BMW Engine Parts for BMW X Series E84 (2013-2015)

OEM Rein Oil Pan Bolt Set - M54 N52 N54 N55

2X Entries Into Our F80 M3 Sweepstakes

T#:379282

Part#: 11132210959

In Stock

Sale - Save 5% $ 44.89

This product was last offered at the strikethrough price on
08-31-2026

$ 42.65 USD

Add to Wish List

Qty

Sale - Save 5%

$ 44.89

This product was last offered at the strikethrough price on
08-31-2026

$ 42.65 USD

Add to Wish List

This is a replacement set of bolts for the oil pan on your BMW equipped with an M54, N52, N54, or N55. The stock bolts are easy to strip, break, or even lose. Replace your missing or damaged bolts with all new hardware from OEM Rein to ensure a tight seal all around your oil pan and prevent oil leaks.

Check fitment with our guide above to ensure these are the oil pan bolts required for your vehicle.

Show More Show Less

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

2X Entries Into Our F80 M3 Sweepstakes

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Bav Auto Spark Plug Socket 12" x 5/8"

10X Entries Into Our F80 M3 Sweepstakes

T#:580385

Part#: B8800072

In Stock

Sale - Save 25% $ 37.99

This product was last offered at the strikethrough price on
05-03-2026

$ 28.49 USD

Add to Wish List

Qty

Sale - Save 25%

$ 37.99

This product was last offered at the strikethrough price on
05-03-2026

$ 28.49 USD

Add to Wish List

Magnetic insert holds the spark plug securely in place for easy installation. Works great on many twin can engines where the spark plugs are recessed deep in the cylinder head.

Billet Oil Filter Cap

T#:21045489

Part#: BMS-OFC

In Stock

Starting at $ 89.00 USD

Add to Wish List

Starting at $ 89.00 USD

Add to Wish List

The Burger Motorsports V2 billet aluminum oil filter cover is a metal upgrade that directly replaces your weak OE plastic cap for greater protection, better cooling, ease of removal/install, and looks great under the hood. The built-in 21mm hex and a 3/8" drive socket wrench fitting that does not require a special removal/install tool like the factory cap. Uses the OE oil filter, filter housing o-ring, and filter cage. Anodized for protection. This quality part is a must for any serious BMW owner. Replaces OEM part number 11427525334 - BMW Oil filter cover. Features and Benefits Solid aluminum design is much stronger than brittle plastic 21mm hex head + 3/8" drive socket wrench fitting Integrated heat sinks for better oil cooling Special tools are not required for removal/install like the factory cap Strong design won't fail under pressure Reuses OE filter cage and o-ring Anodized for protection Looks great under the hood Made in the USA

Show More Show Less

BMW Oil Cap Crankcase Breather - All BMW w/2 prong oil fill cap ...

2X Entries Into Our F80 M3 Sweepstakes

T#:558084

Part#: VTT-CRANK-BREATH

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Show More Show Less

Port Injector Plugs

T#:27171925

Part#: UNI-BMS-PIPLUGS

In Stock

$ 60.00 USD

Add to Wish List

Qty

$ 60.00 USD

Add to Wish List

These dummy injectors fit in place of port injection fuel injectors to block the holes. Allows use to aluminum manifolds with port injection bungs without having to purchase fuel injectors. Plugs are EV14 injectors and measure 38mm or 1.5" from o-ring to o-ring.

Show More Show Less

Burger Motorsport 4 BAR TMAP Sensor & Adapter - BMW N55/N54/S55 (2007...

T#:34885402

Part#: 4BAR TMAP

Back Ordered

$ 139.99 USD

Add to Wish List

Qty

$ 139.99 USD

Add to Wish List

Use these plug and play adapters to quickly adapt a 4bar TMAP sensor to your N54/N55/S55 BMW, raising the boost maximum boost range from 20psi factory up to 43psi.

