BMW Engine Parts for BMW 1 Series E82 (2008-2013)

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

2X Entries Into Our F80 M3 Sweepstakes

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Precision Raceworks Bucketed Low-Pressure Fuel Pump Kit - Stage 2 - B...

T#:1331979

Part#: 601-0176

In Stock

$ 419.99 USD

Add to Wish List

Qty

$ 419.99 USD

Add to Wish List

When upgrading your turbos or increasing your BMW's power potential, it's important not to overlook your fuel pump. Both low and high-pressure fuel pumps can only flow so much fuel, limiting power potential regardless of turbo size or other power adders, especially when running an ethanol blend. Upgrade your BMW fuel pump with Precision Raceworks' Low-Pressure Bucketed Fuel Pump Kits. Precision's low-pressure fuel pumps are designed to flow significantly more fuel than your BMW's stock system, ideal for customers who are upgrading their vehicles or plan to run blended fuel or E85 alone! This is a true plug-and-play solution that anyone can install in their home garage and start taking advantage of the benefits right away. Precision Raceworks' Stage 2 bucketed fuel pump kit includes a genuine Walbro 450 (F90000274) fuel pump, capable of supporting up to 575whp on 93 octane pump gas or 500whp on 100% E85! In order to prevent having to send in your fuel pump, each of Precision Raceworks' kits includes thorough instructions and all of the items required to assemble your kit at home. This prevents delays in shipping, potential damage to your stock fuel pump housing, and reduces assembly costs to keep prices low. It also improves installation as there is no guesswork on engagement and sealing of o-ring or complications and risks of tightening clamps that can poke holes in critical plastic components nearby. While all bucketless fuel pumps flow .2gpm more than a bucket design that retains the venturi, it comes at a cost. Bucketless pumps should not be driven on tanks lower than 1/4 full and should not be used for road course racing. This is not a disadvantage of only bucketless designs, but also a disadvantage for any bucket design which deletes the venturi. If you do not plan on road course or drag racing (not street racing) and are responsible at maintaining 1/4 tank of fuel during spirited driving, bucketless pumps can be a cheaper alternative for you.

Show More Show Less

BMW Oil Cap Crankcase Breather - All BMW w/2 prong oil fill cap ...

2X Entries Into Our F80 M3 Sweepstakes

T#:558084

Part#: VTT-CRANK-BREATH

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Show More Show Less

Precision Raceworks Ethanol 360 Fittings - 5/16" (7.89mm)

Universal Product - Please confirm your fuel line size prior to ordering

T#:37757295

Part#: 601-0240

Ships in 5 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

The Precision Raceworks Ethanol 360 fuel line fittings are designed to work in almost any application where you have 5/16" or 7.89mm quick-connect fittings and need to add a flex fuel sensor. These fittings work with almost all ethanol sensors without the need to cut and splice or replace entire line sets. This is a perfect way to add an ethanol sensor to your vehicle while maintaining existing fuel lines.

Show More Show Less

Bucketed Low-Pressure Fuel Pump Kit - Stage 2.5v2 - BMW E9X E8X ...

T#:1165728

Part#: 601-0177

In Stock

$ 494.99 USD

Add to Wish List

Qty

$ 494.99 USD

Add to Wish List

When upgrading your turbos or increasing your BMW's power potential, it's important not to overlook your fuel pump. Both low and high-pressure fuel pumps can only flow so much fuel, limiting power potential regardless of turbo size or other power adders, especially when running an ethanol blend. Upgrade your BMW fuel pump with Precision Raceworks' Low-Pressure Bucketed Fuel Pump Kits. Precision's low-pressure fuel pumps are designed to flow significantly more fuel than your BMW's stock system, ideal for customers who are upgrading their vehicles or plan to run blended fuel or E85 alone! This is a true plug-and-play solution that anyone can install in their home garage and start taking advantage of the benefits right away. Precision Raceworks' Stage 2+ bucketed fuel pump kit includes a genuine Walbro 535 (F90000295) fuel pump, capable of supporting up to 650whp on 93 octane pump gas or 550whp on 100% E85! In order to prevent having to send in your fuel pump, each of Precision Raceworks' kits includes thorough instructions and all of the items required to assemble your kit at home. This prevents delays in shipping, potential damage to your stock fuel pump housing, and reduces assembly costs to keep prices low. It also improves installation as there is no guesswork on engagement and sealing of o-ring or complications and risks of tightening clamps that can poke holes in critical plastic components nearby. While all bucketless fuel pumps flow .2gpm more than a bucket design that retains the venturi, it comes at a cost. Bucketless pumps should not be driven on tanks lower than 1/4 full and should not be used for road course racing. This is not a disadvantage of only bucketless designs, but also a disadvantage for any bucket design which deletes the venturi. If you do not plan on road course or drag racing (not street racing) and are responsible at maintaining 1/4 tank of fuel during spirited driving, bucketless pumps can be a cheaper alternative for you.

