BMW Engine Parts for BMW 1 Series E82 (2008-2013)

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Continental is the OEM supplier for the stock serpentine accessory belt on your N52 engine.?Over time, accessory belts begin?to wear out and crack. This can lead to the belt slipping, squeaking, or even snapping. Replace your belt on a regular basis to ensure you don't end up stranded on the side of the road with a dead battery or over heated engine due to a bit of simple overlooked maintenance.

Fits the following BMW chassis:
E90 E82/8 E60 E70 E83 E63/64

• 11127582245 - N52 valve cover gasket set
• 11127552280 - N52 eccentric shaft sensor seal
• 11127559699 - N52 Valvetronic gasket

Upgrade your stock oil cooler thermostat for improved performance. Swap out your existing cover with ease, replacing it with a durable billet cover. Upgrade from your 110-degree Celsius thermostat to a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly unlike thermostat bypass kits.

Kit contents:

Billet thermostat housing cover
Replacement gasket
Hardware
Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

This sensor monitors the position of the Valvetronic eccentric shaft and feeds data back to the ECU. The common issue with this sensor is that it gets contaminated with oil and fails. It doesn't give a fault code or check engine light, however. What you would notice is sluggish driving, hesitation, poor performance, jerky shifts from an automatic, and other drivability issues. These types of issues are typically diagnosed as ignition coils (which are their own issue altogether) but this sensor may also be faulty.

The eccentric shaft sensor is located at the front of the cylinder head and is only accessible with the valve cover off. It's easy to check for oil by removing the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside, or even on the valve cover itself, the sensor is likely contaminated or ready to fail. You can wipe or clean the oil from sitting inside the sensor but it will come back.

If you're planning this job make sure you have our Valve Cover Overhaul Kit, which includes a new seal for the eccentric sensor as well as the rest of the valve cover and Valvetronic gaskets. You can add the valve cover set from the options below.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008+ E82 BMW 128i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2006-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive
2010+ F07 BMW 535i GT, 535i xDrive GT, 550i GT, 550i xDrive GT
2011 F10 BMW 528i
2006-2010 E83 BMW X3 3.0i X3 3.0si
2011 F25 BMW X3 xDrive28i
2007-2010 E70 BMW X5 3.0si X5 xDrive30i
2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive30i