Vargas N54/55 Billet Crank Seal Guard - BMW N54 N55 3.0L

2X Entries Into Our F80 M3 Sweepstakes

T#:638889

Part#: VTT-CRANKGUARD

In Stock

Starting at $ 89.99 USD

Add to Wish List

Starting at $ 89.99 USD

Add to Wish List

It is a well-known issue on the BMW N54/55 platforms that your serpentine belt can fail for various reasons. When this happens, there is a high chance of the belt getting sucked behind the front damper pulley and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure. Even if you do not lose the engine, it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT, even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Vargas' seal is different from those already on market in two major ways. Firstly, it is not offensively priced. Secondly, it is 100% billet with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long-term corrosion resistance. Crank Seal Guard includes: One VTT Billet N54/55 Crank Seal Guard Two extended 12.9 Grade bolts, and two stainless washers We highly recommend you install WITH a crank bolt capture at the same time, as you have to remove the damper anyway. Then you will get the benefit of helping eliminate the dreaded spun crank hub and the crank seal issue

Show More Show Less

Bav Auto Fuel Level Sensor & Fuel Pump Lock Ring Tool - BMW & MINI ...

10X Entries Into Our F80 M3 Sweepstakes

T#:580400

Part#: B8800089

Ships on Sep 30, 2026

Sale - Save 10% $ 72.99

This product was last offered at the strikethrough price on
05-03-2026

$ 65.69 USD

Add to Wish List

Qty

Sale - Save 10%

$ 72.99

This product was last offered at the strikethrough price on
05-03-2026

$ 65.69 USD

Add to Wish List

Used to remove fuel level and fuel pump lock rings properly to avoid damage.

Spark Plug Gapper Tool BMS Billet

T#:26404907

Part#: 12MMSPG

In Stock

$ 35.00 USD

Add to Wish List

Qty

$ 35.00 USD

Add to Wish List

Spark Plug Gapper Tool BMS Billet is essential for accurately adjusting the gap of spark plugs. This precision tool ensures that each plug is set to the exact specifications required for optimal engine performance. Made in the USA, it features a 12mm plug thread size, making it suitable for a wide range of applications.

Precision Adjustment: Allows for accurate gap adjustments to ensure optimal spark performance and engine efficiency.
Speed and Efficiency: Streamlines the process of gapping plugs while maintaining high precision, saving time and effort.
High-Quality Construction: Crafted from billet materials for durability and reliability, ensuring long-term use.
Lifetime Replacement Program: Comes with a lifetime replacement guarantee, reflecting confidence in the tool's quality and performance.

Upgrade your spark plug maintenance with the Spark Plug Gapper Tool BMS Billet for a reliable and precise solution.

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

2X Entries Into Our F80 M3 Sweepstakes

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Bav Auto Crankshaft Front Oil Seal Removal / Installer Tool - N54, N5...

10X Entries Into Our F80 M3 Sweepstakes

T#:580444

Part#: B8800139

Ships on Sep 30, 2026

Sale - Save 5% $ 203.99

This product was last offered at the strikethrough price on
05-03-2026

$ 193.79 USD

Add to Wish List

Qty

Sale - Save 5%

$ 203.99

This product was last offered at the strikethrough price on
05-03-2026

$ 193.79 USD

Add to Wish List

Used in removal and installation of the front crankshaft seal on BMW N55 engines, a common job that you can save yourself a ton of money doing at home.

VAC Motorsports Crank Seal Guard - N54 N55 S55

T#:29765724

Part#: VAC-11-CSG-N5X

Ships in 8 Business Days

$ 155.99

This product was last offered at the strikethrough price on
05-02-2026

$ 139.99 USD

Add to Wish List

Qty

$ 139.99 USD

Add to Wish List

The VAC Motorsports Crank Seal Guard, made of 6061 Billet Aluminum, prevents your serpentine belt from being pulled into your engine, a common problem amongst BMW N54, N55, and S55 Engines. Without a crank seal guard, the serpentine belt on N54, N55, and S55 engines is commonly sucked into the crank hub area past the crank seal, where it enters your engine and disrupts engine timing. When this occurs, the belt is shredded and clogs engine oil pickup, starving the engine and reducing oil pressure, causing catastrophic engine failure and thousands of dollars worth of damage. VAC Motorsports’ Crank Seal Guards are precision machined for perfect fitment and provide rigidity and maximum protection. We designed our guard with self-locating pilots to perfectly seal the crank hub bore and provide even, minimum clearance around the crank hub. Installation Hardware included. Made in the USA.

