BMW Engine Parts for BMW 1 Series E82 (2008-2013)

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

2X Entries Into Our F80 M3 Sweepstakes

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

BMW Oil Cap Crankcase Breather - All BMW w/2 prong oil fill cap ...

2X Entries Into Our F80 M3 Sweepstakes

T#:558084

Part#: VTT-CRANK-BREATH

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Show More Show Less

VTT N54 Crank Bolt Capture - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557938

Part#: VTT-N54-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice.

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

1x Aluminum Crank Bolt Capture
8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54

Show More Show Less

Vargas N54/55 Billet Crank Seal Guard - BMW N54 N55 3.0L

2X Entries Into Our F80 M3 Sweepstakes

T#:638889

Part#: VTT-CRANKGUARD

In Stock

Starting at $ 89.99 USD

Add to Wish List

Starting at $ 89.99 USD

Add to Wish List

It is a well-known issue on the BMW N54/55 platforms that your serpentine belt can fail for various reasons. When this happens, there is a high chance of the belt getting sucked behind the front damper pulley and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure. Even if you do not lose the engine, it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT, even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Vargas' seal is different from those already on market in two major ways. Firstly, it is not offensively priced. Secondly, it is 100% billet with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long-term corrosion resistance. Crank Seal Guard includes: One VTT Billet N54/55 Crank Seal Guard Two extended 12.9 Grade bolts, and two stainless washers We highly recommend you install WITH a crank bolt capture at the same time, as you have to remove the damper anyway. Then you will get the benefit of helping eliminate the dreaded spun crank hub and the crank seal issue

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

2X Entries Into Our F80 M3 Sweepstakes

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

E82 135i N54, E9X 335 N54, E60 535 Vargas Upgraded PCV Valve ...

2X Entries Into Our F80 M3 Sweepstakes

T#:389684

Part#: VTT-N54-PCV

In Stock

$ 68.99 USD

Add to Wish List

Qty

$ 68.99 USD

Add to Wish List

The crankcase oil vent system on the N52/N54 is one of its weakest and cheaply designed systems. We see crankcase vent issues on even stock engines but with more boost the problems are exponential. This Vargas upgraded PCV valve, and an oil catch can, are what the N54 engine needs and may alleviate most of your oil and boost leak issues. The PCV valve is supposed to let oil either return to the oil pan or pass through the intake manifold and get burned up in the combustion chamber. However, BMW used a weak plastic vent valve that doesn't seal well when under boost. Instead of closing and venting the oil out of the intake, it's forced through this valve and into the intake and coating your valves with oil residue and carbon. Most boost equals more oil forcing its way by. This upgraded N54 PCV valve uses higher grade materials, including aluminum, to provide a better seal and prevent oil from entering the intake. It's an easy install and a must-have item when considering any turbo work.

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:18733532

Part#: VTT-CRANKHUB-6

In Stock

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Vargas Ignition Coil Kit (Blue) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309605

Part#: VTT-COIL-N5X-BLU

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

VTT N54 Billet Vacuum (Boost Control) Tank Kit - Anodized Blue - BMW ...

2X Entries Into Our F80 M3 Sweepstakes

T#:7530040

Part#: VACUUMCANBLUE

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

VTT is proud to offer their billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and use it to regulate boost via the solenoids. The stock plastic can and small plastic nipples on the stock cans have a tendency to crank over time, and if they leak you will get low boost, or no boost, and poor performance. These cans do away with the weak plastic cans while adding some pop, and color to your engine bay. These vacuum cans retain ALL of the factory provisions including mounting points but come with 90-degree fittings for easier routing of the lines VTT's cans are made of 6061-T6 aluminum, and anodized in 4 colors for beauty, and long life. They also knurl the cans for a very distinct look in the engine bay! VTT also designed these cans to complement their N54 Billet lineup – N5X Billet Oil caps, N5XBillet Oil filter housing caps, Billet coolant cap, Billet valve cover, billet oil cooler block off plate, and Billet Power Steering cap, and so on. All will have matching color These cans are offered in 4 colors – Red, Black, Blue, and Clear anodize The kit will include: 2 – Vacuum canisters (color of choice) 4 – billet 90-degree barbed fittings Requires the additional use of aftermarket vacuum line - Vacuum line not included. Replaces Genuine BMW Vacuum Canisters # 11652247620

