BMW Fuel System Parts for BMW 3 Series E93 (2007-2013)

BMW B46 B48 B58 Motiv ReFlex 0-10 Bar Pressure Sensor

T#:28537533

Part#: 101-0216

In Stock

$ 105.00 USD

Add to Wish List

Qty

$ 105.00 USD

Add to Wish List

BMW B46 B48 B58 Motiv ReFlex 0-10 Bar Pressure Sensor is designed for accurate measurement of fluid and air pressure in high-performance applications. Ideal for monitoring a variety of pressures including fuel, boost, coolant, and oil, this sensor provides crucial data for optimizing vehicle performance.

Featuring a 2-Pin DTM connector, this sensor offers a direct plug-and-play connection to the ReFlex+ harness, ensuring a seamless integration with flash platforms via CANbus. Each ReFlex+ unit can support up to two of these sensors, allowing for comprehensive monitoring.

Versatile Measurement: Capable of measuring fuel pressure, boost, coolant, oil, and other fluids.
Easy Integration: 2-Pin DTM connector provides a direct plug-and-play connection.
Comprehensive Monitoring: Supports integration of up to two sensors per ReFlex+ unit.
High-Performance Design: Designed to handle high pressures and deliver accurate readings.

For optimal installation, consider using the 3/8 Female to 3/8 Male SAE Quick Disconnect Adapter with a 1/8" NPT port on an ethanol sensor or the 5/16 Female to 5/16 Male SAE Quick Disconnect Adapter with a 1/8" NPT port on a factory fuel line. Please note that the ethanol sensor is not included.

Show More Show Less

BMW B46 B48 Motiv ReFlex Plug-n-Play Ethanol Sensor Harness

For Vehicles With Motiv ReFlex Unit Currently Installed Only

T#:22723690

Part#: 101-0212

In Stock

$ 49.00 USD

Add to Wish List

Qty

$ 49.00 USD

Add to Wish List

BMW B46 B48 Motiv ReFlex Plug-n-Play Ethanol Sensor Harness simplifies the integration of an ethanol content sensor into your BMW's Re|Flex system. This harness is designed to enhance your vehicle's performance by scaling the sequential port injection based on real-time ethanol content, eliminating the need for manual adjustments. Key benefits include:

Effortless Installation: Plug-n-play design makes it easy to connect an ethanol content sensor without extensive modifications.
Real-Time Adjustments: Allows for automatic scaling of port injection based on real-time ethanol content, optimizing engine performance.
Seamless Integration: For CANbus integrated vehicles, it facilitates integration with the factory DME/ECU (pending feature release by tuning platforms).
No Manual Flashes Required: Removes the need for ground disconnection or map switching on your port injection controller.

Please note that the ethanol sensor is not included with this harness.

Show More Show Less

Port Injector Plugs

T#:27171925

Part#: UNI-BMS-PIPLUGS

In Stock

$ 60.00 USD

Add to Wish List

Qty

$ 60.00 USD

Add to Wish List

These dummy injectors fit in place of port injection fuel injectors to block the holes. Allows use to aluminum manifolds with port injection bungs without having to purchase fuel injectors. Plugs are EV14 injectors and measure 38mm or 1.5" from o-ring to o-ring.

Show More Show Less

BMW B58 3.0L ReFlex+ Main Injector Harness - Inline-6

T#:29201081

Part#: 900.1008

In Stock

$ 200.00 USD

Add to Wish List

Qty

$ 200.00 USD

Add to Wish List

BMW B58 3.0L ReFlex+ Main Injector Harness - Inline-6 offers a seamless integration solution for your turbocharged BMW inline-6 engine. Designed to work with the Motive ReFlex Control Unit, this plug-n-play harness ensures a hassle-free installation process for your 6 EV6/USCAR injectors.