Show More Show Less

Precision Raceworks Replacement Ignition Coil - Blue

T#:4333508

Part#: 201-0091

In Stock

$ 39.99 USD

Add to Wish List

Qty

$ 39.99 USD

Add to Wish List

Replaces individual coils found in the Precision Raceworks Ignition Kit.

VTT N54 Crank Bolt Capture - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557938

Part#: VTT-N54-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice.

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

1x Aluminum Crank Bolt Capture
8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54

Show More Show Less

Vargas N54/55 Billet Crank Seal Guard - BMW N54 N55 3.0L

2X Entries Into Our F80 M3 Sweepstakes

T#:638889

Part#: VTT-CRANKGUARD

In Stock

Starting at $ 89.99 USD

Add to Wish List

Starting at $ 89.99 USD

Add to Wish List

It is a well-known issue on the BMW N54/55 platforms that your serpentine belt can fail for various reasons. When this happens, there is a high chance of the belt getting sucked behind the front damper pulley and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure. Even if you do not lose the engine, it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT, even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Vargas' seal is different from those already on market in two major ways. Firstly, it is not offensively priced. Secondly, it is 100% billet with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long-term corrosion resistance. Crank Seal Guard includes: One VTT Billet N54/55 Crank Seal Guard Two extended 12.9 Grade bolts, and two stainless washers We highly recommend you install WITH a crank bolt capture at the same time, as you have to remove the damper anyway. Then you will get the benefit of helping eliminate the dreaded spun crank hub and the crank seal issue

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

2X Entries Into Our F80 M3 Sweepstakes

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Replacement Fuel Filter Element - 6 Micron | Precision Raceworks ...

T#:38161701

Part#: 101-0257

In Stock

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Replacement Fuel Filter Element - 6 Micron | Precision Raceworks is designed for BMW and high-performance fuel systems, ensuring optimal fuel flow and superior filtration. This high-efficiency 6-micron filter element effectively captures contaminants, preventing debris from reaching fuel injectors and maintaining peak engine performance.

Regular maintenance of your fuel filter is essential for maximizing fuel system efficiency. Whether for racing or daily driving, this replacement element keeps your fuel system running at its best.

6-micron filtration – Removes fine particles and contaminants to protect engine components
High-performance compatibility – Designed for use with Precision Raceworks inline fuel filters
Optimized fuel flow – Maintains consistent fuel delivery for peak performance
Durable construction – Engineered for long-lasting reliability in high-demand applications
Easy replacement – Simple installation for routine maintenance
Ideal for both street and track use – Ensures clean fuel supply for all driving conditions

Fuel Filter Replacement Guidelines:

Racing applications: Inspect at least twice per season and replace as needed
Daily driving: Inspect at least once a year or every 6,000 miles, replacing as necessary

Ensure your BMW fuel system stays clean and efficient with the Replacement Fuel Filter Element - 6 Micron | Precision Raceworks, the ultimate choice for maintaining performance and reliability.

Show More Show Less

E82 135i N54, E9X 335 N54, E60 535 Vargas Upgraded PCV Valve ...

2X Entries Into Our F80 M3 Sweepstakes

T#:389684

Part#: VTT-N54-PCV

In Stock

$ 68.99 USD

Add to Wish List

Qty

$ 68.99 USD

Add to Wish List

The crankcase oil vent system on the N52/N54 is one of its weakest and cheaply designed systems. We see crankcase vent issues on even stock engines but with more boost the problems are exponential. This Vargas upgraded PCV valve, and an oil catch can, are what the N54 engine needs and may alleviate most of your oil and boost leak issues. The PCV valve is supposed to let oil either return to the oil pan or pass through the intake manifold and get burned up in the combustion chamber. However, BMW used a weak plastic vent valve that doesn't seal well when under boost. Instead of closing and venting the oil out of the intake, it's forced through this valve and into the intake and coating your valves with oil residue and carbon. Most boost equals more oil forcing its way by. This upgraded N54 PCV valve uses higher grade materials, including aluminum, to provide a better seal and prevent oil from entering the intake. It's an easy install and a must-have item when considering any turbo work.

