BMW Engine Parts for BMW X Series E84 (2013-2015)

Introducing our Turner Motorsport Crank Seal Guard – the essential shield for your BMW's engine integrity. Safeguarding the heart of your vehicle, this meticulously designed guard offers robust protection for the crank seal concealed behind the harmonic balancer.

Considered an indispensable maintenance component for your BMW, the Crank Seal Guard acts as a crucial defense against a potential and preventable catastrophe involving your accessory belt. Facing the reality of potential oil or coolant leaks in your engine, this guard becomes a reliable barrier, preventing these fluids from reaching the accessory belt. The consequence of a compromised belt includes walking, slipping, fraying, and rubber particles finding their way behind the harmonic balancer and into the crank seal – a scenario that can lead to severe engine failure.

Let's be honest, engine leaks are a common occurrence, and whether your engine is currently leaking or not, the Crank Seal Guard is a proactive measure against future threats. The wear and tear on the accessory belt due to oil and coolant exposure can result in slipping, tearing, or, worst-case scenario, belt snapping – posing a significant risk to your engine's well-being.

Prepare your car for the long haul and protect the vital components, It's not a matter of "if" but "when" your belt will become a problem, and our Crank Seal Guard is your proactive solution. Rigorously tested on N52/N54/N55 and S55 for 100% confirmed fitment, it stands as a reliable guardian for your engine's health. Invest in the protection your BMW deserves with the Turner Motorsport Crank Seal Guard.

Key benefits:

Protect crank seal from rogue accessory belts and their shredded debris
Optimized to fit N52, N54, N55, and S55 engines
Rigid design that fits within the space constraints between the engine block and harmonic balancer
Zinc-coated fasteners for corrosion and oxidation resistance
Design:

Modeled and designed from FARO laser scanning and Solidworks CAD
Manufactured from 6061 billet aluminum
Turner blue anodizing
Installation:

It is a good idea to note how your belt is routed before starting the installation.

2 securing bolts for crank seal guard - Torque value of 20Nm

You will find either 6 or 8 E10 bolts are holding the harmonic balancer depending on the engine.

E10 (P#11237564511) ​
​N52: 6 bolts - Torque value of 25nm
N54: 6 bolts - Torque value of 35nm
N55: 8 bolts - Torque value of 35nm

E10 (P#11237575488)
S55: 8 Bolts - Torque value of 35nm

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain system comes complete with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole - drain kit included!
• Universal mounting kit

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain hole can be used with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole (valve and hose sold separately, watch for our model specific drain kits!)

Featuring a T60 Torx head, the belt tensioner found on the N54/N55 engine has exceptionally tight quarters. Use of this tool will allow access to the lock pin hole without excessive component removal, making belt removal and installation a much easier task.

This tool fits all N54/N55 powered BMW, including: 
2008+ E82 BMW 135i 1M Coupe 
2014+ F22 BMW M235i 
2006+ E90 BMW 335i 335xi 335i xDrive - Sedan 
2007+ E92 BMW 335i 335is 335xi 335i xDrive - Coupe 
2007+ E93 BMW 335i - Convertible 
2012+ F30 BMW 335i 335i xDrive - Sedan 
2013+ F32 BMW 435i 435i xDrive - Coupe 
2014+ F34 BMW 335i xDrive GT - Gran Tourismo 
2015+ F80 BMW M3 - Sedan 
2015+ F82 BMW M4 - Coupe 
2015+ F83 BMW M4 - Convertible 
2006-2010 E60 BMW 535i 535xi 535i xDrive 
2010+ F07 BMW 535i GT, 535i xDrive GT 
2011+ F10 BMW 535i 535i xDrive 
2012+ F13 BMW 640i 
2009+ F01 BMW 740i 740li 
2011+ F25 BMW X3 xDrive35i 
2007-2013 E70 BMW X5 xDrive35i 
2007-2014 E71 BMW X6 xDrive35i 
2009+ Z4 BMW Z4 sDrive35i Z4 sDrive35is 

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

BMS Billet Spark Plug Gapper Tool - 14mm is an essential tool for achieving accurate and consistent spark plug gapping, ideal for automotive enthusiasts and professional mechanics alike. This precision tool helps maintain optimal plug performance by providing reliable, consistent gaps. Available in both 14mm and 12mm plug thread sizes, this tool is proudly made in the USA to deliver durability and precision.

• Precisely gaps spark plugs for enhanced engine performance and efficiency
• Speeds up the gapping process while ensuring accuracy and uniformity
• Available in two sizes (14mm and 12mm) for a wider range of compatibility
• Optional specialty feeler gauge included with 4 blades in thicknesses of .018, .020, .022, and .024
• Made in the USA for premium quality and durability

Meet modern emission regulations while preserving engine performance with the ECS Baffled Oil Catch Can. Designed for BMW and MINI vehicles, this system efficiently captures blow-by gases, preventing excessive oil vapor ingestion into the intake tract. The innovative 4-chamber baffle system maximizes oil/air separation, reducing carbon build-up and pollutants. Featuring a 1/4" drain fitting for easy maintenance, this catch can minimizes oil deposits, ensuring cleaner emissions and enhanced engine performance.