Direct Plug-N-Play Installation: Connects directly to the ReFlex+ Control Unit and your EV6/USCAR injectors.
Versatile Connector Options: Includes DTM 3-Pin and 2-Pin connectors for integration with ethanol content sensors and external sensors.
Multiple Sensor Connectors: Features connections for a 0-10 Bar Pressure Sensor and a 0-5v sensor.
Auxiliary Output Wires: Provides 3x unterminated wires for additional low-side triggers from the ReFlex+ Control Unit.
Easy Connection: DTM 8-Pin connector allows for straightforward setup with ReFlex+ Install Harnesses.

Turner Motorsport's harness ensures efficient and reliable performance, streamlining the process of integrating your ReFlex+ Control Unit with your BMW B58 engine.

Show More Show Less

3/8" Quick Disconnect Adapter With 1/8" NPT Port

T#:29500156

Part#: 200.1105

In Stock

$ 24.00 USD

Add to Wish List

Qty

$ 24.00 USD

Add to Wish List

Quick disconnect adapters (QDA) are commonly used to adapt different components into vehicle fuel systems without requiring permanent modification. These adaptersÂ are machined from high-grade aluminum and anodized for corrosion resistance. QDAs incorporate VitonÂ© o-rings which are compatible with most types of fuel, solvents and oils. QDAs maintain a reliable leak-proof seal under normal fuel injection system operating pressures. This particular QDA is sized perfectly to adapt right between the fuel line you were going to connect to your ethanol sensor. 3/8" (9.5mm) female quick disconnect 3/8" (9.5mm) male quick disconnect 1/8" Female pipe thread port * Viton© o-rings Crecent-lock system E-85 compatible Black anodized aluminum

Show More Show Less

BMW N54 Port Injection Intake Manifold With 750cc Injectors And Fuel ...

T#:21933055

Part#: N54PIIMINJECT

Back Ordered

$ 988.00 USD

Add to Wish List

Qty

$ 988.00 USD

Add to Wish List

BMW N54 Port Injection Intake Manifold With 750cc Injectors And Fuel Line Kit - Phoenix Racing is a high-performance upgrade engineered to replace the stock plastic intake manifold on BMW N54 engines. Constructed from durable, lightweight aluminum, this manifold increases airflow and strength, delivering reliable performance for both street and track applications. Integrated with top-mount port injection bungs, this manifold ensures optimal fuel delivery and spray patterns for maximum efficiency. The Phoenix Racing kit includes calibrated 750cc injectors and a plug-and-play fuel line, making it ideal for drivers aiming for high horsepower and seamless installation. Available through Turner Motorsport.

Replaces the factory plastic manifold with high-strength aluminum for increased durability and performance
Supports increased airflow to enhance engine power and efficiency
Integrated top-mount port injection bungs optimize fuel injector spray and delivery
Includes calibrated 750cc injectors and plug-and-play fuel line for a complete port injection solution
Multiple expansion vacuum ports support blow-off valves, boost gauges, Hobb’s switches, and more
High-quality, high-temperature o-rings provide lasting durability and reliability
Exclusively available through Turner Motorsport, ensuring trusted quality and service

Show More Show Less

VTT N54 Vacuum Pump Block Off Plate

2X Entries Into Our F80 M3 Sweepstakes

T#:11497328

Part#: VTT-N54-VACUUM-B

Ships in 9 Business Days

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

Looking to remove the HPFP or DI system on your N54? this plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes Block Plate Note – Plates may come in a clear or anodize black finish depending on stock on hand