Show More Show Less

VTT Billet Power Steering Pulley - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:7292042

Part#: VTT-N54-PSN54

Ships in 2 Business Days

Starting at $ 56.99 USD

Add to Wish List

Starting at $ 56.99 USD

Add to Wish List

Vargas has introduced their new Billet Power Steering pulleys for the N54 engine! A well-known issue with the N54 with Hydraulic power steering is the plastic pulley either hitting the subframe, or breaking on its own. This can result in the belt to be ejected from the pulley, and leave you stranded with no serpentine belt. This also increases the chance of sucking the belt into the engine through the front seal. Put an end to the dreaded plastic PS pulley issues with the VTT 100% Billet Aluminum PS pulley. These are constructed from 6061-T6 aluminum and anodize in one of 4 colors (Black, Red, Blue, and Clear) for a great look, and long-lasting finish. These weigh 11oz, very close to the weight of a stock pulley, and are lighter than the cast aluminum versions on the market.

Show More Show Less

Vargas Ignition Coil Kit (Red) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309610

Part#: VTT-COIL-N5X-RED

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

VTT N54 Billet Vacuum (Boost Control) Tank Kit - Anodized Clear - BMW...

2X Entries Into Our F80 M3 Sweepstakes

T#:7530039

Part#: VACUUMCANRAW

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

VTT is proud to offer their billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and use it to regulate boost via the solenoids. The stock plastic can and small plastic nipples on the stock cans have a tendency to crank over time, and if they leak you will get low boost, or no boost, and poor performance. These cans do away with the weak plastic cans while adding some pop, and color to your engine bay. These vacuum cans retain ALL of the factory provisions including mounting points but come with 90-degree fittings for easier routing of the lines VTT's cans are made of 6061-T6 aluminum, and anodized in 4 colors for beauty, and long life. They also knurl the cans for a very distinct look in the engine bay! VTT also designed these cans to complement their N54 Billet lineup – N5X Billet Oil caps, N5XBillet Oil filter housing caps, Billet coolant cap, Billet valve cover, billet oil cooler block off plate, and Billet Power Steering cap, and so on. All will have matching color These cans are offered in 4 colors – Red, Black, Blue, and Clear anodize The kit will include: 2 – Vacuum canisters (color of choice) 4 – billet 90-degree barbed fittings Requires the additional use of aftermarket vacuum line - Vacuum line not included. Replaces Genuine BMW Vacuum Canisters # 11652247620

Show More Show Less

VTT Billet BMW Crankcase Breather - Screw In - BMW N54 N55 3.0L ...

2X Entries Into Our F80 M3 Sweepstakes
FOR MODELS WITH VTT BILLET VALVE COVER ONLY

T#:38924625

Part#: VTT-CRANKBREATHE

In Stock

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

VTT is happy to introduce the first and only available plug and play ONE-WAY crankcase breather kit for BMW B58 applications. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay. FITS with the engine cover on. Engine cover can be removed, and installed without removing the breather. This breather can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups, including most aftermarket oil catch can systems! The breather sits about 2.5' tall from the valve cover oil cap area, and the filter is 2-3/4' in diameter Is your car a Gen1 or TU? Pull your oil cap off, and check how it attaches. 2 Prong style is Gen-1, snap-in style with grooves is TU.

Show More Show Less

VTT Ignition Coil Conversion Kit - S55/N55 To B58 - Multiple Color Op...

