Select Vehicle
BMW
Mini
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
The intake boot is a regular issue especially for BMW's, nearly all vehicles have a boot manufactured from rubber with an accordion section in the design for flexibility. This flexible section is typically where the failure comes from, leading to vacuum leak engine codes, rough idle, and increase fuel consumption.
When you upgrade to a Turner silicone intake boot you get a perfect fit that will not only outlast the OE design (meaning any vacuum leaks and rough idle), while also smoothing out airflow within the intake tract. This boot also eliminates the factory intake resonator giving your engine a much more aggressive sound under the hood especially at higher rpm. Available in black or Turner blue color, our intake boot offers either a pop of color or a cohesive, complementary look in your engine bay.
The Turner Motorsport silicone intake boot is manufactured with 5 layers of wire reinforced silicone to prevent collapse under load. Engineered in-house utilizing 3D scanning technology, this boot offers perfect fitment with the factory air box and either single stage or three stage (high output N52) intake manifolds.
Install as a standalone reliability improvement or in addition to our three stage intake manifold and Turner performance tune (available here).
Replaces OE intake boot 13717536004.
Features:
This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i Coupe Convertible
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi - Coupe
2007-2013 E93 BMW 328i - Convertible
The intake boot is a regular issue especially for BMW's, nearly all vehicles have a boot manufactured from rubber with an accordion section in the design for flexibility. This flexible section is typically where the failure comes from leading to vacuum leak engine codes, rough idle, and increase fuel consumption.
When you upgrade to a Turner silicone intake boot you get a perfect fit that will not only outlast the OE design (meaning any vacuum leaks and rough idle), while also smoothing out airflow within the intake tract. This boot also eliminates the factory intake resonator giving your engine a much more aggressive sound under the hood especially at higher rpm. Available in black or Turner blue color, our intake boot offers either a pop of color or a cohesive, complementary look in your engine bay.
The Turner Motorsport silicone intake boot is manufactured with 5 layers of wire reinforced silicone to prevent collapse under load. Engineered in-house utilizing 3D scanning technology, this boot offers perfect fitment with the factory air box and either single stage or three stage (high output N52) intake manifolds.
Install as a standalone reliability improvement or in addition to our three stage intake manifold and Turner performance tune (available here).
Replaces OE intake boot 13717536004.
Features:
This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i Coupe Convertible
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi - Coupe
2007-2013 E93 BMW 328i - Convertible
At Turner, all our Carbon Fiber Intake Systems are top-of-the-line custom-engineered products that we develop in house. Our S65 Intake is no exception. Turner Carbon Fiber Intakes start with a 3D scan of the factory intake and engine bay. Our engineers use these 3D images of the chassis to design the intake in SolidWorks modeling software. Using a Flow Bench, our Intake is then airflow tested against the factory intake, to ensure optimal airflow improvement against stock. The final product is a beautiful and functional Carbon Fiber Intake, CAD designed for perfect integration with the OEM inlet ducting and stock mounting locations and proven to flow better than factory.
Our Turner S65 Carbon Intake is a monster that perfectly compliments the high revving 4.0l V8 engine. The intake benefits start right at the motor; directly connected to the plenum is a full carbon intake tube with a substantially larger cross sectional area with smooth transitions which results in more airflow available to the engine in high demand scenarios. The inlet tube mounts securely to the full carbon heat shield and is mounted in factory airbox locations while retaining the factory cold air induction tract from the hood. Housed inside the heat shield is a behemoth cone filter to ensure proper filtration and maximize airflow. Turner's S65 intake is designed with air flow in mind and features a roaring induction sound. This intake flows like no other, during testing our intake outperformed the flowbench at over 750CFM, a massive improvement over the factory intake.
Benefits:
There is no other intake on the market like our S65 intake which will make your car unique and stand out from the rest of the E9x M3's.
You get a beautiful carbon design with one of the only full carbon fiber heatshields available.
All the flow - the air on demand will make sure your engine always has room to breathe.
Increased throttle response.
Added induction noise for an intoxicating driving experience.
PART DESIGN:
Designed and engineered in-house using state of the art 3D laser scanning and CAD technology for precision fitment
Hood Inlet Scoop - Directs the flow of cool, ambient air to the heat shield, and directly into the air filter. Seals off with the factory rubber gasket on the lower side of the hood inlet.
Full Carbon Fiber Heat Shield Assembly that utilizes OEM air box mounts and integrates with the factory air intake tract from the hood.
Monstrous 9" cone air filter to maximizes filtration that is able to be serviced/cleaned.
7"x5" Carbon Fiber Inlet Tube providing smooth, direct airflow from the behemoth air filter directly into the plenum.
Fully compatible with the OEM Secondary Air Injection emissions system. Factory hose lock and location.
KIT CONTENTS
Carbon Fiber Heat Shield
Carbon Fiber Intake Tube
Plenum Silicone Coupler
9" Cone Air Filter
Installation Hardware
PRODUCT DEVELOPMENT
Turner S65 Intake System was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing. Performance data metrics are collected utilizing Mustang AWD 500 SE in ground dyno and in-house Superflow SF-750 Flowbench.
Over 13 CFM more airflow than factory intake plenum! Beautiful Carbon Fiber construction with a roaring induction sound!
