BMW Intake Parts for BMW 1 Series E82 (2008-2013)

Replacement N55 Performance Filter from Burger Motorsport

Enhance your BMW's performance with the Replacement N55 Performance Filter from Burger Motorsport. Specifically designed for N55 engines, this filter optimizes airflow, leading to increased horsepower and torque. Enjoy improved throttle response and fuel efficiency, all while protecting your engine from harmful contaminants.

Key Features:

• Designed for N55 engines
• Optimizes airflow for increased power
• Improves throttle response and fuel efficiency
• Protects engine from contaminants

An easy way to improve the performance of your N54 powered BMW is by removing the stock air box and swapping in this Dual Cone Intake "DCI" from Burger Motorsports. Featuring two S&B inverted cone filters with adapter couplers and new hardware, these easily install into the stock box location, allowing for greatly improved intake air flow. This is great for both stock and modified vehicles, as this allows for greater air flow at all RPMs and removes the air restriction that would normally rob your engine of power.

In addition to increased power, these filters give your engine a more aggressive appearance and sound that any automotive enthusiast will appreciate.

MADE IN THE USA

**CARB Approved Under Executive Order (EO) No. D-744-2 for all 2007-2012 BMW models equipped with the N54 3.0L twin-turbocharged 6-cylinder engine.**

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

This is a 1/2" (fits -8AN hos perfectly as well) CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run the vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.

This part fits the following BMW engines:
2006-2012 N54

Looking to upgrade your intercooler? This Phoenix Racing intercooler designed by Burger Motorsport is a great option that delivers better cooling, more power to the wheels, and allows you to hold that power longer during extended runs. A larger core and increased surface area dramatically improves cooling and reduces pressure drop. After extensive testing, this can allow your N54/55 powered BMW to gain around 10+peak wheel horsepower and during longer pulls and multiple runs, as much as 20-30whp over the factory intercooler.

Phoenix replacement intercoolers are a direct replacement for your factory intercooler and fully reversible. All required hardware is included. 

Dimensions: 20" x 5.25" x 5.25"

If you are looking to replace your stock chargepipe for better reliability and higher performance, the Burger Motorsports designed and Phoenix Racing built Performance Aluminum Chargepipe is an excellent choice! This aluminum chargepipe is significantly stronger than the stock plastic pipe and the powder coated aluminum looks great and will resist any corrosion. Plus, this chargepipe features a 3 inch design for optimal flow at all RPMs, prevent restriction that would normally be seen with the stock pipe. This is perfect for someone looking to upgrade a stock or tuned N54!

Specs and Features:

• Aluminum Construction
• Black Powder Coating
• 3" Diameter
• CNC Machined Throttle Body Flange
• Dual 1/8" NPT Bungs
• High Pressure T-Bolt Clamps
• All Required Installation Hardware

O-rings and retaining clip must be reused from the original pipe or purchased new for proper installation.

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

This is the adapter fitting that is required to convert your N54 to external PCV if you want to keep your crankcase under vacuum at idle, and anytime you have a vacuum condition in your intake manifold. They are made from 6061-T6 with black anodizing for a long-lasting finish. Includes complete adapter, with all o-rings, and retaining clip.

This must be used in conjunction with  the Vargas billet check valve, and PCV delete fitting or requires plugging of the intake PCV ports. Installs inline on the throttle body, and adds a -8AN male to adapt to a catch cans, or any custom set up.

Made from 6061-T6 with black anodizing for a long-lasting finish. Includes complete adapter, with all o-rings, and retaining clip

This part fits the following BMW engines: 
2006-2012 N54