

10X Entries Into Our F80 M3 Sweepstakes

T#:580412

Part#: B8800104

In Stock

Sale - Save 5% $ 147.99

This product was last offered at the strikethrough price on
05-03-2026

$ 140.59 USD

Add to Wish List

Qty

Sale - Save 5%

$ 147.99

This product was last offered at the strikethrough price on
05-03-2026

$ 140.59 USD

Add to Wish List

For removal and installation of the rear crankshaft seal on BMW N51, N52 and N54 engines.

Performance Rod Bearing Replacement Kit - N55 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:36032373

Part#: N55-WPC-RBKT2

In Stock

Sale - Save 6% $ 844.90

This product was last offered at the strikethrough price on
05-03-2026

$ 790.38 USD

Add to Wish List

Qty

Sale - Save 6%

$ 844.90

This product was last offered at the strikethrough price on
05-03-2026

$ 790.38 USD

Add to Wish List

This kit includes every thing needed to replace your rod bearings.

Kit includes

Upper and lower WPC-treated rod bearings Hardware Oil filter BMW TwinPower Turbo Oil Oil pan gasket RedLine assembly lube

Show More Show Less

N54 Valve Cover upgrade kit

10X Entries Into Our F80 M3 Sweepstakes

T#:6196925

Part#: 11127565284TKT

In Stock

Sale - Save 30% $ 423.99

This product was last offered at the strikethrough price on
05-03-2026

$ 296.23 USD

Add to Wish List

Qty

Sale - Save 30%

$ 423.99

This product was last offered at the strikethrough price on
05-03-2026

$ 296.23 USD

Add to Wish List

You want to keep your N54 running properly to enjoy the drive and justify the costs associated with owning an N54 car! This kit has a replacement valve cover for your current cover that is worn or damaged. Along with replacing the valve cover this kit includes an upgraded pcv valve. This upgraded PCV valve uses machined metal components in place of the stock plastic parts, resulting in a more durable part. While replacing your valve cover a common failure is one of the blow by pcv vent hose cracks and is also INCLUDED in the kit for a full proof valve cover upgrade service! Replace and upgrade your valve cover at the same time, with the VTT PCV valve for longer PCV life and better flow.

Show More Show Less

Borescope Camera with Light For Phone

10X Entries Into Our F80 M3 Sweepstakes

T#:32450134

Part#: PHONEBORESCOPE

In Stock

Sale - Save 3% $ 58.99

This product was last offered at the strikethrough price on
05-03-2026

$ 57.22 USD

Add to Wish List

Qty

Sale - Save 3%

$ 58.99

This product was last offered at the strikethrough price on
05-03-2026

$ 57.22 USD

Add to Wish List

The Borescope Inspection Camera offers 1920P HD resolution, a flexible 7.9mm probe, and a 16.4ft semi-rigid cable, making it ideal for inspecting hard-to-reach areas. Easily connect to IOS and Android devices, and use the IP67 waterproof probe for various applications, including automotive, plumbing, and home inspections.

Key Features:

1920P HD Resolution: Capture clear images and high-quality video at 1920x1440 resolution.
Easy Connection: Connect quickly to IOS 9.0+ and Android 7+ devices via the 'SUP-ANESOK' app.
Semi-Rigid Cable: 16.4ft cable offers a mix of flexibility and rigidity for precise inspections.
Waterproof Probe: IP67-rated, capable of operating underwater up to 3.28 feet for 1 hour.
Wide Applications: Suitable for automotive, plumbing, and home inspections, with adjustable brightness for low-light environments.

Includes:

Borescope Camera
Android Adapter
Lightning Port Adapter
USB Type-C Connector
16.4 ft. Semi-Rigid Cable
Magnet
Hook
Mirror
Protective Cap
Manual

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less

VTT N54 Billet Vacuum (Boost Control) Tank Kit - Anodized Clear - BMW...

2X Entries Into Our F80 M3 Sweepstakes

T#:7530039

Part#: VACUUMCANRAW

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

VTT is proud to offer their billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and use it to regulate boost via the solenoids. The stock plastic can and small plastic nipples on the stock cans have a tendency to crank over time, and if they leak you will get low boost, or no boost, and poor performance. These cans do away with the weak plastic cans while adding some pop, and color to your engine bay. These vacuum cans retain ALL of the factory provisions including mounting points but come with 90-degree fittings for easier routing of the lines VTT's cans are made of 6061-T6 aluminum, and anodized in 4 colors for beauty, and long life. They also knurl the cans for a very distinct look in the engine bay! VTT also designed these cans to complement their N54 Billet lineup – N5X Billet Oil caps, N5XBillet Oil filter housing caps, Billet coolant cap, Billet valve cover, billet oil cooler block off plate, and Billet Power Steering cap, and so on. All will have matching color These cans are offered in 4 colors – Red, Black, Blue, and Clear anodize The kit will include: 2 – Vacuum canisters (color of choice) 4 – billet 90-degree barbed fittings Requires the additional use of aftermarket vacuum line - Vacuum line not included. Replaces Genuine BMW Vacuum Canisters # 11652247620

Show More Show Less

Oil Pan Gasket Replacement Kit

For vehicles with automatic transmission only

10X Entries Into Our F80 M3 Sweepstakes

T#:5403285

Part#: 11137548031TMSKT

Ships in 2 Business Days

$ 201.03 USD

Add to Wish List

Qty

$ 201.03 USD

Add to Wish List

Includes new pan gasket, hardware and a oil service kit. A common piece to begin leaking on any engine, oil pan gaskets begin to leak after a few years.

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW 1 Series E82 (2008-2013)

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results