Show More Show Less

Bav Auto Fuel Injector Removal/Installation Tool - N55

For E - Chassis N55

10X Entries Into Our F80 M3 Sweepstakes

T#:580388

Part#: B8800075

In Stock

Sale - Save 20% $ 109.99

This product was last offered at the strikethrough price on
05-03-2026

$ 87.99 USD

Add to Wish List

Qty

Sale - Save 20%

$ 109.99

This product was last offered at the strikethrough price on
05-03-2026

$ 87.99 USD

Add to Wish List

This tool takes the stress and difficulty out of removing and installing your N55 fuel injectors.

Bav Auto Timing Tool Kit - N51 N52 N54 N55 S55

10X Entries Into Our F80 M3 Sweepstakes

T#:580414

Part#: B8800107

Ships on Oct 20, 2026

Sale - Save 5% $ 371.99

This product was last offered at the strikethrough price on
05-03-2026

$ 353.39 USD

Add to Wish List

Qty

Sale - Save 5%

$ 371.99

This product was last offered at the strikethrough price on
05-03-2026

$ 353.39 USD

Add to Wish List

Sets cam, valve & VANOS timing on BMW N51, N52, N53, N54 & N55 engines. Includes camshaft fixture with hold-down bolts, 3 alignment gauges and TDC pin. A must when removing and replacing cylinder heads on these engines.

Show More Show Less

URO Solenoid Valve - 11368605123 - N55 N63 S63

2X Entries Into Our F80 M3 Sweepstakes

T#:2181335

Part#: 11368605123

In Stock

$ 109.24 USD

Add to Wish List

Qty

$ 109.24 USD

Add to Wish List

If your VANOS solenoid has failed, you could experience a poor running condition as well as a loss of power. Two required per car.

VAC Motorsports Oil Pan Baffle N55 3.0L Engine

T#:26038565

Part#: VAC-OPB-N55

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

Upgrade your BMW's oil system with the VAC Motorsports N55 Oil Pan Baffle, an essential component for track and street enthusiasts. Engineered to maintain oil surrounding the pick-up at all times, this baffle is crucial for preventing oil pressure loss during hard cornering and acceleration. Trusted by some of the fastest BMWs worldwide, this baffle ensures engine longevity and performance under extreme conditions. Don't risk catastrophic engine failure—equip your BMW with the VAC Motorsports N55 Oil Pan Baffle today.

Benefits:

Prevents significant loss of oil pressure
Vital for track and street use
Ensures engine longevity and performance
Trusted by high-performance BMWs worldwide

Show More Show Less

Bav Auto Fuel Injector Installer / Remover - N20/N55

10X Entries Into Our F80 M3 Sweepstakes

T#:580389

Part#: B8800076

Ships on Oct 20, 2026

Sale - Save 10% $ 106.99

This product was last offered at the strikethrough price on
05-03-2026

$ 96.29 USD

Add to Wish List

Qty

Sale - Save 10%

$ 106.99

This product was last offered at the strikethrough price on
05-03-2026

$ 96.29 USD

Add to Wish List

This enables you to easily remove and install fuel injectors on BMW N20 and N55's produced from 2/2011 and up with direct injection.

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

K&P Engineering High Performance Stainless Steel Micronic Oil Filter ...

T#:402535

Part#: S38

Ships in 6 Business Days

$ 129.00 USD

Add to Wish List

Qty

$ 129.00 USD

Add to Wish List

Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!

The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.

K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top tier product for your European vehicle.

Features:

Consistent filtering across entire filter surface
Superior ASTMF316 filtration performance
Magnetic Prefiltering
Progressive rate bypass combined with high flow characteristics of the filter media avoids unfiltered oil bypassing the filter during cold startup and high rpm
Easy inspection of engine contamination
Proven in Motorsports, Military and Aerospace applications for years. Technology is FAA approved for use in aircraft.

At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.