Show More Show Less

Port Injection Fuel Line For Top Mount Fuel Rail - N54 N55

T#:38094311

Part#: 201-0188

In Stock

$ 54.99 USD

Add to Wish List

Qty

$ 54.99 USD

Add to Wish List

Port Injection Fuel Line For Top Mount Fuel Rail - N54 N55 is designed for seamless compatibility with most aftermarket intake manifolds featuring top mount port injection. It works with leading brands such as Black Market Parts, BKC, BMS, Sharp Custom, Doc Race, and more, ensuring a high-performance fuel delivery solution for BMW N54 and N55 engines.

Constructed with premium 6061 aluminum and anodized for 100% E85 compliance, this fuel line is engineered for durability and optimal fuel flow. The female quick connectors feature an air hose-style quick connect with dual seals (primary and secondary) to eliminate any risk of fuel leaks. Precision Raceworks utilizes Smooth Bore PTFE hose, a trusted component in high-end E85 applications worldwide.

This plug-and-play solution is fully compatible with both factory and aftermarket fuel lines, providing an easy, reliable way to supply fuel to the port injection system of your upgraded intake manifold.

Seamless fit – Compatible with most aftermarket top mount port injection manifolds
Durable construction – Machined from 6061 aluminum and anodized for E85 compatibility
Leak-proof design – Dual-seal quick connectors for maximum fuel safety
High-performance fuel delivery – Utilizes Smooth Bore PTFE hose for optimal flow
Easy installation – Direct plug-and-play with factory and aftermarket fuel lines

Show More Show Less

Precision Raceworks Ethanol 360 Fittings - 3/8" (9.49mm)

Universal Product - Please confirm your fuel line size prior to ordering

T#:37892104

Part#: 601-0288

In Stock

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

The Precision Raceworks Ethanol 360 fuel line fittings are designed to work in almost any application where you have 3/8" (9.49mm) quick-connect fittings and need to add a flex fuel sensor. These fittings work with almost all ethanol sensors without the need to cut and splice or replace entire line sets. This is a perfect way to add an ethanol sensor to your vehicle while maintaining existing fuel lines.

Show More Show Less

Precision Raceworks Upgraded Fuel Lines W/ Ethanol Sensor Connection ...

T#:10714270

Part#: 201-0247

In Stock

$ 164.99 USD

Add to Wish List

Qty

$ 164.99 USD

Add to Wish List

NOTE: Requires a Continental Flex Fuel Sensor be utilized, will not directly replace the OE fuel line. The Precision Raceworks AN6 Fuel line upgrade is a direct replacement from the fuel filter on the driver’s side of the car to the high-pressure fuel pump. All connections are designed in-house and machined from 6061 aluminum then anodized for 100% E85 compliance. All female connectors have 2 seals (a primary and secondary seal) to guarantee no possible fuel leaks. The fuel line used by Precision Raceworks is smooth bore PTFE hose that is wrapped in a Stainless Steel braiding for protection and then a nylon braiding to protect surfaces. This type of hose is used in high-end E85 applications built all over the world. This is a better than OEM quality solution to help you achieve the needs of your high horsepower build on E85. Specifications: Fuel hose type: PTFE Smooth Bore Line Size: -6AN (1/2") Connection Style: OEM Quick Connect Connector Material: 6061 Aircraft Grade Aluminum Connects to flex fuel sensor: Yes

Show More Show Less

N54 Replacement Spark Plug Wires - 6pk, Blue, Short (Factory Location...

T#:25374610

Part#: 201-0003

In Stock

$ 69.99 USD

Add to Wish List

Qty

$ 69.99 USD

Add to Wish List

Precision Raceworks BMW N54 Factory Location Replacement Spark Plug Wires are the same high-quality wires featured in our acclaimed BMW N54 High-Performance Ignition Kit. Engineered with low-resistance, high-performance technology, these spark plug wires are a fully custom design. Precision Raceworks is the only manufacturer worldwide to create spark plug wires with boots specifically designed for the N54 BMW, ensuring optimal fitment and superior quality.

Show More Show Less

Precision Raceworks Universal Fuel Line NPT Tap - Quick Disconnect Ad...

