BMW Engine Parts for BMW 1 Series E82 (2008-2013)

N-Series Ultimate Performance Ignition Coil - Red - Set Of Six ...

10X Entries Into Our F80 M3 Sweepstakes

T#:23714967

Part#: NSERIESIGNCOILKT

In Stock

$ 205.99 USD

Add to Wish List

Qty

$ 205.99 USD

Add to Wish List

Upgrade your BMW's engine performance with the Dinan Performance Ignition Coil Service Kit. These high-quality ignition coils are crafted to enhance ignition power, ensuring optimal engine performance and efficiency. Engineered for durability and reliability, these coils provide improved throttle response, smoother idle, and enhanced fuel efficiency. Benefit from the Dinan Performance Ignition Coil Service Kit, designed to unleash the true potential of your BMW's engine.

Show More Show Less

N54/N55 Low Temp Oil Thermostat Kit - 70c

10X Entries Into Our F80 M3 Sweepstakes

T#:52621839

Part#: 008731KT1

In Stock

Sale - Save 23% $ 74.98

This product was last offered at the strikethrough price on
05-03-2026

$ 57.74 USD

Add to Wish List

Qty

Sale - Save 23%

$ 74.98

This product was last offered at the strikethrough price on
05-03-2026

$ 57.74 USD

Add to Wish List

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Show More Show Less

N52 Oil Filter Housing Gasket Kit - Includes Oil Pressure Sensor ...

10X Entries Into Our F80 M3 Sweepstakes

T#:15677580

Part#: 11427540759-KT

In Stock

Sale - Save 1% $ 45.99

This product was last offered at the strikethrough price on
05-03-2026

$ 45.34 USD

Add to Wish List

Qty

Sale - Save 1%

$ 45.99

This product was last offered at the strikethrough price on
05-03-2026

$ 45.34 USD

Add to Wish List

This kit includes: 1 Oil Filter Housing Gasket (11428637821) 1 M8x28 bolt (11427540759) 1 M8x43 bolt (11427540763) 1 M8x78 bolt (11427540758) 1 Oil Pressure Sensor (12617568480)

VANOS Solenoid Valve Kit - N52 N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:25805743

Part#: 11367585425TKT

In Stock

Sale - Save 25% $ 150.99

This product was last offered at the strikethrough price on
05-03-2026

$ 112.55 USD

Add to Wish List

Qty

Sale - Save 25%

$ 150.99

This product was last offered at the strikethrough price on
05-03-2026

$ 112.55 USD

Add to Wish List

Failed solenoid valves can lead to numerous issues, such as sluggish acceleration, rough idle, loss of power, limp mode, and check engine lights. Luckily, these issues are easily fixed with our budget-friendly VANOS Solenoid Valve Kit. This kit contains two URO brand VANOS Solenoids, two sets of OEM Elring gaskets, and two Genuine BMW mounting bolts, all for less than the price of a single Genuine BMW Solenoid.

Show More Show Less

N54 Valve Cover Upgrade Kit - BMW N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:25772568

Part#: 11127565284MTKT

In Stock

Sale - Save 23% $ 547.99

This product was last offered at the strikethrough price on
05-03-2026

$ 419.23 USD

Add to Wish List

Qty

Sale - Save 23%

$ 547.99

This product was last offered at the strikethrough price on
05-03-2026

$ 419.23 USD

Add to Wish List

The stock plastic valve cover from BMW tends to warp and crack over time due to numerous heat cycles. This leads to oil and vacuum leaks that both make a mess and negatively affect performance and reliability. Replace your stock valve cover with this aluminum upgrade from Bremmen Parts to eliminate these issues! The aluminum construction results in a significantly stronger valve cover that won't warp or crack. This kit contains everything you need to upgrade your cover, including the upgraded aluminum valve cover, valve cover gasket, oil cap, and hardware. Additionally, we've also included a new PCV blow-by hose and a Vargas PCV upgrade for additional reliability! This is especially important for tuned vehicles with upgraded turbos.

Show More Show Less

ACL 3.0L Standard Size Main Bearing Set BMW N52/N54/N55/S55B30 ...

T#:25706124

Part#: ACL7M1397H-STD

In Stock

$ 256.99 USD

Add to Wish List

Qty

$ 256.99 USD

Add to Wish List

E82 135i N54, E9X 335 N54, E60 535 Vargas Upgraded PCV Valve ...

2X Entries Into Our F80 M3 Sweepstakes

T#:389684

Part#: VTT-N54-PCV

In Stock

$ 68.99 USD

Add to Wish List

Qty

$ 68.99 USD

Add to Wish List

The crankcase oil vent system on the N52/N54 is one of its weakest and cheaply designed systems. We see crankcase vent issues on even stock engines but with more boost the problems are exponential. This Vargas upgraded PCV valve, and an oil catch can, are what the N54 engine needs and may alleviate most of your oil and boost leak issues. The PCV valve is supposed to let oil either return to the oil pan or pass through the intake manifold and get burned up in the combustion chamber. However, BMW used a weak plastic vent valve that doesn't seal well when under boost. Instead of closing and venting the oil out of the intake, it's forced through this valve and into the intake and coating your valves with oil residue and carbon. Most boost equals more oil forcing its way by. This upgraded N54 PCV valve uses higher grade materials, including aluminum, to provide a better seal and prevent oil from entering the intake. It's an easy install and a must-have item when considering any turbo work.