Watch to learn how to clean a K&P oil filter

This part fits the following BMWs:
2012+ F30 3 Series Sedan 328i 328iX 328i 328iX 335i 335iX
2006 - 2013 E9X 323i 325i 325xi 328i 328xi 330i 330xi 335i 335xi
2010 - 2016 F10 5 Series Sedan 528i 528iX 530i 535i 535iX
2003 - 2006 E60 Sedan 525i 525xi 530i 530xi
2007 - 2010 E60 528i 528xi 535i 535ix
2009 - 2016 E89 Z4 Roadster Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i
2014+ F22 2 Series Coupe 228i 228iX M235i M235iX
2007 - 2013 E88 1 Series Convertible 128i 135i
2008 - 2013 E82 1 Series Coupe 128i 135i 135is 1M Coupe
2012 - 2013 E70 X5 xDrive35d X5 xDrive35i
2007 - 2011 E70 X5 3.0sd X5 3.0si

Show More Show Less

URO Valvetronic Actuator

2X Entries Into Our F80 M3 Sweepstakes

T#:34549585

Part#: 11377603979

In Stock

Sale - Save 15% $ 303.99

This product was last offered at the strikethrough price on
05-03-2026

$ 259.62 USD

Add to Wish List

Qty

Sale - Save 15%

$ 303.99

This product was last offered at the strikethrough price on
05-03-2026

$ 259.62 USD

Add to Wish List

The URO Valvetronic Actuator is a high-quality replacement part for BMW engines, designed to restore precise control over valve timing and lift, enhancing engine performance, fuel efficiency, and responsiveness. Built to meet strict OEM standards, this actuator helps optimize the power and efficiency of BMW engines, making it an ideal solution for maintenance or repair. Available from Turner Motorsport, the URO Valvetronic Actuator ensures a reliable fit and excellent performance for BMW owners.

Restores optimal control over valve timing for enhanced engine efficiency
Improves throttle response and provides smoother acceleration
Contributes to lower emissions and better fuel economy
High-quality construction built for long-lasting durability
Direct-fit replacement compatible with select BMW models
Available from Turner Motorsport, a trusted source for BMW parts

The URO Valvetronic Actuator is a cost-effective replacement that delivers the reliable, high-performance operation BMW owners expect.

Show More Show Less

Rein Valve Cover - BMW N55

2X Entries Into Our F80 M3 Sweepstakes

T#:34114257

Part#: 11127570292

In Stock

Sale - Save 5% $ 254.99

This product was last offered at the strikethrough price on
08-31-2026

$ 242.24 USD

Add to Wish List

Qty

Sale - Save 5%

$ 254.99

This product was last offered at the strikethrough price on
08-31-2026

$ 242.24 USD

Add to Wish List

Valve Cover by Rein is a crucial component designed to protect and seal the top of your BMW’s engine, ensuring optimal performance and preventing oil leaks. Engineered specifically for BMW engines, this high-quality valve cover provides a precise fit and exceptional durability. Available at Turner Motorsport, the Valve Cover by Rein offers long-lasting reliability, protecting critical engine components from damage while maintaining proper oil pressure.

Designed specifically for BMW engines for perfect fit and function
Prevents oil leaks, maintaining proper engine lubrication
Made from high-quality, durable materials for long-lasting performance
Direct-fit replacement ensures hassle-free installation
Protects critical engine components and improves engine efficiency
Helps maintain proper oil pressure for optimal engine performance

The Valve Cover VCE0101 by Rein from Turner Motorsport is the ideal solution for BMW owners seeking to protect their engine, prevent oil leaks, and ensure reliable performance.

Show More Show Less

Bav Auto Fuel Injector Seal Installer & Remover - N54/N63

10X Entries Into Our F80 M3 Sweepstakes

T#:580445

Part#: B8800140

In Stock

Sale - Save 3% $ 121.99

This product was last offered at the strikethrough price on
05-03-2026

$ 118.33 USD

Add to Wish List

Qty

Sale - Save 3%

$ 121.99

This product was last offered at the strikethrough price on
05-03-2026

$ 118.33 USD

Add to Wish List

This is has been specifically designed to remove and install the seals on your fuel injectors without damaging either the seals or injectors themselves.