2X Entries Into Our F80 M3 Sweepstakes

T#:22196341

Part#: VTTS55CLCNV

Ships in 6 Business Days

Starting at $ 335.99 USD

Add to Wish List

Starting at $ 335.99 USD

Add to Wish List

VTT is proud to offer its very own Game Changer S55/N55 to B58 Coil conversion kit for the BMW S55/N55 platforms. The 55 series of engines has notoriously had ignition problems with the factory coils, while aftermarket upgrades do exist, they can be bulky. The solution is the BMW B58 ignition coils which are extremely robust and can support well over 1000WHP with no issues. This means a plug-and-play affordable solution that fits like stock, and looks AMAZING doing so! We designed our own 6061-T6 Billet bracket in a plethora of colors including matching shades for every S55/N55 Valve Cover. This means you can mix and match the color of the bracket with coil color, with VC color to truly tailor your engine bay to look exactly how you want it to! The kit comes with the following: 3 – Billet Aluminum Coil Brackets in the color of choice 6 – Plug and play VTT wiring harnesses 6 – Custom VTT stalks to convert the B58 coils to the S55/N55 head (We ensure proper spring length inside the boot for optimal spring-to-plug contact) *NOTE: Flash setting changes may be required when installing the conversion kit to ensure the proper function of the B58 coils with S55/N55 DME. This can be found in almost all flashing software settings such as MHD, Bm3, etc.* **NOTE: THESE BRACKETS FIT STOCK S55 VC, VTT S55 BILLET VC, and MOST N55 made after 2011. If you have an older N55 made before 01/2011. These may not fit. Purchase carefully as items that have been installed or attempted to cannot be returned.**

Show More Show Less

BMW N55 Turbocharger install kit

2X Entries Into Our F80 M3 Sweepstakes

T#:398463

Part#: VTT-N55-INSTL

Ships in 2 Business Days

$ 222.99 USD

Add to Wish List

Qty

$ 222.99 USD

Add to Wish List

Vargas Turbo has done it again. They've made it even easier for you to get your car back on the road and running right again with your new turbos. They've put together an install kit containing all the components you need to get your new turbos installed properly and efficiently. This means you can get your car back on the road faster and enjoy your new turbos!

Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.

Show More Show Less

VTT N54 Vacuum Pump Block Off Plate

2X Entries Into Our F80 M3 Sweepstakes

T#:11497328

Part#: VTT-N54-VACUUM-B

Ships on Sep 17, 2026

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

Looking to remove the HPFP or DI system on your N54? this plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes Block Plate Note – Plates may come in a clear or anodize black finish depending on stock on hand

Show More Show Less

VTT BMW N54 “DI Injector” Delete Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:11497326

Part#: VTT-N54-DI-DELET

Ships in 2 Business Days

$ 339.99 USD

Add to Wish List

Qty

$ 339.99 USD

Add to Wish List

Looking to get rid of the troublesome and expensive DI injectors on your BMW N54 and move to PI only and a standalone? If so VTT has you covered with its new N54 PI delete kit. This kit allows you to SAFELY remove the DI injectors, install our delete fittings, and run PI only. We machined these deletes from 310 Stainless for extreme heat, and corrosion resistance, and include 3 hold downs. These DI deletes COMPLETELY get rid of all factory provisions, including the seal. If the seal is left intact with no fuel to cool the injector or delete it will quickly overheat and melt the delicate seal causing combustion gasses to escape the engine creating misfires, and worse possibly damaging your injector bore on the cylinder head. Our deletes are machined to be a press fit into the cylinder, and can be either cooled with liquid nitrogen, and dropped in, or tapped in with a hammer, and then held down with the included hold downs. We also include M6 tapped holes on the top of each one in case they need to be removed you can attach a slide hammer, and remove the delete. These are sold as a kit and come with the following 6 – 310 Stainless DI Delete fittings 3 – Hold down brackets Completetion of this kit will require the purchase of HPFP delete plate - ES# 4623950 PLEASE NOTE: THIS KIT REQUIRES EXTENSIVE MODIFICATIONS TO CONVERT YOUR ENGINE TO PI ONLY. THIS INCLUDES BUT IS NOT LIMITED TO A FULL PORT INJECTION SOLUTION, AND STAND-ALONE TO RUN THE PI SYSTEM. WE RECOMMEND THIS PNP SYSTEM USING THE MAXX ECU IT PROVIDES ALL YOU NEED TO GET UP AND RUNNING WITH PI ONLY ON THE TUNING SIDE OF THINGS – https://www.pnpecu.com/pnpecu-maxxecu-n54-pnp-kit-437-p.asp