T#:38161736

Part#: 201-0405

In Stock

$ 24.99 USD

Add to Wish List

Qty

$ 24.99 USD

Add to Wish List

This fitting allows you to install a 1/8" npt port anywhere you have an existing quick connect Compatible with the Motiv 0-10 Bar pressure sensor

Precision Raceworks Replacement Spark Plug Wires - For 601-0021 & 601...

T#:3786918

Part#: 201-0002

In Stock

$ 69.99 USD

Add to Wish List

Qty

$ 69.99 USD

Add to Wish List

Precision Raceworks' BMW N54 / N55 replacement spark plug wires are the same plug wires that are included in their High-Performance Ignition Kits 601-0021 & 601-0021-1

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:18733532

Part#: VTT-CRANKHUB-6

In Stock

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Precision Raceworks N54 N55 High Performance Ignition Kit - OEM Manif...

T#:1271579

Part#: 601-0021

Back Ordered

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

Rid your BMW's N54 of misfires, sluggish throttle response, rough idle, and power loss with Precision Raceworks' High-Performance Ignition Kit! Precision Raceworks' ignition kit is designed to fit any vehicle with an N54 engine and offers the highest output of any kit on the market! Featuring 100% Plug-&-Play connections, low resistance 50ohm/ft proprietary plug wires, and design technology from Marine and Aerospace applications, these coils are guaranteed to output consistent high voltage and current for optimal ignition system performance and reliability. Every component in this kit meets or exceeds OEM quality and features premium seals for dust and water resistance. While coils do not directly increase horsepower, stock BMW coils can wear out quickly, resulting in underperforming voltage and current output. This often leads to weaker spark intensity and reduced power output. Due to the increased voltage and current output, many customers have seen as much as 20+ whp/wtq gained by switching to Precision Raceworks coils over all other coils on the market! By upgrading to Precision's Performance Ignition Kit, spark quality can be restored, and lost power regained often with the additional power beyond what other coils provide. No software tune is required for installation or operation, but if desired, coil output can be increased to 118mJ from most software tuning companies! Features: Fits any N54 BMW engine w/ the stock intake manifold 100% Plug & Play! Highest Voltage and Current Output Available Low Resistance 50ohm/ft proprietary plug wires Eliminates Ignition Related Misfires Improves Throttle Response Restores Smooth Idle Specifications: Weight: 9lbs Full DME control of ignition coils: Yes Retains factory cooled controlled system: Yes 100% Plug and Play wiring: Yes Connection style: OEM Weatherproof Quick Connect Coil output: Up to 118mJ

Show More Show Less

Part#: VTT-N54-PSN54

Ships in 2 Business Days

Starting at $ 56.99 USD

Add to Wish List

Starting at $ 56.99 USD

Add to Wish List

Vargas has introduced their new Billet Power Steering pulleys for the N54 engine! A well-known issue with the N54 with Hydraulic power steering is the plastic pulley either hitting the subframe, or breaking on its own. This can result in the belt to be ejected from the pulley, and leave you stranded with no serpentine belt. This also increases the chance of sucking the belt into the engine through the front seal. Put an end to the dreaded plastic PS pulley issues with the VTT 100% Billet Aluminum PS pulley. These are constructed from 6061-T6 aluminum and anodize in one of 4 colors (Black, Red, Blue, and Clear) for a great look, and long-lasting finish. These weigh 11oz, very close to the weight of a stock pulley, and are lighter than the cast aluminum versions on the market.

Show More Show Less

Vargas Ignition Coil Kit (Blue) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309605

Part#: VTT-COIL-N5X-BLU

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

VTT N54 Billet Vacuum (Boost Control) Tank Kit - Anodized Clear - BMW...

2X Entries Into Our F80 M3 Sweepstakes

T#:7530039

Part#: VACUUMCANRAW

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

VTT is proud to offer their billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and use it to regulate boost via the solenoids. The stock plastic can and small plastic nipples on the stock cans have a tendency to crank over time, and if they leak you will get low boost, or no boost, and poor performance. These cans do away with the weak plastic cans while adding some pop, and color to your engine bay. These vacuum cans retain ALL of the factory provisions including mounting points but come with 90-degree fittings for easier routing of the lines VTT's cans are made of 6061-T6 aluminum, and anodized in 4 colors for beauty, and long life. They also knurl the cans for a very distinct look in the engine bay! VTT also designed these cans to complement their N54 Billet lineup – N5X Billet Oil caps, N5XBillet Oil filter housing caps, Billet coolant cap, Billet valve cover, billet oil cooler block off plate, and Billet Power Steering cap, and so on. All will have matching color These cans are offered in 4 colors – Red, Black, Blue, and Clear anodize The kit will include: 2 – Vacuum canisters (color of choice) 4 – billet 90-degree barbed fittings Requires the additional use of aftermarket vacuum line - Vacuum line not included. Replaces Genuine BMW Vacuum Canisters # 11652247620

Show More Show Less

Precision Raceworks High Performance Fuel Pump Kit - Stage 3 - BMW E-...

