BMW Engine Parts for BMW 3 Series E91 (2006-2012)

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

• All-in-one valve cover overhaul
• Preventative replacement saves time and trouble later on
• Includes new oil separator system
• Replace valve cover gaskets before a leak becomes worse
• Replace valve cover before it cracks

For the 2007 model year BMW switched to a plastic valve cover on the N51 and N52 engines. As we have seen over time the plastic can crack which leads to oil leaks, vacuum leaks, poor running, and other issues. Unfortunately, it's not just the gasket that needs periodic replacement but the entire valve cover itself. This kit includes a new valve cover, gaskets, eccentric shaft seal, and hardware. The valve cover also incorporates the oil separator which is not a replaceable item on its own. So a complete valve cover replacement will tackle multiple problem areas at once. The valve cover is the same for N51 SULEV and N52 engines.

Cracked Valve Cover. The plastic used for the N52 valve cover is thin and weak in certain spots. This makes it prone to hairline or larger cracks that will leak oil and cause vacuum leaks. You might also notice rough running, especially at idle. Often a technician will go looking for a failed ignition coil, spark plug, or failed vacuum hose on the engine. And without a fault code to assist in diagnosis this can often mean wasted time and money. A cracked valve cover is a new problem area that many techs don't think to check.

Oil Separator/Crankcase Vent. BMW integrated the oil separator system into the valve cover on these later engines. An internal manifold creates a cyclone effect and centrifugal force separates vapor from the liquid oil. The liquid oil is supposed to drain through the valve cover and back to the oil pan while the remaining vapor is burned up during combustion. It's a very efficient and environmentally-friendly design with very few moving parts. Unfortunately it's not perfect and eventually the internal passageways will become clogged. This problem is made worse in cars that have short drive cycles, sit for long periods of time, do not have frequent oil changes, do not see regular runs to redline, and cars in freezing climates. If the engine never reaches optimal operating temp the oil remains in liquid form or becomes sludge. This is bad news for the entire engine, leading to fouled spark plugs, rough running and misfires and even premature failure of catalytic converters and oxygen sensors. Since the oil separator system in the valve cover is not available on its own, and cleaning it is nearly impossible, the complete replacement of the valve cover is the only option. Other oil vent tubes and vacuum hoses are also recommended to get replaced at the same time.

Valve Cover Gaskets. As with any rubber part, failures occur when the rubber becomes dry and brittle. The pliable rubber no longer forms a seal between the cylinder head and valve cover where it will develop an oil leak. Valve cover gaskets that leak can allow oil to seep into the spark plug holes and contaminate ignition coil boots and plugs. That can lead to rough running and misfires. A new valve cover includes new gaskets.

Eccentric Shaft Seal. The seal for the eccentric shaft sensor is a known spot for oil leaks. When the seal to the valve cover fails oil can end up in the sensor itself and ruin the sensor (an unecessary $300 expense). Usually a new seal (o-ring) will stop the leaks but sometimes the valve cover is at fault too. A new eccentric shaft seal is included.

All new hardware is included to avoid re-using and over-tightening the original bolts (they have a very low torque rating).

Replacement requires accessing the rear of the engine with a lot of the upper plastic shrouding removed. The vent hose on the valve cover should be replaced as it is almost always broken anyway (#11157559528). The metal fuel line must also be removed and disconnected from the fuel injectors. Professional installation is encouraged if you have never done this kind of work before. Serious DIY types should have a Bentley Service Manual to use which greatly explains the process. You may also want to combine this work with the oil filter housing gasket replacement.

There is no maintenance or replacement interval for the N52 valve cover. However, we have seen cracks and other failures in the 50,000-90,000 mile range. Our best advice is to plan on a major top end overhaul around the 70-80,000 mile mark. There's no mechanical downside to replacing it as prevention and it will make the engine run better and last longer.

This item fits the following BMWs:
2008-2012 E82 BMW 128i
2007-2011 E90 BMW 328i 328xi 328i xDrive - Sedan
2007-2012 E91 BMW 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2008-2010 E60 BMW 528i 528xi 528i xDrive
2011 F10 BMW 528i
2007-2010 E83 BMW X3 3.0i X3 3.0si
2007-2008 E70 BMW X5 3.0si
2007-2008 E85 BMW Z4 3.0i Z4 3.0si
2009-2010 Z4 BMW Z4 sDrive30i

Optimize your vehicle's performance and shield crucial components with the Mishimoto Compact 2-Port Baffled Oil Catch Can. This innovative solution effectively separates oil particles from PCV/CCV air using a 50-micron bronze filter, ensuring defense against oil blow-by for your intercooler, intake system, and vital parts. Constructed with a patented billet 6061 aluminum can sealed with Viton™ O-Rings, this catch can guarantees both durability and effectiveness.