Large Aluminum Oil Catch Can

T#:597051

Part#: MMOCCLA

In Stock

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Bav Auto Media Blaster Kit - BMW N20 N54 N55

10X Entries Into Our F80 M3 Sweepstakes

T#:582473

Part#: B1100008

In Stock

Sale - Save 8% $ 329.99

This product was last offered at the strikethrough price on
05-03-2026

$ 303.26 USD

Add to Wish List

Qty

Sale - Save 8%

$ 329.99

This product was last offered at the strikethrough price on
05-03-2026

$ 303.26 USD

Add to Wish List

Carbon building up in your intake ports? Take care of it quick and easy with this DIY media blaster kit from Bav auto. This walnut shell media blaster kit contains everything you need to effectively clean and de-carbon the intake ports and valves on your turbocharged N20, N54, or N55 BMW engine. Taking your vehicle to the dealer to have this service performed, you would be looking at a cost of around $1000 or more! This kit saves you money and can be used as many times as you need to ensure perfectly clean intake ports for optimum airflow and performance. Included in this kit: 20lb pressure feed media blaster including water separator and pressure gauge blasting wand N54/N55 port adapter (attaches to your shop vac to catch the used media and deposits) 25lb package of walnut shell blasting media Use of this kit requires a medium sized air compressor (suggested minimum 20-30 gallon tank, 4.0 CFM @ 90psi), common "shop vac" and full hearing and eye protection. We recommend the use of a remote starter switch. Please note: Intake manifold gasket set and Throttle body gasket, sold separately, must be replaced when removing intake manifold.

Show More Show Less

Vargas Ignition Coil Kit (Blue) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309605

Part#: VTT-COIL-N5X-BLU

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

Valve Cover Gasket - Set

2X Entries Into Our F80 M3 Sweepstakes

T#:586660

Part#: 11127587804

In Stock

$ 22.99 USD

Add to Wish List

Qty

$ 22.99 USD

Add to Wish List

URO Manifold Absolute Pressure (MAP) Sensor - BMW N54 N20 N26 S55 S63...

2X Entries Into Our F80 M3 Sweepstakes

T#:36032311

Part#: 13628644433

In Stock

$ 71.99 USD

Add to Wish List

Qty

$ 71.99 USD

Add to Wish List

The MAP sensor, or manifold absolute pressure sensor, works with the engine computer to set the fuel curve and give readings to the engine computer. If yours is faulty, it may cause improper running, rich or lean fuel curves, or other general performance issues. Replace yours with this unit to keep your engine running at full potential. For N54 applications, you will need adapter harness T#583821- This TMAP sensor is typically used in high-boost applications for the N54

Show More Show Less

URO Positive Cable Battery Connection Pole

2X Entries Into Our F80 M3 Sweepstakes

T#:42436713

Part#: 61129217031

In Stock

$ 130.99 USD

Add to Wish List

Qty

$ 130.99 USD

Add to Wish List

If your BMW has been in an accident and the Battery Safety Terminal (BST) has been triggered, you'll need a new positive battery cable connection to restore power and get the vehicle running again.

Vargas Ignition Coil Kit (Red) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309610

Part#: VTT-COIL-N5X-RED

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

Bav Auto Crankshaft Rear Oil Seal Removal / Installer Tool - N51, N52...

10X Entries Into Our F80 M3 Sweepstakes

T#:580412

Part#: B8800104

In Stock

Sale - Save 5% $ 147.99

This product was last offered at the strikethrough price on
05-03-2026

$ 140.59 USD

Add to Wish List

Qty

Sale - Save 5%

$ 147.99

This product was last offered at the strikethrough price on
05-03-2026

$ 140.59 USD

Add to Wish List

For removal and installation of the rear crankshaft seal on BMW N51, N52 and N54 engines.

Borescope Camera with Light For Phone

10X Entries Into Our F80 M3 Sweepstakes

T#:32450134

Part#: PHONEBORESCOPE

In Stock

Sale - Save 3% $ 58.99

This product was last offered at the strikethrough price on
05-03-2026

$ 57.22 USD

Add to Wish List

Qty

Sale - Save 3%

$ 58.99

This product was last offered at the strikethrough price on
05-03-2026

$ 57.22 USD

Add to Wish List

The Borescope Inspection Camera offers 1920P HD resolution, a flexible 7.9mm probe, and a 16.4ft semi-rigid cable, making it ideal for inspecting hard-to-reach areas. Easily connect to IOS and Android devices, and use the IP67 waterproof probe for various applications, including automotive, plumbing, and home inspections.