Show More Show Less

VTT Billet N54/N55 Vacuum/Boost Adapter - Basic Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:600097

Part#: N5455VACADAP-BK

Ships in 6 Business Days

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

The Vacuum Boost Adapter from Vargas Turbos Tehcnologies is an easy way to get a boost source with out having to make irreversible changes to your intake manifold! These go inline to the throttle body and provide a full boost/vacuum signal from the manifold. These are perfect for running your PI off manifold pressure which is much more accurate than charge pipe, and they are also great for BOV running the proper size line without having to drill a hole in your manifold.

Show More Show Less

VTT N54 Billet Vacuum (Boost Control) Tank Kit - Anodized Black - BMW...

2X Entries Into Our F80 M3 Sweepstakes

T#:7530037

Part#: VACUUMCANBLK

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

VTT is proud to offer their billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and use it to regulate boost via the solenoids. The stock plastic can and small plastic nipples on the stock cans have a tendency to crank over time, and if they leak you will get low boost, or no boost, and poor performance. These cans do away with the weak plastic cans while adding some pop, and color to your engine bay. These vacuum cans retain ALL of the factory provisions including mounting points but come with 90-degree fittings for easier routing of the lines VTT's cans are made of 6061-T6 aluminum, and anodized in 4 colors for beauty, and long life. They also knurl the cans for a very distinct look in the engine bay! VTT also designed these cans to complement their N54 Billet lineup – N5X Billet Oil caps, N5XBillet Oil filter housing caps, Billet coolant cap, Billet valve cover, billet oil cooler block off plate, and Billet Power Steering cap, and so on. All will have matching color These cans are offered in 4 colors – Red, Black, Blue, and Clear anodize The kit will include: 2 – Vacuum canisters (color of choice) 4 – billet 90-degree barbed fittings Requires the additional use of aftermarket vacuum line - Vacuum line not included. Replaces Genuine BMW Vacuum Canisters # 11652247620

Show More Show Less

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733531

Part#: VTT-CRANKHUB-5

Ships on Sep 17, 2026

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Billet Check Valve - 10 Barb

2X Entries Into Our F80 M3 Sweepstakes

T#:597641

Part#: VTT-CHECK-2

Ships in 3 Business Days

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

N54 Spline Lock Crank Hub Solution With Complete Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733525

Part#: VTT-CRANKHUB-3

Ships in 6 Business Days

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

BMW N54 3.0L Wastegate Rattle Fix Repair Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:398014

Part#: VTT-N54-WF2

Ships on Sep 18, 2026

$ 95.99 USD

Add to Wish List

Qty

$ 95.99 USD

Add to Wish List

VTT N54 Waste Gate Repair Kit / Rattle Fix Tired of the annoying N54 Wastegate Rattle? Turbos still going strong, but can't deal with the embarrassing rattle anymore? We have the perfect kit for you. This kit comes with 1 set (both turbos) of Stainless Steel wear matched bushing, and flapper assembly, Wastegate arm, rod end, and Stainless steel 8mm C clip. These parts custom made for VTT upgrade the flapper assembly to a full 12.6MM or 1/2" flapper arm, and bushing compared to the stock 11.5mm. They also get rid of the 6mm rod end connection to a full 8mm connection with a stainless steel C clip. There is no better N54 Waste Gate upgrade on the market, and guess what? We also offer them for less than other upgrades which use the stock bushing size, rod end, and inferior materials. If you want to fix this right the first time, this is the kit for you! *Please note, assembly is required. This kit can only be installed with the turbos removed from the vehicle, and stock wastegate assembly removed from the housing. The new assemblies will need to be pressed in, then welded by a qualified welder. We offer no warranty, or returns for improperly installed wastegate assemblies.