Show More Show Less

BMW E6X / E8X / E9X - N52 Replacement Starter Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15777314

Part#: SR0492NKT2-KT

In Stock

Sale - Save 8% $ 296.99

This product was last offered at the strikethrough price on
03-17-2026

$ 273.79 USD

Add to Wish List

Qty

Sale - Save 8%

$ 296.99

This product was last offered at the strikethrough price on
03-17-2026

$ 273.79 USD

Add to Wish List

Is your car having trouble starting? Does your starter click when you turn the key? Sounds like it's time for a new starter motor! Includes new starter with no core charge, intake gaskets, throttle body gasket and hardware.

Show More Show Less

Accessory Belt Service Kit w/ Kevlar Reinforced Belt - BMW E82/88 E9X...

10X Entries Into Our F80 M3 Sweepstakes

T#:22163422

Part#: 11287568247TKT

Ships on Nov 12, 2026

Sale - Save 15% $ 209.99

This product was last offered at the strikethrough price on
04-15-2026

$ 178.94 USD

Add to Wish List

Qty

Sale - Save 15%

$ 209.99

This product was last offered at the strikethrough price on
04-15-2026

$ 178.94 USD

Add to Wish List

Eliminate your squeaking accessory belt pulley and cracked drive belt with this upgraded accessory belt service kit! This kit includes the ECS Kevlar Reinforced Drive Belt, tensioner assembly, and idler pulleys. ECS Tuning's Red Kevlar Accessory Belts are both an aesthetic improvement and a performance alternative to a traditional belt. Kevlar-reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM-style belts. Refreshing the rollers and/or tensioners simultaneously is a great way to ensure all vital components of your drive belt system are functioning optimally for years to come!

Show More Show Less

BMW N52 Valve Cover & PCV Valve Refresh Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:21735875

Part#: VALVECVRN52KT

Ships in 3 Business Days

Sale - Save 11% $ 465.99

This product was last offered at the strikethrough price on
05-30-2026

$ 412.93 USD

Add to Wish List

Qty

Sale - Save 11%

$ 465.99

This product was last offered at the strikethrough price on
05-30-2026

$ 412.93 USD

Add to Wish List

Maintaining the peak performance and reliability of your BMW N52 engine is essential for a smooth and enjoyable driving experience. One of the most effective ways to achieve this is by replacing critical components like the valve cover, crankcase vent hose, angle connector with heating element, and cylinder sleeve. In this article, we'll delve into the numerous benefits of upgrading these vital parts, ensuring your BMW N52 operates at its best. Optimized Engine Performance: Replacing the valve cover, crankcase vent hose, angle connector, and cylinder sleeve enhances your BMW N52's engine performance. The valve cover plays a crucial role in sealing the engine, preventing oil leaks and ensuring optimal valve operation. When you upgrade these components, you reduce the risk of performance-robbing oil leaks and maintain precise valve timing, resulting in improved horsepower and torque. Enhanced Reliability: Reliability is paramount for any BMW owner. These components, when aged or damaged, can lead to severe engine issues. By replacing them, you significantly reduce the likelihood of unexpected breakdowns or costly repairs, ensuring your BMW N52 engine runs smoothly and reliably for years to come. Improved Fuel Efficiency: An efficiently operating engine not only performs better but also consumes less fuel. The replacement of these components leads to better combustion, reduced emissions, and ultimately improved fuel efficiency. This means fewer trips to the gas station and a lighter environmental footprint. Reduced Maintenance Costs: Regular maintenance and repairs can add up over time. By proactively replacing the valve cover, crankcase vent hose, angle connector, and cylinder sleeve, you mitigate the risk of more extensive engine damage that could lead to expensive repairs down the road. In the long term, this can translate into significant cost savings. Extended Engine Lifespan: The longevity of your BMW N52 engine is directly tied to the quality and condition of its components. When you invest in high-quality replacements, you're effectively extending the lifespan of your engine. This not only preserves the value of your BMW but also allows you to enjoy its performance for years to come. Precise Temperature Control: The angle connector with heating element is vital for maintaining optimal engine temperature, especially in cold weather. A malfunctioning or worn-out connector can disrupt temperature control, affecting engine performance. Replacing this component ensures consistent and precise temperature management. Customized Upgrades: When replacing these components, you have the opportunity to choose high-performance or specialized alternatives, allowing you to customize your BMW N52 to your preferences. Whether you prioritize power, efficiency, or specific driving conditions, there are options available to tailor your engine's performance accordingly. Included in the BMW N52 Valve Cover & PCV Valve Refresh Kit: 6 Cylinder Sleeves 1 Alternator Mounting Screw Set 1 Angle Connector with Heating Element 1 Valve Cover - Gasket Included 1 Crankcase Vent Hose

Show More Show Less

70c Low Temp Oil Thermostat Kit - N54/N55

10X Entries Into Our F80 M3 Sweepstakes

T#:30031507

Part#: N54N55LTKT1

Back Ordered

Sale - Save 18% $ 152.97

This product was last offered at the strikethrough price on
05-03-2026

$ 125.58 USD

Add to Wish List

Qty

Sale - Save 18%

$ 152.97

This product was last offered at the strikethrough price on
05-03-2026

$ 125.58 USD

Add to Wish List

Upgrade your stock oil cooler thermostat for improved performance. Swap out your existing cover with ease, replacing it with a durable billet cover. Upgrade from your 110-degree Celsius thermostat to a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly unlike thermostat bypass kits.