Show More Show Less

VTT BMW N54 “DI Injector” Delete Kit

2X Entries Into Our F80 M3 Sweepstakes

T#:11497326

Part#: VTT-N54-DI-DELET

Ships in 1-2 days

$ 339.99 USD

Add to Wish List

Qty

$ 339.99 USD

Add to Wish List

Looking to get rid of the troublesome and expensive DI injectors on your BMW N54 and move to PI only and a standalone? If so VTT has you covered with its new N54 PI delete kit. This kit allows you to SAFELY remove the DI injectors, install our delete fittings, and run PI only. We machined these deletes from 310 Stainless for extreme heat, and corrosion resistance, and include 3 hold downs. These DI deletes COMPLETELY get rid of all factory provisions, including the seal. If the seal is left intact with no fuel to cool the injector or delete it will quickly overheat and melt the delicate seal causing combustion gasses to escape the engine creating misfires, and worse possibly damaging your injector bore on the cylinder head. Our deletes are machined to be a press fit into the cylinder, and can be either cooled with liquid nitrogen, and dropped in, or tapped in with a hammer, and then held down with the included hold downs. We also include M6 tapped holes on the top of each one in case they need to be removed you can attach a slide hammer, and remove the delete. These are sold as a kit and come with the following 6 – 310 Stainless DI Delete fittings 3 – Hold down brackets Completetion of this kit will require the purchase of HPFP delete plate - ES# 4623950 PLEASE NOTE: THIS KIT REQUIRES EXTENSIVE MODIFICATIONS TO CONVERT YOUR ENGINE TO PI ONLY. THIS INCLUDES BUT IS NOT LIMITED TO A FULL PORT INJECTION SOLUTION, AND STAND-ALONE TO RUN THE PI SYSTEM. WE RECOMMEND THIS PNP SYSTEM USING THE MAXX ECU IT PROVIDES ALL YOU NEED TO GET UP AND RUNNING WITH PI ONLY ON THE TUNING SIDE OF THINGS – https://www.pnpecu.com/pnpecu-maxxecu-n54-pnp-kit-437-p.asp

Show More Show Less

ReFlex+ Install Harness - Flying Lead

T#:29201083

Part#: 900.1016

In Stock

$ 95.00 USD

Add to Wish List

Qty

$ 95.00 USD

Add to Wish List

A flying lead harness is a wiring harness that is unterminated at one end and has an excess length of wire so that installation can be customized by the end user. That makes this section of the ReFlex+ Install Harness truly universal. On one end, this harness has an 8-pin connector to plug into any one of our ReFlex+ Main Injector Harnesses. The other end of each wire is unterminated and will be connected to the appropriate sensor, ground, or power supply based on installation instructions. Each harness has a wire for: Switched +12v Input w/ inline fuse +5v Input Ground Can HI Can Lo Cam Sensor Signal Crank Sensor Signal Map Sensor Signal

Show More Show Less

Multi-Pump Fuel Surge Tank (MPFST)

T#:31059457

Part#: 20-1440

In Stock at Vendor

$ 549.99 USD

Add to Wish List

Qty

$ 549.99 USD

Add to Wish List

BMW Fuel Line Upgrade - Short Line Kit

T#:29267521

Part#: 900.1025

In Stock

$ 150.00 USD

Add to Wish List

Qty

$ 150.00 USD

Add to Wish List

Factory fuel lines are often not designed or safe for use with ethanol based fuels. Our PTFE fuel lines are the perfect solution for installing into your vehicle without having to permanently modify your vehicle's fuel lines. Simply uninstall the factory line and install our pre-measured lines that come setup with the correct fittings for a plug-n-play install in your vehicle. Please Note: This does NOT include an ethanol Content Sensor.

Show More Show Less

Radium Engineering Fuel Surge Tank Kit - E9X Non M

T#:577879

Part#: 20-0470

Back Ordered

Starting at $ 599.99 USD

Add to Wish List

Starting at $ 599.99 USD

Add to Wish List

Designed to prevent fuel starvation by acting as a reserve tank to keep fuel flowing in the case of the main tank sump running dry, during hard acceleration or turning for example. The BMW fuel surge tank install kit includes all needed brackets and hoses for a complete installation. This surge tank kit installs in place of the factory filter and fuel pressure regulator located in the fuel tank for a easy installation, the factory fuel pump is still in place and acts in tandem with the surge tank pumps by maintaining fuel level in the surge tank.