Show More Show Less

VTT Billet N54/N55 Vacuum/Boost Adapter - Dual Barb Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:600099

Part#: N5455VACADAP-DB

Ships in 2 Business Days

$ 68.99 USD

Add to Wish List

Qty

$ 68.99 USD

Add to Wish List

The Vacuum Boost Adapter from Vargas Turbos Tehcnologies is an easy way to get a boost source with out having to make irreversible changes to your intake manifold! These go inline to the throttle body and provide a full boost/vacuum signal from the manifold. These are perfect for running your PI off manifold pressure which is much more accurate than charge pipe, and they are also great for BOV running the proper size line without having to drill a hole in your manifold.

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Clear - BMW N52 N...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122266

Part#: VTTFILTERCAPCLR

Ships in 2 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Blue - BMW N52 N5...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122267

Part#: VTTFILTERCAPBLUE

Ships in 5 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

Flapper Delete Fitting - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557962

Part#: VTT-FLAPPER-DELE

Ships on Sep 17, 2026

$ 57.99 USD

Add to Wish List

Qty

$ 57.99 USD

Add to Wish List

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

The VTT PCV Flapper delete is used to get rid of the factory flapper, and add a -10 fitting on N54 powered vehicles. This will allow you to run a single or dual external catch can, or your own custom set up.

This fitting is made from 6061-T6 aircraft aluminum anodized black and comes with O-ring, and a stainless steel holding clip.

This part fits the following BMW engines:
2006-2012 N54

Show More Show Less

VTT N54 Billet Vacuum (Boost Control) Tank Kit - Anodized Red - BMW E...

2X Entries Into Our F80 M3 Sweepstakes

T#:7530038

Part#: VACUUMCANRED

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

VTT is proud to offer their billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and use it to regulate boost via the solenoids. The stock plastic can and small plastic nipples on the stock cans have a tendency to crank over time, and if they leak you will get low boost, or no boost, and poor performance. These cans do away with the weak plastic cans while adding some pop, and color to your engine bay. These vacuum cans retain ALL of the factory provisions including mounting points but come with 90-degree fittings for easier routing of the lines VTT's cans are made of 6061-T6 aluminum, and anodized in 4 colors for beauty, and long life. They also knurl the cans for a very distinct look in the engine bay! VTT also designed these cans to complement their N54 Billet lineup – N5X Billet Oil caps, N5XBillet Oil filter housing caps, Billet coolant cap, Billet valve cover, billet oil cooler block off plate, and Billet Power Steering cap, and so on. All will have matching color These cans are offered in 4 colors – Red, Black, Blue, and Clear anodize The kit will include: 2 – Vacuum canisters (color of choice) 4 – billet 90-degree barbed fittings Requires the additional use of aftermarket vacuum line - Vacuum line not included. Replaces Genuine BMW Vacuum Canisters # 11652247620

Show More Show Less

Vargas Burnt Titanium Magnetic Oil Drain Plug - M12 X 1.5

2X Entries Into Our F80 M3 Sweepstakes

T#:51813315

Part#: VTT-TI-DRAIN

Ships in 6 Business Days

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

The VTT Burnt Titanium Magnetic Oil Drain Plug is a critical upgrade for any performance enthusiast looking to maximize engine longevity.

