PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

This caliper bushing kit will eliminate flex caused by weak rubber caliper bushings. As the brake pedal is pressed the caliper grabs the rotor and twists on its mounting bushings. The rubber bushings allow the caliper to deflect and twist which affects pedal feel and results in uneven pad wear. These solid brass bushings will not twist or deflect so your calipers can squeeze the pads evenly on both sides of the rotor (sort of like what multi-piston big brakes do). This will give you much longer pad life and a more consistent pedal feel. This is the most complete kit we have ever sold with stainless steel caliper slide bolts, o-rings, and new dust boots. Unlike other kits, these bushings are pressed into the caliper and will not shift or slide on their own.

Installation is straightforward: remove the old rubber bushings and press in the new brass bushings (we recommend special tool 003326ECS03). High temp caliper grease or anti-seize is required. The new bushings include an inner o-ring that helps trap grease on the slide bolt, reducing friction and wear.

***Click here for installation instructions*** 

***Click here for the installation tool***

For most models with floating calipers. Fits the rear of E90/2 and E60, but for the front you'll need the kit found here. Does not fit E30 models with Girling calipers, but is compatible with Ate calipers. 

These 2-piece floating rotors help dissipate heat better than a standard cast iron rotor and are also lighter for less unsprung weight. Managing heat in the brake system is vital to braking performance, especially on the track or when driven hard. It's why your brake rotors have internal vanes that vent heat as the rotor spins. These 2-piece ECS rotors feature an outer cast iron friction surface ring that is separate from the aluminum center hat. This allows better airflow through the vanes and for the friction ring can expand as it gets hot. The rotors are also cross-drilled for better ventilation and slotted to improve brake pad performance.

ECS 2-Piece Rotors feature:

• Aluminum hats for light weight
• Heat-treated cast iron friction rings
• 2-piece assembly improves brake cooling
• Anti-corrosion coating on non-friction surfaces and hard anodizing on rotor hat

These are the same size as the stock rotors so your stock caliper and mounting bracket will fit and there will be no clearance issues with your wheels or to other components. Stainless steel rotor retaining screws are included. You can use these with any brake pad.

Price is for the pair of brake rotors.

This item fits the following BMWs:
2008-2013 E82 E88 BMW 135i

Fits the following with M Performance Brakes:
2006-2011 E90 BMW 325i 328i 330i - Sedan
2007-2011 E91 BMW 325i 328i - Touring Wagon
2007-2013 E92 BMW 328i - Coupe
2007-2013 E93 BMW 328i - Convertible

This caliper bushing kit will eliminate flex caused by weak rubber caliper bushings. As the brake pedal is pressed the caliper grabs the rotor and twists on its mounting bushings. The rubber bushings allow the caliper to deflect and twist which affects pedal feel and results in uneven pad wear. These solid brass bushings will not twist or deflect so your calipers can squeeze the pads evenly on both sides of the rotor (sort of like what multi-piston big brakes do). This will give you much longer pad life and a more consistent pedal feel. This is the most complete kit we have ever sold with stainless steel caliper slide bolts, o-rings, and new dust boots. Unlike other kits, these bushings are pressed into the caliper and will not shift or slide on their own.

Installation is straightforward: remove the old rubber bushings and press in the new brass bushings (we recommend special tool 003326ECS03). High temp caliper grease or anti-seize is required. The new bushings include an inner o-ring that helps trap grease on the slide bolt, reducing friction and wear.

***Click here for installation instructions*** 

***Click here for the installation tool***

For front calipers on E90/2 and E60. For rear calipers and all caliper on other models, click here. 

These 2-piece floating rotors help dissipate heat better than a standard cast iron rotor and are also lighter for less unsprung weight. Managing heat in the brake system is vital to braking performance, especially on the track or when driven hard. It's why your brake rotors have internal vanes that vent heat as the rotor spins. These 2-piece ECS rotors feature an outer cast iron friction surface ring that is separate from the aluminum center hat. This allows better airflow through the vanes and for the friction ring can expand as it gets hot. The rotors are also cross-drilled for better ventilation and slotted to improve brake pad performance.

ECS 2-Piece Rotors feature:

• Aluminum hats for light weight
• Heat-treated cast iron friction rings
• 2-piece assembly improves brake cooling
• Anti-corrosion coating on non-friction surfaces and hard anodizing on rotor hat

These are the same size as the stock rotors so your stock caliper and mounting bracket will fit and there will be no clearance issues with your wheels or to other components. Stainless steel rotor retaining screws are included. You can use these with any brake pad.

Price is for the pair of brake rotors.