Kit contents:

Billet thermostat housing cover
Replacement gasket
Hardware
Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Show More Show Less

Rod Bearing Replacement Kit - E9X E82/88 N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:24145933

Part#: E9XN54RBRLMKT

In Stock

Sale - Save 2% $ 467.99

This product was last offered at the strikethrough price on
08-31-2026

$ 457.48 USD

Add to Wish List

Qty

Sale - Save 2%

$ 467.99

This product was last offered at the strikethrough price on
08-31-2026

$ 457.48 USD

Add to Wish List

This kit includes everything needed to replace your rod bearings. Kit includes Upper and lower road bearings Hardware Oil filter Molygen New Generation Engine Oil (5w-40) - 7 Liters Oil pan gasket RedLine assembly lube

Show More Show Less

N54 AC Delete Accessory Belt Kit - BMW N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:26771665

Part#: 7PK1660KT

In Stock

Sale - Save 13% $ 75.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.28 USD

Add to Wish List

Qty

Sale - Save 13%

$ 75.99

This product was last offered at the strikethrough price on
05-03-2026

$ 66.28 USD

Add to Wish List

This AC Delete Accessory Belt Kit includes a new idler pulley and a shorter ECS Kevlar belt for deleting your AC compressor. ECS Tuning Performance Kevlar reinforced belts give you that extra piece of mind! Kevlar-reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM-style belts. Tensile strength Elongation Hardness Temperature and oil resistance per standard JASO E 109-94 Flex testing per SAE J2432

Show More Show Less

VTT N54 Billet Vacuum (Boost Control) Tank Kit - Anodized Blue - BMW ...

2X Entries Into Our F80 M3 Sweepstakes

T#:7530040

Part#: VACUUMCANBLUE

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

VTT is proud to offer their billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and use it to regulate boost via the solenoids. The stock plastic can and small plastic nipples on the stock cans have a tendency to crank over time, and if they leak you will get low boost, or no boost, and poor performance. These cans do away with the weak plastic cans while adding some pop, and color to your engine bay. These vacuum cans retain ALL of the factory provisions including mounting points but come with 90-degree fittings for easier routing of the lines VTT's cans are made of 6061-T6 aluminum, and anodized in 4 colors for beauty, and long life. They also knurl the cans for a very distinct look in the engine bay! VTT also designed these cans to complement their N54 Billet lineup – N5X Billet Oil caps, N5XBillet Oil filter housing caps, Billet coolant cap, Billet valve cover, billet oil cooler block off plate, and Billet Power Steering cap, and so on. All will have matching color These cans are offered in 4 colors – Red, Black, Blue, and Clear anodize The kit will include: 2 – Vacuum canisters (color of choice) 4 – billet 90-degree barbed fittings Requires the additional use of aftermarket vacuum line - Vacuum line not included. Replaces Genuine BMW Vacuum Canisters # 11652247620

Show More Show Less

VTT Billet Power Steering Pulley - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:7292042

Part#: VTT-N54-PSN54

Ships in 2 Business Days

Starting at $ 56.99 USD

Add to Wish List

Starting at $ 56.99 USD

Add to Wish List

Vargas has introduced their new Billet Power Steering pulleys for the N54 engine! A well-known issue with the N54 with Hydraulic power steering is the plastic pulley either hitting the subframe, or breaking on its own. This can result in the belt to be ejected from the pulley, and leave you stranded with no serpentine belt. This also increases the chance of sucking the belt into the engine through the front seal. Put an end to the dreaded plastic PS pulley issues with the VTT 100% Billet Aluminum PS pulley. These are constructed from 6061-T6 aluminum and anodize in one of 4 colors (Black, Red, Blue, and Clear) for a great look, and long-lasting finish. These weigh 11oz, very close to the weight of a stock pulley, and are lighter than the cast aluminum versions on the market.

Show More Show Less

Performance Rod Bearing Replacement Kit - N55 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:36032373

Part#: N55-WPC-RBKT2

In Stock

Sale - Save 6% $ 844.90

This product was last offered at the strikethrough price on
05-03-2026

$ 790.38 USD

Add to Wish List

Qty

Sale - Save 6%

$ 844.90

This product was last offered at the strikethrough price on
05-03-2026

$ 790.38 USD

Add to Wish List

This kit includes every thing needed to replace your rod bearings.

Kit includes

Upper and lower WPC-treated rod bearings Hardware Oil filter BMW TwinPower Turbo Oil Oil pan gasket RedLine assembly lube

Show More Show Less

Accessory Belt Service Kit w/ Kevlar Reinforced Belt - BMW N52 ...