Equipped with a universal mounting bracket, it allows adaptable installation and comes complete with two CNC-machined aluminum 1/2" barbed hose fittings. With an enhanced 3 oz internal capacity, service intervals are prolonged, while its fully serviceable filter and can ensure enduring functionality.

Engineered for safety in pressurized applications, the internal air diverter enhances oil separation by amplifying air turbulence. Available in black, red, or polished finishes, this catch can preserves proper octane levels, reducing potential detonation and promoting extended engine life.

The product package includes the Compact 2-Port Baffled Oil Catch Can, two Aluminum 1/2" Barbed Fittings, and a Universal Mounting Bracket, all backed by the Mishimoto Lifetime Warranty.

WARNING! Prop 65 may apply to this product.

Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to all companies selling products in California.

Prop 65 mandates listing any chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm.

For more information about California Prop 65 warning, visit: www.P65Warnings.ca.gov.

The cutting-edge GENIUS1 is a powerhouse among our chargers renowned for its exceptional performance, energy efficiency, and compact design. The GENIUS1 is a versatile 6-volt and 12-volt charger, maintainer, and desulfator with a 1-amp rating. It's engineered to work with lead-acid batteries in automotive, marine, and deep-cycle applications, supporting flooded, gel, AGM, maintenance-free types, and even lithium-ion batteries.

Features: 

• Do more with Genius - Designed for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries.
• Enjoy precision charging - An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
• Charge dead batteries - Charges dead batteries as low as 1-volt. Or use the all-new Force Mode that allows you to take control and manually begin charging dead batteries down to zero volts.
• Simple to set up and use - Plug-in, connect to the battery, select a charge mode, and start charging your battery. A fully-automatic, worry-free battery charger for year-round use.
• Restore your battery - Detects sulfation and acid stratification and restores lost performance for stronger engine starts and extended battery life.
• Compatible with all types of vehicles - Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, hot rods, and more - you name it.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

The Gen V WG38 Ultra-Gate 38 external wastegate is your cost-effective, high-performance solution. This 38mm external wastegate is meticulously designed for hassle-free bolt-on applications that make use of the 2-bolt flange.

The 6 Piece Stubby XZN Triple Square Driver Set features 1/4" square drive drivers designed for impact, ensuring consistent performance across sizes from 4mm to 12mm. Crafted from durable S2 Steel and fully heat-treated, these drivers are robust and prepared for any task at hand.

Their satin chrome plated finish not only prolongs their lifespan but also adds a professional touch to your toolkit. What sets these drivers apart is their compact one-piece design, enhancing ease of handling and storage.

These stubby XZN drivers arrive neatly organized on a 4" Magrail TL Magnetic Socket Organizer, ensuring they're always at your fingertips. Plus, they come with the assurance of our LIFETIME REPLACEMENT program, providing you with confidence in your investment. This set equips you with the perfect XZN sockets, even for those snug spaces.

Includes:

• 4" Magrail TL Magnetic Socket Organizer
• 4 mm
• 5 mm
• 6 mm
• 8 mm
• 10 mm
• 12 mm

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

The eccentric shaft sensor plays a vital role in controlling valvetronic timing and is often a common issue in BMW vehicles. If you've noticed difficult starts, reduced fuel economy, and overall engine power and performance issues, this component could be the culprit.

Key Features:

Guaranteed Fitment: Designed to fit perfectly, ensuring compatibility with your vehicle. Accurate Positioning: Provides precise shaft position control, even at high RPMs. Direct OE Replacement: Easy to install with its direct-fit design, saving time and effort. Low Electrical Resistance: Alloy connector conductors minimize resistance, ensuring accurate signal transmission. Upgrade to this quality replacement eccentric shaft sensor to restore optimal engine performance and address the symptoms associated with a faulty sensor.

Modern emission regulations require a closed PCV/Breather system for cleaner operation. However, inefficient oil particle capture can lead to excessive oil vapor ingestion, causing carbon buildup, reduced performance, and fuel economy. ECS Tuning's updated ECS Baffled Oil Catch Can, now with an easy-to-empty 1/4" drain fitting, is engineered to collect toxic blow-by gases, minimize carbon deposits, and reduce oil contamination within engine oil. Recirculating oil vapor ensures emissions compliance without venting to the atmosphere.

• Key Features:
• Highly Efficient Oil Separator: Strategically positioned 4 chamber baffle system maximizes oil/air separation and minimizes oil droplets in the intake tract.
• Integrated Dipstick: Knurled and black anodized oil dipstick simplifies oil volume inspection.
• Reservoir: Available in 6oz or 8oz capacity with a 1/4" NPT drain plug fitting.
• Serviceable: Easily removable baffle plates and drain plug for cleaning.
• Easy/Customizable Installation: Combine with the ECS Universal Bracket Kit for simplified installation and adjustable mounting locations.
• Leak-Free Fittings: Machined -10AN ORB (O-Ring Boss) fittings available for secure connections (fittings sold separately).