This item fits the following BMWs:
2011 E82 E88 BMW 1M Coupe
2008-2013 E90 E92 E93 BMW M3 Sedan, Coupe, Convertible

The latest in the Yellow line takes all of the RSL29 characteristics and adds a bit more aggressive behavior. Friction levels go up for more initial bite and better fade resistance. Modulation and release stays close to RSL29 levels. Pad and rotor wear is a little more than on the previous Yellows but still within reasonable levels and the RSL1 is still considered an extended endurance pad. Its development stemming from GT classes at Le Mans and Nürburgring.

Since Pagid pads tend to "out-gas" we recommend using these pads with a new gas-slotted or cross-drilled rotor for the best performance. Pagid brake pads are not compatible with previously used rotors, especially if used with a carbon or Kevlar based race pad.

This item fits the following BMWs:
2011+ E82 BMW 1M Coupe
2004-2005 E60 BMW 525i (automatic transmission only)
2006-2007 E60 BMW 525i, 525xi (all transmissions)
2008-2010 E60 BMW 528i, 528xi
2004-2007 E60 BMW 530i, 530xi
2008-2010 E60 BMW 535i, 535xi
2004-2010 E60 BMW 545i, 550i
2004-2010 E63 BMW 645Ci, 650Ci
2002-2008 E65 BMW 745i, 745Li, 750i, 750Li, 760Li
2007-2013 E9X BMW 335i, 335Xi, 335d
2008-2013 E9X BMW M3

The RSL29 pad is an endurance racing compound with long life and great wear characteristics. It has stable friction over a broad temperature range which makes them a very easy to use and predictable braking pad in a lot of environments. An evolution of the RSL19 endurance pad designed for more advanced drivers. This compound combines the outstanding wear rate of the RSL19 with a slightly higher coefficient of friction and initial bite. RSL29 also features improved hot fade resistance over the RSL19. In addition to the endurance racing, this pad will also be found in GT and VLN classes and Touring Cars (including our own E46 World Challenge cars). BMW has been using Pagid Yellow pads on their Nurburgring test vehicles and Ring Taxi for years.

This is the set of Rear pads.

This item fits the following BMWs:
2004-2010 E60 BMW 535i 545i 550i M5
2004-2011 E63 E64 BMW 645ci 650i M6
2011+ E82 BMW 1M - Coupe
2008-2013 E90 BMW M3 - Sedan
2008-2013 E92 BMW M3 - Coupe
2008-2013 E93 BMW M3 - Convertible

These 2-piece floating rotors help dissipate heat better than a standard cast iron rotor and are also lighter for less unsprung weight. Managing heat in the brake system is vital to braking performance, especially on the track or when driven hard. It's why your brake rotors have internal vanes that vent heat as the rotor spins. These 2-piece ECS rotors feature an outer cast iron friction surface ring that is separate from the aluminum center hat. This allows better airflow through the vanes and for the friction ring can expand as it gets hot. The rotors are also cross-drilled for better ventilation and slotted to improve brake pad performance.

ECS 2-Piece Rotors feature:

• Aluminum hats for light weight
• Heat-treated cast iron friction rings
• 2-piece assembly improves brake cooling
• Anti-corrosion coating on non-friction surfaces and hard anodizing on rotor hat

These are the same size as the stock rotors so your stock caliper and mounting bracket will fit and there will be no clearance issues with your wheels or to other components. Stainless steel rotor retaining screws are included. You can use these with any brake pad.

Price is for the pair of brake rotors.

This item fits the following BMWs:
2006-2011 E90 BMW 335d 335i 335xi - Sedan
2007-2013 E92 BMW 335i 335is 335xi - Coupe
2007-2013 E93 BMW 335i 335is - Convertible
2012-2015 E84 BMW X1 xDrive35i

BMW E84 E9X Rear Slotted Brake Rotors - Pair (336x22): Upgrade Your BMW's Braking Performance

• Enhances brake cooling and reduces brake fade
• Improves braking response and overall stopping power
• Reduces brake pad wear for extended pad life
• Provides a stylish appearance with slotted design

Upgrade the braking performance of your BMW with the BMW E84 E9X Rear Slotted Brake Rotors. These brake rotors are specifically designed to fit BMW E84 and E9X models, providing enhanced braking performance and durability. With a slotted design, they help improve brake cooling, reduce brake fade, and enhance overall stopping power. Additionally, they reduce brake pad wear for extended pad life, saving you money on replacement pads in the long run. Plus, their stylish appearance adds a sporty touch to your BMW's exterior. Access Secret Premium Dashboard