Key Features:

1920P HD Resolution: Capture clear images and high-quality video at 1920x1440 resolution.
Easy Connection: Connect quickly to IOS 9.0+ and Android 7+ devices via the 'SUP-ANESOK' app.
Semi-Rigid Cable: 16.4ft cable offers a mix of flexibility and rigidity for precise inspections.
Waterproof Probe: IP67-rated, capable of operating underwater up to 3.28 feet for 1 hour.
Wide Applications: Suitable for automotive, plumbing, and home inspections, with adjustable brightness for low-light environments.

Includes:

Borescope Camera
Android Adapter
Lightning Port Adapter
USB Type-C Connector
16.4 ft. Semi-Rigid Cable
Magnet
Hook
Mirror
Protective Cap
Manual

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Show More Show Less

Bav Auto Intermediate Lever Valve Spring Compressor - N20/26 N55 ...

10X Entries Into Our F80 M3 Sweepstakes

T#:580431

Part#: B8800124

Ships on Sep 30, 2026

Sale - Save 15% $ 178.99

This product was last offered at the strikethrough price on
05-03-2026

$ 152.14 USD

Add to Wish List

Qty

Sale - Save 15%

$ 178.99

This product was last offered at the strikethrough price on
05-03-2026

$ 152.14 USD

Add to Wish List

For installation and removal of pressure springs on intermediate levers of valve train. Ensures quick, easy and safe handling of these high force springs.

URO Power Distribution Box With Fuse - BMW E8X 1

2X Entries Into Our F80 M3 Sweepstakes

T#:49822552

Part#: 61146971370

Back Ordered

$ 91.99 USD

Add to Wish List

Qty

$ 91.99 USD

Add to Wish List

Ensures the appropriate amount of power is sent to electrical vehicle components.

Bav Auto Oil Filter Housing Cap Removal Tool - 1/2" Drive

10X Entries Into Our F80 M3 Sweepstakes

T#:580338

Part#: B8800006

In Stock

Sale - Save 25% $ 33.99

This product was last offered at the strikethrough price on
05-03-2026

$ 25.49 USD

Add to Wish List

Qty

Sale - Save 25%

$ 33.99

This product was last offered at the strikethrough price on
05-03-2026

$ 25.49 USD

Add to Wish List

Used to easily remove your oil filter housing cap without damaging it.

Bav Auto Torx head bolt socket - E12

10X Entries Into Our F80 M3 Sweepstakes

T#:580351

Part#: B8800022

Ships on Sep 30, 2026

Sale - Save 25% $ 31.99

This product was last offered at the strikethrough price on
05-03-2026

$ 23.99 USD

Add to Wish List

Qty

Sale - Save 25%

$ 31.99

This product was last offered at the strikethrough price on
05-03-2026

$ 23.99 USD

Add to Wish List

This special long, thin, Torx socket is required for removal and installation of the head bolts on most BMWs with twin-cam cylinder heads. 1/2" drive

Rein Fuel Injection Fuel Feed Pipe

2X Entries Into Our F80 M3 Sweepstakes

T#:17738375

Part#: 13537585426

In Stock

Sale - Save 5% $ 44.99

This product was last offered at the strikethrough price on
08-31-2026

$ 42.74 USD

Add to Wish List

Qty

Sale - Save 5%

$ 44.99

This product was last offered at the strikethrough price on
08-31-2026

$ 42.74 USD

Add to Wish List

Ensures that proper pressure is maintained between the high-pressure fuel pump and fuel rail.

Oil Pan Gasket - Multiple BMWs

2X Entries Into Our F80 M3 Sweepstakes

T#:24145943

Part#: 11137600482

In Stock

$ 25.57 USD

Add to Wish List

Qty

$ 25.57 USD

Add to Wish List

Replace your worn out and leaking oil pan gasket and avoid having to top off between oil changes.

IWIS N55 Engine Oil Pump Chain Kit - BMW E82/88 E9X F3X F25 F26 E70/7...

