BMW Engine Parts for BMW 1 Series E82 (2008-2013)

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

This is an OEM INA�mechanical tensioner for the serpentine belt. This tensioner keeps the belt for the alternator, power steering and Air Conditioning taught to provide maximum performance of each system.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. �All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Upgrade your BMW's oil system with the VAC Motorsports N55 Oil Pan Baffle, an essential component for track and street enthusiasts. Engineered to maintain oil surrounding the pick-up at all times, this baffle is crucial for preventing oil pressure loss during hard cornering and acceleration. Trusted by some of the fastest BMWs worldwide, this baffle ensures engine longevity and performance under extreme conditions. Don't risk catastrophic engine failure—equip your BMW with the VAC Motorsports N55 Oil Pan Baffle today.

Benefits:

• Prevents significant loss of oil pressure
• Vital for track and street use
• Ensures engine longevity and performance
• Trusted by high-performance BMWs worldwide

This sensor monitors the position of the Valvetronic eccentric shaft and feeds data back to the ECU. The common issue with this sensor is that it gets contaminated with oil and fails. It doesn't give a fault code or check engine light, however. What you would notice is sluggish driving, hesitation, poor performance, jerky shifts from an automatic, and other drivability issues. These types of issues are typically diagnosed as ignition coils (which are their own issue altogether) but this sensor may also be faulty.

The eccentric shaft sensor is located at the front of the cylinder head and is only accessible with the valve cover off. It's easy to check for oil by removing the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside, or even on the valve cover itself, the sensor is likely contaminated or ready to fail. You can wipe or clean the oil from sitting inside the sensor but it will come back.

If you're planning this job make sure you have our Valve Cover Overhaul Kit, which includes a new seal for the eccentric sensor as well as the rest of the valve cover and Valvetronic gaskets. You can add the valve cover set from the options below.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008+ E82 BMW 128i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2006-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive
2010+ F07 BMW 535i GT, 535i xDrive GT, 550i GT, 550i xDrive GT
2011 F10 BMW 528i
2006-2010 E83 BMW X3 3.0i X3 3.0si
2011 F25 BMW X3 xDrive28i
2007-2010 E70 BMW X5 3.0si X5 xDrive30i
2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive30i

Introducing Turbosmart’s OPR V2 Turbocharger Oil Pressure Regulator, a cutting-edge solution launched in 2022 that ensures steady oil pressure for your turbocharger. This innovative regulator features a return-less design with an integrated 44 Micron Stainless Steel Mesh Oil Filter, providing robust performance and protection.

The OPR V2 is the first of its kind, utilizing Turbosmart’s proprietary flow control method to maintain optimal oil pressure regardless of engine oil variables like pressure or temperature. It guarantees a smooth oil flow to your turbocharger, safeguarding critical components such as Exhaust Drive, Back & Charge Pressures from excessive oil pressure that could lead to oil consumption and smoke.

Gone are the days of guesswork with restrictors and complex plumbing for oil pressure regulation. The OPR V2 simplifies the process with its return-less, inline installation and the convenience of a built-in 44 Micron Oil Filter. This filter, made of serviceable and replaceable Stainless Steel Mesh, adds an extra layer of defense against engine oil debris that could harm your turbocharger.

Key Features:

Innovative Patent Pending Design Durable Aluminium (6262 T6) Anodised Body & Valve Regulated Oil Pressure Compatible with Most turbochargers Integrated Stainless Steel (304) Mesh Oil Filter -4AN Inlet and Outlet for easy installation 1/8 NPT Sensor/Gauge Port for monitoring Directional Inlet Feed Logic for optimized performance Laminar Flow Output for consistent oil delivery Compatible with all Engine Oils Designed and Manufactured in Australia