BMW Engine Parts for BMW 1 Series E82 (2008-2013)

Continental is the OEM supplier for the stock serpentine accessory belt on your N52 engine.?Over time, accessory belts begin?to wear out and crack. This can lead to the belt slipping, squeaking, or even snapping. Replace your belt on a regular basis to ensure you don't end up stranded on the side of the road with a dead battery or over heated engine due to a bit of simple overlooked maintenance.

Fits the following BMW chassis:
E90 E82/8 E60 E70 E83 E63/64

This sensor monitors the position of the Valvetronic eccentric shaft and feeds data back to the ECU. The common issue with this sensor is that it gets contaminated with oil and fails. It doesn't give a fault code or check engine light, however. What you would notice is sluggish driving, hesitation, poor performance, jerky shifts from an automatic, and other drivability issues. These types of issues are typically diagnosed as ignition coils (which are their own issue altogether) but this sensor may also be faulty.

The eccentric shaft sensor is located at the front of the cylinder head and is only accessible with the valve cover off. It's easy to check for oil by removing the engine trim cover (the outer cover with the BMW roundel), unplug the sensor, and look inside. If oil is present inside, or even on the valve cover itself, the sensor is likely contaminated or ready to fail. You can wipe or clean the oil from sitting inside the sensor but it will come back.

If you're planning this job make sure you have our Valve Cover Overhaul Kit, which includes a new seal for the eccentric sensor as well as the rest of the valve cover and Valvetronic gaskets. You can add the valve cover set from the options below.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008+ E82 BMW 128i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2006-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive
2010+ F07 BMW 535i GT, 535i xDrive GT, 550i GT, 550i xDrive GT
2011 F10 BMW 528i
2006-2010 E83 BMW X3 3.0i X3 3.0si
2011 F25 BMW X3 xDrive28i
2007-2010 E70 BMW X5 3.0si X5 xDrive30i
2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive30i

This is the OEM VDO fuel pump and fuel level sensor for most E82 and E9X cars. If your gas gauge is not reading correctly, or not at all, it's probably the level sensor on this pump. Unfortunately, the level sensor is part of the pump assembly and must be replaced as a whole. This fuel pump fits nearly all E82, E90, E92, and E93 turbo and non-turbo cars.

OEM replacement for BMW part # 16147163298.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Vargas Turbo has done it again. They've made it even easier for you to get your car back on the road and running right again with your new turbos. They've put together an install kit containing all the components you need to get your new turbos installed properly and efficiently. This means you can get your car back on the road faster and enjoy your new turbos! 

Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.

BMW N54 3.0L Billet Vacuum Relief Valve from Vargas Turbo Technologies offers precise control over crankcase vacuum levels. This high-quality billet valve allows users to adjust the vacuum pressure with ease, eliminating guesswork and ensuring optimal engine performance. By simply adding or removing shims, users can tailor the vacuum level to their needs.

• Customizable Vacuum Levels: Adjust the vacuum pressure using supplied shims to achieve desired performance.
• Direct Fit: Designed with -10ORB threads for easy installation into VTT modular PCV solutions and VTT Modular CNC valve covers.
• Versatile Settings: Includes 5 vacuum settings ranging from 10' to 18' of vacuum based on shim configuration.
• Enhanced Engine Protection: Helps prevent excessive vacuum that could affect engine seals or cause whistling.