T#:36981080

Part#: 90001301

In Stock

$ 314.36

This product was last offered at the strikethrough price on
05-04-2026

$ 304.83 USD

Add to Wish List

Qty

$ 304.83 USD

Add to Wish List

Prevent costly failure with this IWIS Engine Oil Pump Chain Kit! This kit contains all of the basic items needed to service your oil pump drive system and prevent failure long before it occurs. Chains can stretch and chain guides and tensioners can wear out, leading to the chain skipping teeth. This prevents the oil pump from being driven at the proper speeds. If not addressed, the chain could begin to "slip" over the gears, failing to drive the oil pump. When this occurs, oil pressure will drop suddenly, failing to properly lubricate sensitive internal engine components such as main bearings, rod bearings, and camshaft ledges and lobes, resulting in severe scoring and eventual engine failure.

Show More Show Less

URO Turbocharger Oil Feed Line - BMW N20 2.0L

2X Entries Into Our F80 M3 Sweepstakes

T#:53079361

Part#: 11428678840

In Stock

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

Supplies oil to the turbocharger, ensuring proper lubrication of the bearings.

Mishimoto Universal Catch Can Kit - Carbon Fiber

T#:372557

Part#: MMOCCCF

In Stock

$ 162.99 USD

Add to Wish List

Qty

$ 162.99 USD

Add to Wish List

Universal kit with a catch can and rubber hose; for retrofitting on a variety of vehicles. Carbon fiber catch can prevents a harmful buildup of oil inside of the turbocharger, intake manifold, intercooler and piping. Separates oil particles from PCV/CCV air Defends intercooler, intake system, and essential components from oil blow-by Made from lightweight carbon fiber Compact design makes for easy engine bay placement Checking fluid levels made easy with built in sight tube Comes complete with mounting bracket, hose, all necessary clamps, fittings, and mounting hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

URO Oil Level Sensor W/ O-Ring - BMW N52 N54 N55 N62 N63 S85 S65 S54 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:43750194

Part#: 12617607910

In Stock

$ 192.99 USD

Add to Wish List

Qty

$ 192.99 USD

Add to Wish List

The engine oil level sensor continuously monitors the oil level in the engine's oil pan, transmitting real-time data to the vehicle's ECU (Engine Control Unit). This critical information helps ensure that the engine maintains the proper amount of oil for optimal lubrication. Commonly found in modern vehicles, the oil level sensor serves as an added safeguard against low oil levels, preventing potential engine damage.

Show More Show Less

AutoTecknic Dry Carbon Competition Oil Cap Cover - Type 1 - For Vario...

T#:39971047

Part#: BM-0007

In Stock

$ 64.99 USD

Add to Wish List

Qty

$ 64.99 USD

Add to Wish List

a precision-engineered, lightweight dry carbon fiber upgrade designed to enhance the engine bay of compatible BMW models with an aggressive motorsport look and easy OEM-style installation.

Transmission Oil Cooler - Heat Exchanger

2X Entries Into Our F80 M3 Sweepstakes

T#:20617630

Part#: 17217536929

In Stock

$ 115.85 USD

Add to Wish List

Qty

$ 115.85 USD

Add to Wish List

An OE automatic transmission oil cooler heat exchanger for your BMW will guarantee proper fitment. This heat exchanger will keep your BMW's transmission oil cool. Corrosion-resistant, high-strength materials ensure reliable leak-free ATF cooling performance. Manufactured to OE transmission oil cooler dimensions for proper clearances and easy bolt-on installation.

Show More Show Less

IWIS Chain Tensioner - With Gasket Ring - BMW N52 N54 N55 3.0L ...

T#:43378595

Part#: 11317584723

Ships in 3 Business Days

$ 100.99

This product was last offered at the strikethrough price on
05-07-2026

$ 97.99 USD

Add to Wish List

Qty

$ 97.99 USD

Add to Wish List

Over time, your engine timing components begin to wear out. Tensioners weaken, chains can stretch, and timing chain guides can wear down. All of these lead to the possibility of the timing chain jumping teeth on the sprockets, causing your timing to shift. This could result in rough idle and reduced engine power, or even complete engine failure. Prevent damage to your engine with new timing components, such as this IWIS timing chain tensioner. Note, we recommend replacing timing components every 100K miles, or sooner, depending on the condition of the timing components.

Show More Show Less

MMX Performance - 4-Pin One-Piece Crank Hub Upgrade Kit - With MMR Ca...