10X Entries Into Our F80 M3 Sweepstakes

T#:22130432

Part#: 11287530314TKT

In Stock

Sale - Save 18% $ 127.99

This product was last offered at the strikethrough price on
05-03-2026

$ 104.71 USD

Add to Wish List

Qty

Sale - Save 18%

$ 127.99

This product was last offered at the strikethrough price on
05-03-2026

$ 104.71 USD

Add to Wish List

Eliminate your squeaking accessory belt pulley and cracked drive belt with this upgraded accessory belt service kit! This kit includes the ECS Kevlar Reinforced Drive Belt, tensioner assembly, and idler pulley. ECS Tuning's Red Kevlar Accessory Belts are both an aesthetic improvement and a performance alternative to a traditional belt. Kevlar-reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM-style belts. Refreshing the rollers and/or tensioners simultaneously is a great way to ensure all vital components of your drive belt system are functioning optimally for years to come!

Show More Show Less

VTT Ignition Coil Conversion Kit - S55/N55 To B58 - Multiple Color Op...

2X Entries Into Our F80 M3 Sweepstakes

T#:22196341

Part#: VTTS55CLCNV

Ships in 9 Business Days

Starting at $ 335.99 USD

Add to Wish List

Starting at $ 335.99 USD

Add to Wish List

VTT is proud to offer its very own Game Changer S55/N55 to B58 Coil conversion kit for the BMW S55/N55 platforms. The 55 series of engines has notoriously had ignition problems with the factory coils, while aftermarket upgrades do exist, they can be bulky. The solution is the BMW B58 ignition coils which are extremely robust and can support well over 1000WHP with no issues. This means a plug-and-play affordable solution that fits like stock, and looks AMAZING doing so! We designed our own 6061-T6 Billet bracket in a plethora of colors including matching shades for every S55/N55 Valve Cover. This means you can mix and match the color of the bracket with coil color, with VC color to truly tailor your engine bay to look exactly how you want it to! The kit comes with the following: 3 – Billet Aluminum Coil Brackets in the color of choice 6 – Plug and play VTT wiring harnesses 6 – Custom VTT stalks to convert the B58 coils to the S55/N55 head (We ensure proper spring length inside the boot for optimal spring-to-plug contact) *NOTE: Flash setting changes may be required when installing the conversion kit to ensure the proper function of the B58 coils with S55/N55 DME. This can be found in almost all flashing software settings such as MHD, Bm3, etc.* **NOTE: THESE BRACKETS FIT STOCK S55 VC, VTT S55 BILLET VC, and MOST N55 made after 2011. If you have an older N55 made before 01/2011. These may not fit. Purchase carefully as items that have been installed or attempted to cannot be returned.**

Show More Show Less

Dry N55 Rod Bearing Replacement Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:40782380

Part#: N55RODBRGDRYKT

In Stock

Sale - Save 3% $ 399.64

This product was last offered at the strikethrough price on
05-03-2026

$ 389.08 USD

Add to Wish List

Qty

Sale - Save 3%

$ 399.64

This product was last offered at the strikethrough price on
05-03-2026

$ 389.08 USD

Add to Wish List

This kit includes everything needed to replace the rod bearings in your N55 engine other than the engine oil and assembly lube. Kit includes Upper and lower rod bearings Hardware Oil filter Oil pan gasket

Show More Show Less

N55 Rod Bearing Replacement Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:23913954

Part#: N55RODBRGKT

In Stock

$ 510.62 USD

Add to Wish List

Qty

$ 510.62 USD

Add to Wish List

This kit includes everything needed to replace the rod bearings in your N55 engine. Kit includes Upper and lower rod bearings Hardware Oil filter BMW TwinPower Turbo Oil Oil pan gasket RedLine assembly lube

Show More Show Less

N54 Turbocharger Installation Kit - Front And Rear

10X Entries Into Our F80 M3 Sweepstakes

T#:15511873

Part#: 114275634530KT

Ships in 8 Business Days

Sale - Save 12% $ 299.95

This product was last offered at the strikethrough price on
05-03-2026

$ 264.60 USD

Add to Wish List

Qty

Sale - Save 12%

$ 299.95

This product was last offered at the strikethrough price on
05-03-2026

$ 264.60 USD

Add to Wish List

Ensure proper sealing when installing the turbos on your N54. Kit includes: 16 - ASA M7x39 studs 16 - Flange nuts All required gaskets and o-rings Water pump install hardware Replacement vacuum hose T-bolt clamps Helpful hints: For complete installation instructions, refer to Haynes Service Manual (ES2500921). Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal. If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side. To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well. Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced. Torque specs: Bracket to cylinder head: 9Nm Coolant supply line to crankcase: 9Nm Coolant return line to crankcase: 8Nm Coolant return line to turbo: 8Nm Coolant supply line to supply line: 8Nm Exhaust manifold heat shield: 8Nm Oil supply line to crankcase: 20Nm Oil pressure line to turbo: 8Nm Oil return line to crankcase: 8Nm Oil return line to turbo: 8Nm Turbo manifold to head: 20Nm