T#:5216002

Part#: 601-0110

In Stock

$ 868.99 USD

Add to Wish List

Qty

$ 868.99 USD

Add to Wish List

If you are looking to get more power out of your BMW, it's important not to forget your fueling system! Your low and high-pressure fuel pumps can only flow so much fuel, limiting power potential regardless of turbo size or other power adders, especially true when running ethanol blends. Bring your fuel system up to par with Precision Raceworks' E-Chassis High-Performance Fuel Pump Kits! Precision's low-pressure fuel pumps are designed to flow significantly more fuel than your BMW's stock system, ideal for customers who are upgrading their vehicles or plan to run blended fuel or E85 alone. Best of all, these pumps ship completely assembled and ready to install! New pump, new fuel filter, and new sending unit included! This is a true plug-and-play solution that anyone can install in their home garage and start taking advantage of the benefits right away. By design, a fuel pump such as this is ideal for daily driving and racing applications of all kinds. This system keeps the primary pump fully submerged in fuel regardless of tank level or the g-force the car is subjected to. Precision Raceworks' Stage 3 bucketed fuel pump kit includes a Walbro 450 (F90000274) fuel pump, capable of supporting up to 1000whp on 93 octane pump gas or 875whp on 100% E85! Even better yet? No wires to cut or splice, nothing to assemble, 100% OEM quality, and drop-in ready. Included in the box New genuine OEM fuel pump bucket assembly (Pre-assembled with genuine Walbro 450 pump) Includes new fuel sending unit (fuel level sensor) New primary and secondary fuel filters Stage 3 Specifications: Horsepower Supported Pump Gas: ~1000whp Horsepower Supported 100% E85: ~875whp Aftermarket EKP Required: No **Some European Spec vehicles may require the re-use of the top hat due to differences in emissions requirements.

Show More Show Less

VTT Billet BMW Crankcase Breather - Screw In - BMW N54 N55 3.0L ...

2X Entries Into Our F80 M3 Sweepstakes
FOR MODELS WITH VTT BILLET VALVE COVER ONLY

T#:38924625

Part#: VTT-CRANKBREATHE

In Stock

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

VTT is happy to introduce the first and only available plug and play ONE-WAY crankcase breather kit for BMW B58 applications. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay. FITS with the engine cover on. Engine cover can be removed, and installed without removing the breather. This breather can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups, including most aftermarket oil catch can systems! The breather sits about 2.5' tall from the valve cover oil cap area, and the filter is 2-3/4' in diameter Is your car a Gen1 or TU? Pull your oil cap off, and check how it attaches. 2 Prong style is Gen-1, snap-in style with grooves is TU.

Show More Show Less

VTT Ignition Coil Conversion Kit - S55/N55 To B58 - Multiple Color Op...

2X Entries Into Our F80 M3 Sweepstakes

T#:22196341

Part#: VTTS55CLCNV

Ships in 8 Business Days

Starting at $ 335.99 USD

Add to Wish List

Starting at $ 335.99 USD

Add to Wish List

VTT is proud to offer its very own Game Changer S55/N55 to B58 Coil conversion kit for the BMW S55/N55 platforms. The 55 series of engines has notoriously had ignition problems with the factory coils, while aftermarket upgrades do exist, they can be bulky. The solution is the BMW B58 ignition coils which are extremely robust and can support well over 1000WHP with no issues. This means a plug-and-play affordable solution that fits like stock, and looks AMAZING doing so! We designed our own 6061-T6 Billet bracket in a plethora of colors including matching shades for every S55/N55 Valve Cover. This means you can mix and match the color of the bracket with coil color, with VC color to truly tailor your engine bay to look exactly how you want it to! The kit comes with the following: 3 – Billet Aluminum Coil Brackets in the color of choice 6 – Plug and play VTT wiring harnesses 6 – Custom VTT stalks to convert the B58 coils to the S55/N55 head (We ensure proper spring length inside the boot for optimal spring-to-plug contact) *NOTE: Flash setting changes may be required when installing the conversion kit to ensure the proper function of the B58 coils with S55/N55 DME. This can be found in almost all flashing software settings such as MHD, Bm3, etc.* **NOTE: THESE BRACKETS FIT STOCK S55 VC, VTT S55 BILLET VC, and MOST N55 made after 2011. If you have an older N55 made before 01/2011. These may not fit. Purchase carefully as items that have been installed or attempted to cannot be returned.**