T#:45039725

Part#: MMR20-1004FK

Ships in 4 Business Days

$ 1,227.99 USD

Add to Wish List

Qty

$ 1,227.99 USD

Add to Wish List

The centerpiece of this MMX kit is the UK-made CNC-machined one-piece crank hub, created from billet EN36 steel that's heat-treated with a 0.75mm case hardening, making it incredibly strong and durable. Included are four aerospace precision-machined dowels that mechanically lock the hub to the end of the crank itself, plus a brand new OE bolt. Installation of these dowels is certainly not a DIY job. But, to make the job easier for the professionals, ensuring that the required crank modifications are made safely and accurately, the MMX kit also includes a full installation jig that includes a bolt-on drilling guide, a location bolt for this guide, plus an HSS rolled high-speed drill bit. Together, the single-piece design combined with the four-pin location ensures that there is simply no way that the friction plates can ever slip. With the new OE crank bolt tightened appropriately, this delivers a transformational improvement in reliability and peace of mind versus the OE version. Also included is the MMR Crank Bolt Capture Plate. This adds one additional layer of defense, preventing the crank bolt from being able to back out and loosen over time, ensuring everything is tightly held together as intended.

Show More Show Less

BMW N54 N55 Oil Cooler Valve - Red Burger Motorsport Sport (4/2007+) ...

For vehicles with a production date of 04/2007+

T#:588633

Part#: OILVALVE-RED

Ships in 3 Business Days

$ 59.00 USD

Add to Wish List

Qty

$ 59.00 USD

Add to Wish List

This simple engine oil cooler valve from Burger Motorsports increases flow to your fender mounted engine oil/air heat exchanger resulting in lower engine oil temperatures and more consistent performance during heavy throttle. Less restrictive than the spring-loaded units. Installs in minutes and is fully reversible. CNC machined for a precise fit and anodized for protection. Made in the USA. Requires BMW's external sport engine oil cooler which is standard on most 2008+ models, optional on 2007 E9x models. FEATURES AND BENEFITS Easily lower engine oil temperature Stock oil cooler will work more efficient More consistent performance CNC Machined for a perfect fit Made in USA

Show More Show Less

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733531

Part#: VTT-CRANKHUB-5

Ships on Sep 17, 2026

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Improved Racing BMW Oil Cooler Thermostat (180F)

T#:27171935

Part#: IRTHERM

Back Ordered

Starting at $ 318.99 USD

Add to Wish List

Starting at $ 318.99 USD

Add to Wish List

Precise Oil Temperature Control for Your BMW Upgrade your BMW N20, N26, N51, N52, N53, N54, N55, and S55 engine's oil temperature control with Improved Racing's high-performance oil cooler adapter. Designed to address flaws in the factory's restrictive oil cooler adapter and faulty internal flow control valve, this upgrade ensures precise oil temperature control. Improved Racing's thermostat provides quick engine warmup, prevents overcooling, and delivers full oil cooling capacity on demand. Trusted by professional race teams around the globe, Improved Racing's thermostats have proven highly reliable, are backed by a lifetime warranty, and are made in the USA. Option to Use the Factory Oil Cooler and Lines The optional factory oil line adapter allows you to use the factory oil cooler lines for a simple, plug-and-play installation. For maximum performance, the factory oil cooler and lines may be replaced with an aftermarket cooler and AN lines using the AN adapter fittings (-10AN line size is recommended). Please note that some applications, such as most BMW SUV's, use a water-to-oil heat exchangers. These applications require plugging the coolant supply and return ports, as well as adding an external air-to-oil cooler and lines (factory or aftermarket). Please note the Oil cooler adapter cannot be used without an oil cooler.

Show More Show Less

MMX Oil Filter Housing - Black

T#:4552065

Part#: MMR03-0101-BL

Ships in 10 Business Days

$ 142.99 USD

Add to Wish List

Qty

$ 142.99 USD

Add to Wish List

If you are looking for peace of mind over the prone to cracking OEM plastic housing cap, this oil filter housing cap by MMX may be exactly what you are looking for. Composed of billet aluminum, this cap is light, durable, and dresses up your engine bay! Comes finished with a polished anodized dark anthracite coating. Installation is simple as it can be replaced while completing an oil change. *Note: After exposure to excessive heat over prolonged periods, overall finish fading can occur.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW X Series E84 (2013-2015)

Sub-Categories

Benefits:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results