Extended Spark Plug Socket

T#:391150

Part#: SUU884506

In Stock

9% off MSRP $ 31.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 28.99 USD

Add to Wish List

Qty

9% off MSRP

$ 31.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 28.99 USD

Add to Wish List

3/8" drive socket with 5/8" opening for most spark plugs

VTT N5X/S55/N2X Triple Billet Cap Kit - Red - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122280

Part#: TRIPLECAPRED1

Ships on Sep 18, 2026

$ 209.99 USD

Add to Wish List

Qty

$ 209.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

New N54 Stage 1 turbocharger upgrade 135/535/Z4

2X Entries Into Our F80 M3 Sweepstakes

T#:553008

Part#: VTT-STG-1-NEW-2

Ships on Sep 17, 2026

$ 2,039.99 USD

Add to Wish List

Qty

$ 2,039.99 USD

Add to Wish List

Vargas Stage 1 N54 turbochargers are brand new and include all housing, wheels, and internals. These are brand new units and thus do not require a core charge, making the process easier and simpler. All VTT turbos come with a performance TD04 upgraded thrust to extend the life of the turbochargers. The stock thrust system has shown to be prone to failure and upgraded thrust parts were created to remedy this. The upgraded thrust option consists of an upgraded thrust bearing and a 30% increase in surface area on all complimenting thrust pieces. Every VTT Stage 1 upgrade includes a Billet VTT Compressor wheel. These are fully forged billet wheels, utilizing the ultra-efficient 6×6 blade HTA wheel design as well as extended tip technology to increase airflow a solid 20% over the cast 14T wheels. The use of an aluminum aftermarket charge pipe, and BOV combo is always recommended with upgraded turbos. Add the VTT Cold side Charge pipe, and Turbosmart Raceport BOV to your order for just $349! Please see our BOV article for proper installation to avoid compressor surge! Upgrading your PCV valve is always recommended at the time of turbo upgrade or replacement, as the stock valve can be worn. This means it can stop functioning to its full potential, causing oiling issues with your BMW. This upgraded valve not only replaces the worn stock valve it is also much stronger and will help eliminate any future PCV issues.

Show More Show Less

New N54 Stage 1 Turbocharger Upgrade 135/335/535/Z4

2X Entries Into Our F80 M3 Sweepstakes

T#:397216

Part#: VTT-STG-1-NEW2

Ships in 10 Business Days

Starting at $ 2,039.99 USD

Add to Wish List

Starting at $ 2,039.99 USD

Add to Wish List

BMW N54 3.0L Billet Vaccum Relief Valve

2X Entries Into Our F80 M3 Sweepstakes

T#:597525

Part#: VTT-VAC-RELIEF

Ships in 3 Business Days

$ 104.99 USD

Add to Wish List

Qty

$ 104.99 USD

Add to Wish List

BMW N54 3.0L Billet Vacuum Relief Valve from Vargas Turbo Technologies offers precise control over crankcase vacuum levels. This high-quality billet valve allows users to adjust the vacuum pressure with ease, eliminating guesswork and ensuring optimal engine performance. By simply adding or removing shims, users can tailor the vacuum level to their needs.

Customizable Vacuum Levels: Adjust the vacuum pressure using supplied shims to achieve desired performance.
Direct Fit: Designed with -10ORB threads for easy installation into VTT modular PCV solutions and VTT Modular CNC valve covers.
Versatile Settings: Includes 5 vacuum settings ranging from 10' to 18' of vacuum based on shim configuration.
Enhanced Engine Protection: Helps prevent excessive vacuum that could affect engine seals or cause whistling.

Show More Show Less

Billet 1/2" Check Valve - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557954

Part#: VTT-CHECK-1

Ships in 2 Business Days

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

This is a 1/2" (fits -8AN hos perfectly as well) CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run the vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.

This part fits the following BMW engines:
2006-2012 N54

Show More Show Less

Vargas Oil Feed Adapter - BMW N54

2X Entries Into Our F80 M3 Sweepstakes

T#:51778141

Part#: VTT-N54-OFA

Ships on Sep 17, 2026

$ 41.99 USD

Add to Wish List

Qty

$ 41.99 USD

Add to Wish List

The Vargas Oil Feed Adapter is designed to replace the stock front turbo oil feed line with a robust, CNC-machined solution.