Show More Show Less

E-Chassis Stage 3 Bucketless LPFP Upgrade - N54/55

T#:38890918

Part#: BMSS3BLPFPN5455

Ships on Oct 23, 2026

$ 399.99 USD

Add to Wish List

Qty

$ 399.99 USD

Add to Wish List

If you're already using our Stage 2 Bucketless LPFP and want to upgrade to Stage 3, this kit is for you. If you don’t have the Stage 2 kit, you can purchase it here. Note: Stage 3 requires the Stage 2 bucketless kit. The Stage 3 upgrade kit includes: - Complete plug-and-play solution with the addition of the secondary module - Custom billet aluminum fitting to run both pumps in parallel - Wiring harness for the secondary pump - Spare vent tube clip - New Walbro filter - New E85-compatible Walbro 450 pump (F90000274) - Optional upgrade to Walbro 525 pump (F90000285) Recommended accessories: - Lock Ring Removal Tool - Hobb's switch

Show More Show Less

Radium - Split-Flow Flex Fuel Sensor Adapter

T#:53290958

Part#: 20-0589

In Stock at Vendor

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

Vargas Shotgun Single Barrel - MT - BMW E9X, E8X N54

For vehicles with Manual Transmission only

2X Entries Into Our F80 M3 Sweepstakes

T#:52305464

Part#: STGN-SB-1-N54-MT

Ships on Oct 22, 2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

The VTT Single Barrel for Manual Transmissions is the "Stage 1" of the Shotgun family, providing a massive headroom increase over the stock setup.

N55 Port Injection Kit With Intake Manifold, 950cc Injectors & Fuel L...

T#:42133542

Part#: BMW-N55-PRM-950

Back Ordered

$ 1,138.00 USD

Add to Wish List

Qty

$ 1,138.00 USD

Add to Wish List

Phoenix Racing N54 Port Injection Intake Manifold With 750cc Injector...

T#:44258354

Part#: BMW-N54PORT-750

Back Ordered

$ 988.00 USD

Add to Wish List

Qty

$ 988.00 USD

Add to Wish List

BMW N54 Port Injection Intake Manifold With 750cc Injectors And Fuel Line Kit - Phoenix Racing is a high-performance upgrade engineered to replace the stock plastic intake manifold on BMW N54 engines. Constructed from durable, lightweight aluminum, this manifold increases airflow and strength, delivering reliable performance for both street and track applications. Integrated with top-mount port injection bungs, this manifold ensures optimal fuel delivery and spray patterns for maximum efficiency. The Phoenix Racing kit includes calibrated 750cc injectors and a plug-and-play fuel line, making it ideal for drivers aiming for high horsepower and seamless installation. Available through Turner Motorsport.

Replaces the factory plastic manifold with high-strength aluminum for increased durability and performance
Supports increased airflow to enhance engine power and efficiency
Integrated top-mount port injection bungs optimize fuel injector spray and delivery
Includes calibrated 750cc injectors and plug-and-play fuel line for a complete port injection solution
Multiple expansion vacuum ports support blow-off valves, boost gauges, Hobb’s switches, and more
High-quality, high-temperature o-rings provide lasting durability and reliability
Exclusively available through Turner Motorsport, ensuring trusted quality and service

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Fuel System Parts for BMW 3 Series E93 (2007-2013)

Sub-Categories

BMW B46 B48 B58 Motiv ReFlex 0-10 Bar Pressure Sensor

BMW B46 B48 Motiv ReFlex Plug-n-Play Ethanol Sensor Harness

Port Injector Plugs

BMW B58 3.0L ReFlex+ Main Injector Harness - Inline-6

3/8" Quick Disconnect Adapter With 1/8" NPT Port

BMW N54 Port Injection Intake Manifold With 750cc Injectors And Fuel ...

VTT N54 Vacuum Pump Block Off Plate

VTT BMW N54 “DI Injector” Delete Kit

ReFlex+ Install Harness - Flying Lead

Multi-Pump Fuel Surge Tank (MPFST)

BMW Fuel Line Upgrade - Short Line Kit

Radium Engineering Fuel Surge Tank Kit - E9X Non M

E-Chassis Stage 3 Bucketless LPFP Upgrade - N54/55

Radium - Split-Flow Flex Fuel Sensor Adapter

Vargas Shotgun Single Barrel - MT - BMW E9X, E8X N54

N55 Port Injection Kit With Intake Manifold, 950cc Injectors & Fuel L...

Phoenix Racing N54 Port Injection Intake Manifold With 750cc Injector...

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results