Show More Show Less

VTT N54 Vacuum Pump Block Off Plate

2X Entries Into Our F80 M3 Sweepstakes

T#:11497328

Part#: VTT-N54-VACUUM-B

Ships in 10 Business Days

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

Looking to remove the HPFP or DI system on your N54? this plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes Block Plate Note – Plates may come in a clear or anodize black finish depending on stock on hand

Show More Show Less

Precision Raceworks Universal Adjustable Fuel Pressure Regulator W/ 1...

T#:38195449

Part#: 501-0043

In Stock

$ 159.99 USD

Add to Wish List

Qty

$ 159.99 USD

Add to Wish List

Adjust your fuel pressure as needed. Thanks to the 1:1 boost reference, fuel pressure will increase as boost pressure increases, ensuring fuel delivery remains optimal under all conditions.

BMW N55 Turbocharger install kit

2X Entries Into Our F80 M3 Sweepstakes

T#:398463

Part#: VTT-N55-INSTL

Ships in 1 Business Day

$ 222.99 USD

Add to Wish List

Qty

$ 222.99 USD

Add to Wish List

Vargas Turbo has done it again. They've made it even easier for you to get your car back on the road and running right again with your new turbos. They've put together an install kit containing all the components you need to get your new turbos installed properly and efficiently. This means you can get your car back on the road faster and enjoy your new turbos!

Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.

Show More Show Less

T#:38161752

Part#: 201-0148

Ships in 6 Business Days

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Precision Raceworks' Port Injection Fuel Line is designed to be compatible with most plate-style port injection kits on the market. Crafted from high-quality 6061 aluminum, all connections are precisely machined and fully compatible with E85 fuel. The female connectors feature dual seals, ensuring a leak-free performance. The fuel line itself is constructed from smooth-bore PTFE hose, a proven choice for numerous E85 applications. This plug-and-play solution seamlessly integrates with both factory and aftermarket fuel rails, offering a hassle-free way to deliver fuel to your port injection system.

Show More Show Less

Billet Check Valve - 10 Barb

2X Entries Into Our F80 M3 Sweepstakes

T#:597641

Part#: VTT-CHECK-2

Ships in 2 Business Days

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

PNP Ethanol Sensor Harness For Motiv Re|Flex Plus

T#:38161679

Part#: 201-0410

Ships in 8 Business Days

$ 49.00 USD

Add to Wish List

Qty

$ 49.00 USD

Add to Wish List

Ideal for enthusiasts looking to optimize their vehicle’s fuel system, this ethanol sensor harness delivers precision and reliability for high-performance applications.

BMW N54 3.0L Wastegate Rattle Fix Repair Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:398014

Part#: VTT-N54-WF2

Ships on Sep 21, 2026

$ 95.99 USD

Add to Wish List

Qty

$ 95.99 USD

Add to Wish List

VTT N54 Waste Gate Repair Kit / Rattle Fix Tired of the annoying N54 Wastegate Rattle? Turbos still going strong, but can't deal with the embarrassing rattle anymore? We have the perfect kit for you. This kit comes with 1 set (both turbos) of Stainless Steel wear matched bushing, and flapper assembly, Wastegate arm, rod end, and Stainless steel 8mm C clip. These parts custom made for VTT upgrade the flapper assembly to a full 12.6MM or 1/2" flapper arm, and bushing compared to the stock 11.5mm. They also get rid of the 6mm rod end connection to a full 8mm connection with a stainless steel C clip. There is no better N54 Waste Gate upgrade on the market, and guess what? We also offer them for less than other upgrades which use the stock bushing size, rod end, and inferior materials. If you want to fix this right the first time, this is the kit for you! *Please note, assembly is required. This kit can only be installed with the turbos removed from the vehicle, and stock wastegate assembly removed from the housing. The new assemblies will need to be pressed in, then welded by a qualified welder. We offer no warranty, or returns for improperly installed wastegate assemblies.

Show More Show Less

Precision Raceworks Bucketed High Performance Fuel Pump Kit - Stage 2...