Autel Autolink AL329

T#:2914116

Part#: AL329

Ships in 2 Business Days

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

OBDII Code Reader

N54 Aluminum Turbo Outlet Boost Pipe - 135, 535, 1M, Z4

2X Entries Into Our F80 M3 Sweepstakes

T#:5788175

Part#: VTT-ALUM-OUTLET

Ships on Sep 17, 2026

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

Looking to get the most efficient turbocharger operation out of your N54 powered BMW? The best way to do this is to remove all restrictions from the inlet, and charge tract. The factory charge pipe has a very small 1″ opening and a poorly designed Y section that couples the two banks into one before entering the intercooler. This VTT N54 Aluminum outlet gets rid of those restrictions and provides a full 1.5″ from the turbochargers to a smooth Y transition into a 2.5″ outlet to fit most aftermarket intercoolers. Do not be fooled by companies trying to sell you oversized 2″ charge pipes, these are not going to pick up any power, and will kill velocity. The smallest diameter you can run while still providing adequate flow is always best for flow velocity and reducing time to TQ. This outlet is powder-coated black for a durable finish. The outlet is available in V-band connection for Stock, Stage 1, Stage 2, Stage 2+, any aftermarket turbo that uses the stock connection (RB, Pure, TTE, ETC. It is also available in Hose barb connection for our GC, GC Lite line up., as well as with 1.5″-2″ silicone adapters to fit MMP turbos.

Show More Show Less

Vaico VANOS Camshaft Adjustment Unit Repair Kit - BMW N52 3.0L ...

We Price Match - Give Us A Call or Chat!

T#:34114245

Part#: V20-3674

In Stock

$ 827.99

This product was last offered at the strikethrough price on
05-07-2026

$ 500.99 USD

Add to Wish List

Qty

$ 500.99 USD

Add to Wish List

If your N52 engine is running rough, is low on power, or you are getting check engine lights for timing related issues, there is a good chance that you have a faulty VANOS component. The two most common parts to fail are the Camshaft Adjusters and VANOS Solenoids.

This repair kit from Vaico includes all of the basic parts necessary to service the VANOS system and restore smooth engine operation.

Included:

Intake Camshaft Adjuster w/ Impulse Wheel

Exhaust Camshaft Adjuster w/ Impulse Wheel

Camshaft Adjuster Bolts

VANOS Solenoid Valves

Valve Cover Gasket Set

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Red - BMW N52 N54...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122265

Part#: VTTFILTERCAPRED

In Stock

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Black - BMW N52 N...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122264

Part#: VTTFILTERCAPBLK

Ships on Sep 17, 2026

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

N55 Vargas Stage 1 Turbo Upgrade (New Turbos) (Pneumatic Wastegate) ...

2X Entries Into Our F80 M3 Sweepstakes

T#:390086

Part#: N55-STG1-PWG-NEW

Ships on Sep 17, 2026

$ 1,258.99

This product was last offered at the strikethrough price on
03-09-2026

$ 1,254.00 USD

Add to Wish List

Qty

$ 1,254.00 USD

Add to Wish List

VTT N5X/S55/N2X Triple Billet Cap Kit - Black - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122279

Part#: TRIPLECAPBLK1

Ships on Sep 17, 2026

$ 220.99 USD

Add to Wish List

Qty

$ 220.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

VTT N5X/S55/N2X Triple Billet Cap Kit - Clear - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122281

Part#: TRIPLECAPCLR1

Ships on Sep 17, 2026

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

N54 CHRA Replacement - upgraded td04 thrust assembly - 1/5/Z ...