Show More Show Less

Cam Bearing Ledge Replacement Kit - BMW N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:23748158

Part#: 11127531224TKT

Ships in 2 Business Days

$ 1,650.31 USD

Add to Wish List

Qty

$ 1,650.31 USD

Add to Wish List

Have your camshaft bearing ledges seen better days? This kit includes everything needed to replace your cam bearing ledges with Genuine BMW and high-quality OEM components. Included in this kit: Intake Cam Bearing Ledge Exhaust Cam Bearing Ledge Valve Cover Gasket Timing Chain Tensioner Cylinder Head Hardware Assembly Lubricant BMW Engine Oil Hengst Oil Filter

Show More Show Less

AutoTecknic Dry Carbon Competition Oil Cap Cover - Type 1 - For Vario...

T#:39971047

Part#: BM-0007

In Stock

$ 64.99 USD

Add to Wish List

Qty

$ 64.99 USD

Add to Wish List

a precision-engineered, lightweight dry carbon fiber upgrade designed to enhance the engine bay of compatible BMW models with an aggressive motorsport look and easy OEM-style installation.

Top-Tier BMW N54/N55 Ignition Service Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:21670137

Part#: TMSN5SPCOILKT

In Stock

Sale - Save 13% $ 285.99

This product was last offered at the strikethrough price on
05-03-2026

$ 248.31 USD

Add to Wish List

Qty

Sale - Save 13%

$ 285.99

This product was last offered at the strikethrough price on
05-03-2026

$ 248.31 USD

Add to Wish List

Upgrade your BMW N54 and N55 engine with Packaged by Turner kits for optimized performance and fuel efficiency. Our BMW ignition coils feature specialized modifications to boost firepower, delivering increased torque at lower RPMs and more horsepower at higher RPMs. The extent of improvement depends on your engine's current condition, but you'll undoubtedly experience a noticeable difference in performance. Ensure your BMW's engine runs smoothly and efficiently with our comprehensive ignition service kit from ECS Tuning. This kit includes six Bav Auto ignition coils with plug boots, NGK spark plugs, American Grease Stick dielectric grease, and a BMW spark plug service indicator label. Rest assured with a 2-year warranty on all Bavarian Autosport brand parts. Upgrade your BMW N54 and N55 engine's ignition system today for a remarkable driving experience.

Show More Show Less

N54T/"is" Engine & Transmission Mount Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:42099844

Part#: 22116793240TKT

Ships in 2 Business Days

$ 387.99

This product was last offered at the strikethrough price on
05-06-2026

$ 380.99 USD

Add to Wish List

Qty

$ 380.99 USD

Add to Wish List

Whether you're building a dedicated track car or upgrading your street BMW, the N54T/"is" Engine & Transmission Mount Kit is an essential component for maximizing drivetrain performance and reliability.

Show More Show Less

Turbo Coolant Line Kit - E60, E82, E88

10X Entries Into Our F80 M3 Sweepstakes

T#:42099865

Part#: 11537558900TKT

In Stock

Sale - Save 23% $ 253.99

This product was last offered at the strikethrough price on
05-03-2026

$ 194.66 USD

Add to Wish List

Qty

Sale - Save 23%

$ 253.99

This product was last offered at the strikethrough price on
05-03-2026

$ 194.66 USD

Add to Wish List

Prevent overheating issues and protect your turbo system with the Turbo Coolant Line Kit, the complete solution for keeping your N54 engine running at peak performance.

Basic High Pressure Fuel Pump Replacement Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15644266

Part#: 13517616170-KT

In Stock

$ 1,678.35

This product was last offered at the strikethrough price on
06-19-2026

$ 1,677.85 USD

Add to Wish List

Qty

$ 1,677.85 USD

Add to Wish List

HPFP woes? Replacement high pressure exchange pump for the N54 engine. Kit includes: Remanufactured High-pressure fuel pump Intake manifold gasket sets Throttle body gasket

Valvetronic Camshaft Adjuster replacement kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15677492

Part#: 11127556161-KT

In Stock

Sale - Save 19% $ 220.99

This product was last offered at the strikethrough price on
05-03-2026

$ 179.28 USD

Add to Wish List

Qty

Sale - Save 19%

$ 220.99

This product was last offered at the strikethrough price on
05-03-2026

$ 179.28 USD

Add to Wish List

Valv-tronic adjuster unit, Changes the the timing shaft to adjust the valve timing.

Accessory Belt Service Kit w/ Kevlar Reinforced Belt - BMW E82/88 E9X...

10X Entries Into Our F80 M3 Sweepstakes

T#:22163417

Part#: 11287582946TKT

Ships on Nov 12, 2026

$ 223.76 USD

Add to Wish List

Qty

$ 223.76 USD

Add to Wish List

Eliminate your squeaking accessory belt pulley and cracked drive belt with this upgraded accessory belt service kit! This kit includes the ECS Kevlar Reinforced Drive Belt, belt tensioner, and idler pullies. ECS Tuning's Red Kevlar Accessory Belts are both an aesthetic improvement and a performance alternative to a traditional belt. Kevlar-reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM-style belts. Refreshing the rollers and/or tensioners simultaneously is a great way to ensure all vital components of your drive belt system are functioning optimally for years to come!