Key Benefits:

• Efficient 4-chamber baffle system for maximum oil/air separation
• Recirculated design reduces oil ingestion, promoting cleaner emissions
• Durable 6061-T6 billet machined body with anodized black finish for longevity
• Integrated dipstick and sealed reservoir for easy oil inspection and maintenance
• Serviceable design with removable baffle plates for cleaning
• Easy installation with customizable mounting options and leak-free fittings
• Engineered and manufactured in the USA for superior performance and durability

Note: Not for sale or use in the state of California on any pollution-controlled vehicle as per the California Air Resources Board.

Modern emission regulations require a closed PCV/Breather system for cleaner operation. However, inefficient oil particle capture can lead to excessive oil vapor ingestion, causing carbon buildup, reduced performance, and fuel economy. ECS Tuning's updated ECS Baffled Oil Catch Can, now with an easy-to-empty 1/4" drain fitting, is engineered to collect toxic blow-by gases, minimize carbon deposits, and reduce oil contamination within engine oil. Recirculating oil vapor ensures emissions compliance without venting to the atmosphere.

• Key Features:
• Highly Efficient Oil Separator: Strategically positioned 4 chamber baffle system maximizes oil/air separation and minimizes oil droplets in the intake tract.
• Integrated Dipstick: Knurled and black anodized oil dipstick simplifies oil volume inspection.
• Reservoir: Available in 6oz or 8oz capacity with a 1/4" NPT drain plug fitting.
• Serviceable: Easily removable baffle plates and drain plug for cleaning.
• Easy/Customizable Installation: Combine with the ECS Universal Bracket Kit for simplified installation and adjustable mounting locations.
• Leak-Free Fittings: Machined -10AN ORB (O-Ring Boss) fittings available for secure connections (fittings sold separately).

Schwaben's Self-Adjusting Wire Strippers are an essential addition to any garage or toolbox. Engineered with precision and versatility, these wire strippers automatically adapt to various wire sizes, making them perfect for a wide range of automotive and electrical applications.

Crafted with Schwaben's renowned quality standards, this tool ensures reliable performance and long-lasting durability, helping you tackle wiring tasks efficiently and accurately. Whether you're a professional mechanic or a DIY enthusiast, these wire strippers are your go-to solution for seamless and precise wiring repairs.

Key Features:

Ergonomic Design: 6-inch handles with rubber grips provide superior comfort and control during use. Self-Adjusting Stripper Jaws: Serrated jaws offer a secure grip for consistent and accurate stripping. Adjustable Depth Gauge: Enables precise, repeatable wire stripping to match your project’s needs. Wide Range Compatibility: Strips wires ranging from 10 to 24 AWG with ease. Integrated Wire Cutter: Effortlessly slices wires between 10 and 24 AWG. Built-In Crimper: Crimps both insulated and non-insulated wires in sizes from 10 to 22 AWG. Schwaben’s Self-Adjusting Wire Strippers combine precision, convenience, and durability into one must-have tool, ensuring professional results for every project.

The Schwaben Extended Reach Spark Plug Socket is the perfect tool for removing 5/8-inch spark plugs with deeply recessed plugs.

The five inch long, rigid socket body provides solid engagement with the plug hex to prevent plug breakage.

Features:

• Magnetic ring holds the spark plug but won't stick to the plug porcelain neck like sockets with cheap rubber inserts
• Chrome plated with durable and attractive polished surface
• Turn it with a 3/8-inch ratchet or a 19 mm (¾-inch) socket or box wrench at the external hex head
• Outer diameter of socket is approximately 22mm

Schwaben Professional Mechanic's Work Gloves provide exceptional hand protection with a perfect balance of durability and comfort.

Designed for precision, these gloves offer high dexterity, making it easy to handle even the smallest parts. The tailored elastic cuff with a hook-and-loop closure ensures a secure and comfortable fit.

The textured latex coating on the palm and fingertips delivers superior grip and tactile feedback, while the breathable spandex backing and knit top allow for all-day comfort.

The durable synthetic leather palm enhances longevity, and the unique graphic design reflects the drifting culture of Euro car enthusiasts.

Note: See manufacturers information tab for sizing chart.

Key Features:

• High Dexterity: Perfect for picking up small parts with ease.
• Secure Fit: Tailored elastic cuff with a hook-and-loop closure.
• Enhanced Grip: Textured latex coating on palm and fingertips.
• All-Day Comfort: Breathable spandex backing and knit top.
• Durable Design: Synthetic leather palm for extended wear.
• Unique Style: Graphic design inspired by the drifting culture of Euro owners.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Perfect for any job when it comes to keeping your hands clean and protected.

Features:

• High dexterity
• Elastic hook and loop strap
• Textured latex finger tips for grip
• Breathable material