2X Entries Into Our F80 M3 Sweepstakes

T#:398498

Part#: VTT-N54-CHRA-1-T

Ships on Sep 17, 2026

$ 808.99 USD

Add to Wish List

Qty

$ 808.99 USD

Add to Wish List

Direct OEM replacements with upgraded TD04 thrust assembly - These are a direct replacement for the factory turbocharger. New or reman bearing housing will be used, reman turbine wheel, reman factory compressor wheel. All brand new internals using the upgraded TD04 thrust assembly.

Show More Show Less

135i/535i VTT N54 F-RB+ Turbocharger Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:26504936

Part#: VTT-N54-FRB

Ships on Sep 17, 2026

$ 3,599.99 USD

Add to Wish List

Qty

$ 3,599.99 USD

Add to Wish List

Vargas Ignition Coil Kit (Black) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309609

Part#: VTT-COIL-N5X-BLK

Ships on Sep 17, 2026

$ 167.99 USD

Add to Wish List

Qty

$ 167.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

N55 Stage 1 Turbo Upgrade

2X Entries Into Our F80 M3 Sweepstakes

T#:398009

Part#: N55-STG1

Ships in 10 Business Days

$ 1,545.99

This product was last offered at the strikethrough price on
06-15-2026

Starting at $ 1,541.54 USD

Add to Wish List

Starting at $ 1,541.54 USD

Add to Wish List

Vargas Stage 1 N55 turbo upgrade is good up to 425whp with proper tuning and high grade fuel. Vargas N55 turbo is an all-new turbo specially made for Vargas. They build it with a billet compressor wheel of their own design and a stock turbine. It will accept all of the stock water and oil lines and the original diverter valve (upgraded DV is recommended). This kit is a direct bolt-on replacement for the original turbo and necessary if you want to start making big power from the N55.

The stock plastic diverter valve and chargepipe is the weakest point for boost leaks (the plastic cracks). Vargas Turbo recommends upgrading it to a stronger DV design. The aluminum DV designs will hold up to just about any boost level currently available.

Vargas Turbo Technologies has been in business since 1979, offering rebuilt and re-engineered turbo solutions. For the BMW market, they identified a need for both cost-effective turbo replacements and proven turbo upgrades. It's recommended that the rest of the system be upgraded to handle your tuning goals. The final Vargas rebuilt turbos are better than the factory rebuilds and at a lower cost!

Oil Recommendation - modern engine oil is formulated for emissions and to be environmentally friendly. The additives in current oil lowers the oil's ability to withstand high temperatures and stresses, lowering its shear strength and its lubricating properties. Vargas recommends oils with high ZDDP (zinc and phosphorus) content that will better protect and cool the turbo bearings. Examples of high-zinc oils are Red Line Race, Red Line Euro, Motul 300V Racing, Joe Gibbs Racing, Valvoline VR-1 oil, and most Diesel-spec oils that you can buy off-the-shelf. Some oils, especially the Race type, will need more frequent oil changes and may be harmful to catalytic converters.

WHP rating: 425. This rating is used to compare various stage of Vargas turbo kits. There is no advertised horsepower gain with this kit as it depends on your other mods and tuning. The rating is provided as a reference to use in your tuning planning. Custom tuning is recommended to match thIS turbo to your existing mods and upgrades.

Show More Show Less

N54 CHRA Replacement - upgraded td04 thrust assembly and billet compr...

2X Entries Into Our F80 M3 Sweepstakes

T#:398496

Part#: VTT-N54-CHRA-1TB

Ships on Sep 17, 2026

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Direct OEM replacements with Upgraded TD04 Thrust assembly, and Billet Compressor wheels - These are a direct replacement for the factory turbocharger. New cast bearing housing, reman turbine wheel, Billet 6x6 compressor wheel. All brand new internals using the upgraded TD04 thrust assembly.

Show More Show Less

Spline Lock Crank Hub Solution W/ Hardware Package - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:18733526

Part#: VTT-CRANKHUB-4

Ships on Sep 17, 2026

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW 1 Series E82 (2008-2013)

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results