Show More Show Less

Liqui Moly Longtime High Tech Oil Change Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15644259

Part#: 07119963129-KT

Ships in 2 Business Days

Sale - Save 7% $ 115.98

This product was last offered at the strikethrough price on
08-31-2026

$ 107.95 USD

Add to Wish List

Qty

Sale - Save 7%

$ 115.98

This product was last offered at the strikethrough price on
08-31-2026

$ 107.95 USD

Add to Wish List

To keep your driving machine in top shape, regular maintenance is imperative. BMW's service interval for an oil change varies based on driving habits. We recommend changing your oil after no more than 10,000 miles. A 5,000 oil service interval is preferred for aggressive or city driving. This kit contains Seven Liters of Liqui Moly Longtime High Tech Engine Oil 5w-30 Engine Oil Filter Oil Drain Plug Gasket (Included with filter kit)

Show More Show Less

Eccentric Shaft Replacement Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:22789670

Part#: S55SHAFTRPCKT

In Stock

$ 1,209.99

This product was last offered at the strikethrough price on
08-24-2026

$ 1,208.99 USD

Add to Wish List

Qty

$ 1,208.99 USD

Add to Wish List

Ensure the peak performance of your BMW N55 or S55 engine with Turner Motorsport's Eccentric Shaft Replacement Kit. This all-inclusive kit features essential components, including:

Camshaft
Eccentric Shaft Bearing
Valve Cover Gasket Set
Gasket

Designed for precision and durability, this kit guarantees optimal engine performance and longevity. Rely on Turner Motorsport for top-quality replacement parts that adhere to the highest standards.

Show More Show Less

Wastegate Repair Kit - N54

10X Entries Into Our F80 M3 Sweepstakes

T#:41863724

Part#: 116575857456TKT

Ships on Sep 18, 2026

$ 164.99 USD

Add to Wish List

Qty

$ 164.99 USD

Add to Wish List

Get rid of that annoying N54 Wastegate Rattle for good!

Fuel Injector Replacement Kit - N52

10X Entries Into Our F80 M3 Sweepstakes

T#:53044116

Part#: 13537531634RKT2

Ships on Oct 15, 2026

Sale - Save 22% $ 318.99

This product was last offered at the strikethrough price on
05-03-2026

$ 247.50 USD

Add to Wish List

Qty

Sale - Save 22%

$ 318.99

This product was last offered at the strikethrough price on
05-03-2026

$ 247.50 USD

Add to Wish List

Restore engine performance and drivability by replacing those old, high mileage fuel injectors. Includes injector clips.

Oil Filter Housing Gasket Kit - N52 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:24212294

Part#: N52OFHGKT

In Stock

Sale - Save 3% $ 138.99

This product was last offered at the strikethrough price on
06-15-2026

$ 134.82 USD

Add to Wish List

Qty

Sale - Save 3%

$ 138.99

This product was last offered at the strikethrough price on
06-15-2026

$ 134.82 USD

Add to Wish List

A leaking gasket can cause headaches down the road, usually when you least expect it. The N52 engine can suffer a particularly troublesome leak around the oil filter housing gasket. Generally seen as something to keep an eye on, this is not something that should be put off. The upgraded Bavarian Autosport gasket is made from a DuPont Viton rubber that has a higher temperature and chemical resistance than the stock gasket material. This gasket should last the lifetime of the engine without breaking down and leaking like the Genuine BMW parts do.

Show More Show Less

Bosch Starter Motor With Hardware

10X Entries Into Our F80 M3 Sweepstakes

T#:56110332

Part#: SR0492NKT4

In Stock

$ 273.99

This product was last offered at the strikethrough price on
08-14-2026

$ 261.99 USD

Add to Wish List

Qty

$ 261.99 USD

Add to Wish List

At the core is a brand-new Bosch Starter Motor, engineered to withstand extreme operating conditions while delivering immediate cranking speed. This kit includes also the required Genuine BMW Aluminum Mounting Screw Set.

Show More Show Less

AutoTecknic - Carbon Competition Fuel Cap Cover - Various BMW and MIN...

T#:39971046

Part#: BM-0006-BCG

In Stock

$ 65.00 USD

Add to Wish List

Qty

$ 65.00 USD

Add to Wish List

AutoTecknic - Carbon Competition Fuel Cap Cover - Various BMW and MINI Models is a premium exterior upgrade crafted from genuine carbon fiber, designed to enhance the aggressive styling and performance aesthetic of compatible BMW and MINI vehicles with an easy, OEM-fit installation.