T#:8169508

Part#: 601-0116

In Stock

$ 594.99 USD

Add to Wish List

Qty

$ 594.99 USD

Add to Wish List

The Precision Raceworks E9x / E8x LOW PRESSURE BUCKETED FUEL PUMPS are designed for customers looking to run all blends of E85 and flow up to 3.9 liters per minute. The included Genuine Walbro 535 (F90000295) fuel pump is capable of flowing up to 350% more fuel than the factory fuel pump and is 100% E85 compliant. Precision Raceworks' Stage 2.5 V2 bucketed fuel pump comes with a single Walbro 535 (F90000295) fuel pump. This pump can support up to 650whp (Rated for 550whp on 100% E85) and is ready to grow with you as your needs demand. Unlike other manufacturers, Precision Raceworks is the only company featuring a bucketed kit with a modular design. This means you can purchase their stage 3 pump module or Stage 3.5 module and upgrade the pump as your needs change. If you are looking for a 100% assembled drop-in-ready solution, this is the choice for you! **Some European Spec vehicles may require the re-use of the top hat due to differences in emissions requirements. This is a true plug-and-play solution that anyone can install in their home garage and start taking advantage of the benefits right away. Features & Specifications: Lock Ring Tool Included Pump flow 72psi (5bar): 1.0 GPM / 3.9 LPM Pump Weight: 3.98 lbs Horsepower Supported Pump Gas: 650 Horsepower Supported 100% E85: 550 Aftermarket EKP Required: No

Show More Show Less

BMW Secondary Pump Activation Harness - BMW E9X F22/23 F3X F8X ...

T#:38094337

Part#: 201-0049

In Stock

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

Precision Raceworks' BMW Secondary Pump Activation Harness is the top choice among pump manufacturers and tuners for controlling auxiliary fuel pumps. This kit is considered the most complete and highest quality kit on the market and is sold private label to many BMW pump manufacturers. That is why this harness is the #1 method of secondary pump control on the market around the globe.

Show More Show Less

Precision Raceworks High Performance Ignition Kit - Blue Coils - BMW ...

T#:26205125

Part#: 601-0149-1

Ships in 8 Business Days

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

Rid your BMW's N55 of misfires, sluggish throttle response, rough idle, and power loss with Precision Raceworks' High-Performance Ignition Kit! Precision Raceworks' ignition kit is designed to fit any vehicle with an N55 engine and offers the highest output of any kit on the market! Featuring 100% Plug-&-Play connections, low resistance 50ohm/ft proprietary plug wires, and design technology from Marine and Aerospace applications, these coils are guaranteed to output consistent high voltage and current for optimal ignition system performance and reliability. Every component in this kit meets or exceeds OEM quality and features premium seals for dust and water resistance. While coils do not directly increase horsepower, stock BMW coils can wear out quickly, resulting in underperforming voltage and current output. This often leads to weaker spark intensity and reduced power output. Due to the increased voltage and current output, many customers have seen as much as 20+ whp/wtq gained by switching to Precision Raceworks coils over all other coils on the market! By upgrading to Precision's Performance Ignition Kit, spark quality can be restored, and lost power regained often with the additional power beyond what other coils provide. No software tune is required for installation or operation, but if desired, coil output can be increased to 118mJ from most software tuning companies!

Show More Show Less

BMW N54 3.0L Billet Vaccum Relief Valve

2X Entries Into Our F80 M3 Sweepstakes

T#:597525

Part#: VTT-VAC-RELIEF

Ships in 2 Business Days

$ 104.99 USD

Add to Wish List

Qty

$ 104.99 USD

Add to Wish List

BMW N54 3.0L Billet Vacuum Relief Valve from Vargas Turbo Technologies offers precise control over crankcase vacuum levels. This high-quality billet valve allows users to adjust the vacuum pressure with ease, eliminating guesswork and ensuring optimal engine performance. By simply adding or removing shims, users can tailor the vacuum level to their needs.

Customizable Vacuum Levels: Adjust the vacuum pressure using supplied shims to achieve desired performance.
Direct Fit: Designed with -10ORB threads for easy installation into VTT modular PCV solutions and VTT Modular CNC valve covers.
Versatile Settings: Includes 5 vacuum settings ranging from 10' to 18' of vacuum based on shim configuration.
Enhanced Engine Protection: Helps prevent excessive vacuum that could affect engine seals or cause whistling.

Show More Show Less

Black Market Parts Low-Pressure Bucketless Fuel Pump Kit - Stage 3 - ...