Show More Show Less

BMW E6X / E8X / E9X / Z4 Cam Bearing Ledge Replacement Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:21703017

Part#: N54CAMBRINGKT

Ships in 2 Business Days

$ 1,650.31 USD

Add to Wish List

Qty

$ 1,650.31 USD

Add to Wish List

Maintaining your BMW E6X, E8X, E9X, or Z4 engine health is paramount to ensure optimal performance and longevity. Two crucial components that require periodic attention are the cam bearing ledge and valve cover gasket. Regular servicing of these components, along with other critical elements such as the camshaft O-ring, chain tensioner (with gasket), and oil filter, is imperative to keep your BMW running smoothly. Included in Kit: 1 - Cam Bearing Ledge - Exhaust 29 - Torx Bolt 1 - Genuine Cam Bearing Ledge - Intake 1 - Genuine Cam Bearing Ledge - Exhaust 1 - Valve Cover Gasket 4 - Genuine Camshaft O-rings 7 - Genuine BMW TwinPower Turbo 5W-30 Engine Oil 1 - Assembly Lube 1 - Chain Tensioner - With Gasket Ring 1 - Hengst Oil Filter 2 - Collar Screws Cam Bearing Ledge: The cam bearing ledge is vital for proper camshaft support and lubrication. Over time, wear and tear can compromise its effectiveness, potentially leading to camshaft damage. Servicing this component ensures that your camshaft operates optimally, preventing costly repairs. Valve Cover Gasket: A well-maintained valve cover gasket is essential to prevent oil leaks and maintain proper sealing in the engine. Ignoring gasket issues can lead to oil contamination, loss of engine performance, and even engine damage. Camshaft O-Ring: The camshaft O-ring helps maintain proper oil pressure and prevents oil leakage. A deteriorated O-ring can result in oil seepage, leading to lubrication issues that affect engine performance and longevity. Chain Tensioner (with Gasket Ring): Proper timing chain tension is crucial for engine synchronization. Servicing the chain tensioner and its gasket ensures correct timing, preventing potential engine misfires and damage. Oil Filter: Regularly replacing the oil filter is fundamental to maintaining clean engine oil. Clean oil is essential for lubrication and heat dissipation, safeguarding the engine against wear and tear. Kit is for these BMW models: E60 / E61 - N54 3.0L E82 / E88 - N54 3.0L E90 / E92 / E93 - N54 3.0L Z4 - N54 3.0L

Show More Show Less

Boost Solenoid/Pressure Converter - Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15677490

Part#: 11721439973-KT

In Stock

Sale - Save 45% $ 408.99

This product was last offered at the strikethrough price on
07-14-2026

$ 226.02 USD

Add to Wish List

Qty

Sale - Save 45%

$ 408.99

This product was last offered at the strikethrough price on
07-14-2026

$ 226.02 USD

Add to Wish List

Kit includes both boost solenoids, vacuum hose and T fitting for a easy leak free install

Oil Filter Housing Gasket Replacement Kit - BMW N54 N55 3.0L ...

10X Entries Into Our F80 M3 Sweepstakes

T#:24344808

Part#: N54OFHGKT

In Stock

Sale - Save 1% $ 171.99

This product was last offered at the strikethrough price on
08-18-2026

$ 171.09 USD

Add to Wish List

Qty

Sale - Save 1%

$ 171.99

This product was last offered at the strikethrough price on
08-18-2026

$ 171.09 USD

Add to Wish List

If you have a leaking oil filter housing seal, why not replace it while doing an oil service? This kit includes an Oil service kit along with an oil filter housing gasket and thermostat housing gasket.

Show More Show Less

Ignition Service Kit

10X Entries Into Our F80 M3 Sweepstakes

T#:15677540

Part#: 12138616153-KT

Ships in 3 Business Days

$ 240.99

This product was last offered at the strikethrough price on
07-27-2026

$ 217.99 USD

Add to Wish List

Qty

$ 217.99 USD

Add to Wish List

If your BMW's mileage is getting up there, be sure to keep your ignition system in check. Whether you currently have a misfire or you're just doing preventative maintenance, this kit is perfect. The kit includes: 6 Coils with locks 6 spark plugs BMW spark plug service label for your records 1 packet of American Grease Stick dielectric grease

Show More Show Less

Ignition Service Kit - E9x, E82, E88, E70, E83

10X Entries Into Our F80 M3 Sweepstakes

T#:41425001

Part#: 12138616153T1KT

In Stock

$ 269.99 USD

Add to Wish List

Qty

$ 269.99 USD

Add to Wish List

Comes with coil packs, dialectic grease and spark plugs for an all inclusive kit for servicing your BMW!

Genuine BMW Oil Change Kit / Inspection I - N52, N54, N55

10X Entries Into Our F80 M3 Sweepstakes

T#:15511870

Part#: 832123659460KT

In Stock

Sale - Save 3% $ 123.99

This product was last offered at the strikethrough price on
08-31-2026

$ 119.91 USD

Add to Wish List

Qty

Sale - Save 3%

$ 123.99

This product was last offered at the strikethrough price on
08-31-2026

$ 119.91 USD

Add to Wish List

This oil change kit has everything you need for an easy oil change, including seven liters of oil, an oil filter, and a drain plug.

Elring Oil Pan Gasket And CRP Hardware Set

10X Entries Into Our F80 M3 Sweepstakes

T#:56218592

Part#: 1137548031ELRKT2

In Stock

$ 82.99 USD

Add to Wish List

Qty

$ 82.99 USD

Add to Wish List

This Oil Pan Refresh Kit pairs a high tier Elring sealing gasket with the complete factory spec aluminum bolt set required for proper reassembly.

Genuine BMW Oil Pan Gasket With Oil Pan Bolt Set - N55

10X Entries Into Our F80 M3 Sweepstakes

T#:56038085

Part#: 11137600482KT4

In Stock

$ 130.99 USD

Add to Wish List

Qty

$ 130.99 USD

Add to Wish List

This Hardware & Gasket Refresh Kit takes the guesswork out of maintenance. This kit bundles a high quality replacement oil pan gasket with a fresh, complete set of factory spec aluminum hardware. Whether you are dropping the subframe for a preventative overhaul or chasing down an active oil leak

Show More Show Less

High Pressure Fuel Pump Replacement Kit - N55 E Chassis

10X Entries Into Our F80 M3 Sweepstakes

T#:15644274

Part#: 13517616170KT

In Stock

$ 1,783.31

This product was last offered at the strikethrough price on
07-06-2026

$ 1,743.13 USD

Add to Wish List

Qty

$ 1,743.13 USD

Add to Wish List

This extensive kit includes a HPFP and associated gaskets to get the job done right!

Rod Bearing Replacement Kit - E9X E82/88 N54 3.0L

10X Entries Into Our F80 M3 Sweepstakes

T#:24145934

Part#: E9XN54RBRKT

In Stock

$ 521.23 USD

Add to Wish List

Qty

$ 521.23 USD

Add to Wish List

This kit includes everything needed to replace your rod bearings. Kit includes Upper and lower road bearings Hardware Oil filter BMW TwinPower Turbo Oil Oil pan gasket RedLine assembly lube

Show More Show Less

Oil Pan Gasket - With Bolts

10X Entries Into Our F80 M3 Sweepstakes

T#:15644297

Part#: 11132210959-KT

In Stock

Sale - Save 3% $ 81.99

This product was last offered at the strikethrough price on
05-03-2026

$ 79.42 USD

Add to Wish List

Qty

Sale - Save 3%

$ 81.99

This product was last offered at the strikethrough price on
05-03-2026

$ 79.42 USD

Add to Wish List

A common piece to begin leaking on any engine, oil pan gaskets begin to leak after a few years.

Eccentric Shaft Replacement Kit - N55/S55

10X Entries Into Our F80 M3 Sweepstakes

T#:21735862

Part#: CAMGSKTN55S55KT

In Stock

$ 1,209.99

This product was last offered at the strikethrough price on
08-24-2026

$ 1,208.99 USD

Add to Wish List

Qty

$ 1,208.99 USD

Add to Wish List

When it comes to optimizing the performance and longevity of your BMW N55 or S55 engine, few upgrades can rival the impact of replacing the camshaft, bearings, and gaskets. These essential components play a pivotal role in your engine's overall health and performance, and upgrading them can deliver a host of benefits, from increased power to enhanced reliability. In this article, we'll explore the advantages of investing in these critical upgrades for your BMW N55 or S55 engine. Improved Performance: Upgrading your BMW N55 or S55 engine with a new camshaft can significantly boost its performance. A high-quality camshaft can optimize valve timing, leading to improved airflow and combustion efficiency. This, in turn, results in increased horsepower and torque, providing you with a more exhilarating driving experience. If you're seeking that extra punch when you hit the gas pedal, a new camshaft is the way to go. Enhanced Durability: The camshaft, bearings, and gaskets are fundamental components of your engine's internal structure. Over time, wear and tear can cause these parts to degrade, potentially leading to catastrophic engine failure. By replacing these components with high-quality, performance-oriented alternatives, you're not only increasing horsepower but also reinforcing the engine's durability. This can help prevent costly breakdowns and extend the life of your BMW engine. Optimal Efficiency: Efficiency is a key factor in engine performance. Worn-out bearings and gaskets can lead to oil leaks and reduced engine efficiency. Replacing them ensures a tighter seal, minimizing oil leaks and maintaining the proper lubrication for all moving parts. This leads to better fuel efficiency and a smoother, more reliable engine operation, all while reducing maintenance costs in the long run. Increased Resale Value: Investing in high-quality components like camshafts, bearings, and gaskets not only enhances your driving experience but also adds value to your BMW. When it's time to sell or trade-in your vehicle, potential buyers or dealerships will recognize the value of these upgrades, making your car more desirable and potentially increasing its resale value. Kit for All N55/S55 Engines

Show More Show Less

Rod Bearing Replacement Kit - E9x, E82, E88

10X Entries Into Our F80 M3 Sweepstakes

T#:42133543

Part#: 11247589671TKT

Back Ordered

Sale - Save 2% $ 563.99

This product was last offered at the strikethrough price on
05-15-2026

$ 550.86 USD

Add to Wish List

Qty

Sale - Save 2%

$ 563.99

This product was last offered at the strikethrough price on
05-15-2026

$ 550.86 USD

Add to Wish List

Whether addressing rod bearing noise or performing preventative maintenance, this kit ensures optimal engine health, reducing the risk of costly repairs.