T#:5215998

Part#: 601-0018

In Stock

$ 549.99 USD

Add to Wish List

Qty

$ 549.99 USD

Add to Wish List

When upgrading your turbos or increasing your BMW's power potential, it's important not to overlook your fuel pump. Both low and high-pressure fuel pumps can only flow so much fuel, limiting power potential regardless of turbo size or other power adders, especially when running ethanol blends. If you are looking to get more power out of your BMW, it's important not to forget your fueling system! Your low and high-pressure fuel pumps can only flow so much fuel, limiting power potential regardless of turbo size or other power adders, especially true when running an ethanol blend. Bring your fuel system up to par with the Black Market Parts (By Precision Raceworks) Low-Pressure Bucketless Fuel Pump! Precision's low-pressure fuel pumps are designed to flow significantly more fuel than your BMW's stock system, ideal for customers who are upgrading their vehicles or plan to run blended fuel or E85 alone. This is a true plug-and-play solution that anyone can install in their home garage and start taking advantage of the benefits right away. The Black Market Parts Stage 3 bucketless fuel pump kit includes a genuine Walbro 450 (F90000274) fuel pump, of supporting up to 1050whp on 93 octane pump gas or 875whp on 100% E85, and is the perfect modular pump to get you started! Since Precision Raceworks is always looking ahead, they have designed their modular bucketless fuel pump to allow you to upgrade your fuel pump as needed! With an open expansion slot ready to use, just a simple Stage 3.5 or Stage 4 module is all you need to purchase to increase your fueling capabilities. While all bucketless fuel pumps flow .2gpm more than a bucket design that retains the venturi, it comes at a cost. Bucketless pumps should not be driven on tanks lower than 1/4 full and should not be used for road course or drag racing. This is not a disadvantage of only bucketless designs, but also a disadvantage for any bucket design which deletes the venturi. If you do not plan on road course racing (not street racing) and are responsible at maintaining 1/4 tank of fuel during spirited driving, bucketless pumps can be a cheaper alternative for you. Stage 2 Specifications: Horsepower Supported Pump Gas: ~1050whp Horsepower Supported 100% E85: ~875whp Aftermarket EKP Required: No *To reach the advertised ability of these fuel pumps use of the Precision Raceworks in-tank filter regulator assembly is required.

Show More Show Less

BMW N54 Replacement Coil Power Harness - Set Of 6 - Manifold Location...

T#:24112786

Part#: 201-0008-1

In Stock

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Flapper Delete Fitting - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:557962

Part#: VTT-FLAPPER-DELE

Ships in 10 Business Days

$ 57.99 USD

Add to Wish List

Qty

$ 57.99 USD

Add to Wish List

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

The VTT PCV Flapper delete is used to get rid of the factory flapper, and add a -10 fitting on N54 powered vehicles. This will allow you to run a single or dual external catch can, or your own custom set up.

This fitting is made from 6061-T6 aircraft aluminum anodized black and comes with O-ring, and a stainless steel holding clip.

This part fits the following BMW engines:
2006-2012 N54

Show More Show Less

VTT N54 Billet Vacuum (Boost Control) Tank Kit - Anodized Red - BMW E...

2X Entries Into Our F80 M3 Sweepstakes

T#:7530038

Part#: VACUUMCANRED

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

VTT is proud to offer their billet replacement for the factory plastic vacuum tanks that store vacuum from the pump and use it to regulate boost via the solenoids. The stock plastic can and small plastic nipples on the stock cans have a tendency to crank over time, and if they leak you will get low boost, or no boost, and poor performance. These cans do away with the weak plastic cans while adding some pop, and color to your engine bay. These vacuum cans retain ALL of the factory provisions including mounting points but come with 90-degree fittings for easier routing of the lines VTT's cans are made of 6061-T6 aluminum, and anodized in 4 colors for beauty, and long life. They also knurl the cans for a very distinct look in the engine bay! VTT also designed these cans to complement their N54 Billet lineup – N5X Billet Oil caps, N5XBillet Oil filter housing caps, Billet coolant cap, Billet valve cover, billet oil cooler block off plate, and Billet Power Steering cap, and so on. All will have matching color These cans are offered in 4 colors – Red, Black, Blue, and Clear anodize The kit will include: 2 – Vacuum canisters (color of choice) 4 – billet 90-degree barbed fittings Requires the additional use of aftermarket vacuum line - Vacuum line not included. Replaces Genuine BMW Vacuum Canisters # 11652247620

Show More Show Less