At Turner Motorsport, all our Carbon Fiber Intake Systems are top-of-the-line custom-engineered products that we developed in house. Our engineers took it upon themselves to design a prettier, cost effective Carbon Fiber Intake Plenum for S65 owners to compliment our E9x Carbon Fiber Intake System while retaining OEM features. Our S65 Carbon Intake Plenum is no different. Our Carbon Fiber Intakes start with a 3D scan of the factory intake and engine bay. Our Engineers use these 3D images of the chassis to design the intake plenum in SolidWorks modeling software. Using a Flow Bench, the Intake Plenum is then airflow tested against the factory intake, to ensure optimal airflow improvement against stock. The final product is a beautiful and functional Carbon Fiber Intake Plenum, CAD designed for perfect integration with the OEM inlet ducting and stock mounting locations. Our Carbon fiber Intake trumpets flow an average of 13 CFM over the stock BMW intake.
Our E9X M3 S65 Carbon Fiber Intake Plenum is made from 100% high grade prepreg 2x2 twill weave carbon including the internal trumpets, this plenum replaces the OEM plastic plenum allowing the naturally aspirated BMW V8 engine to generate more inductions sounds taking the driving experience of the M3 to a whole new level. The raw V8 rumble gives the M3 an almost CSL like sound and is truly an intoxicating experience. We went through several iterations using different carbon thicknesses to fine tune the sound and the resulting plenum generates an almost unbelievable induction volume and tone.
Our Carbon Fiber Intake Plenum can be used with the OEM airbox or any aftermarket intake system. Paired with our E9X M3 intake system, you're sure to upgrade the look and sound of your S65 engine.
Design Features and Benefits:
CAD designed Intake System for perfect integration with the OEM connections and stock mounting locations.
Carbon intake is manufactured using 2X2 twill weave carbon fiber for a great look in the engine bay.
Plenum is protected by a gloss finish clear coat for UV protection.
Uses OE intake temp sensor and hose locations
Provides same fitment as OE intake
Performance:
Carbon fiber Intake trumpets flow an average of 13 CFM over the stock BMW intake.
\
Full carbon fiber intake to increase flow, performance and aesthetics! Dual inlet design for maximized air flow while retaining the OEM+ fitment.
The most common N55 intake utilizes a short plastic tube and oversized cone filter; it is your job to have better taste than the common N55 owner. This carbon intake changes the whole image of the N55 engine while maintaining a flow of cool air and added induction noise. With a dual inlet design the engine bay retains its functionality while adding a second inlet to provide your engine with improved air flow and sound. To ensure the engine gets the coolest air possible the second inlet is located in the "sweet spot" on the cold side of the engine for the lowest intake air temps and most air flow possible. The cone filter features a bellmouth velocity stack filter that creates the satisfying flutter after letting of the throttle.
Our Turner Carbon Fiber Intakes start with a 3D scan of the factory intake and engine bay. Engineers use the 3D imaging of the chassis to design the intake in SolidWorks modeling software. Using a Flow Bench, the Intake is then airflow tested against the factory intake, to ensure optimal airflow improvement against stock. The final product is a beautiful and functional Carbon Fiber Intake, CAD designed for perfect integration with the OEM inlet ducting and stock mounting locations and proven to flow better than factory.
Key Benefits:
Increased flow over the factory intake
Carbon fiber airbox and intake tube with gloss clear coat for UV protection
CAD-Designed for perfect Integration
Custom high flow air filter specially designed to to pair with the carbon fiber airbox
Kit Contents:
Carbon Intake Tube
Full Carbon 2 Piece Airbox
Bellmouth Velocity Stack Cone Filter
Billet Turbo Inlet Adapter
Silicone Coupler
Hardware For Installation
Design:
- Carbon Fiber Intake Tube
Carbon inlet tube featuring a smoother interior without corrugations for a smooth flow path.
Integrated carbon flange allows secure mounting of the tube to the carbon air boxes.
Intake tube is manufactured using 2x2 twill weave carbon fiber for a great look in the engine bay.
Gloss finish clear coat for UV protection.
4-ply reinforced silicone coupler and 6061-T6 black anodized aluminum flange that utilizes the factory o-ring and retaining clip.
- Air Box
Carbon fiber airboxes are manufactured using 2X2 twill weave carbon fiber and protected with a gloss finish clear coat for UV resistance to match the intake tube.
Air box mounts in stock location with supplied hardware.
- Air Filter
Conical hi-flow reusable air filter; featuring 8 ply oiled cotton gauze construction to maximize filtration efficiency.
Bellmouth (velocity stack) filter flange inlet to reduce turbulence in order to maximize flow.
Product Development:
Turner N55 Intake System was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing. Performance data metrics are collected utilizing Mustang AWD 500 SE in ground dyno and in-house Superflow SF-750 Flowbench.
Fitment:
E82 135i N55
E88 135i N55
E84 X1 35i
E90 335/xi N55
E92 335/xi N55
E93 335/xi N55
At Turner, all our Carbon Fiber Intake Systems are top-of-the-line custom-engineered products that we develop in house. Our Turner S65 Carbon Intake is a monster that perfectly compliments the high revving 4.0l V8 engine. Add in a full carbon plenum and you have a recipe for greatness! The intake benefits start right at the motor; the plenum offers a larger interior volume and full carbon design which helps boast the intoxicating roar. Directly connected to the plenum is a full carbon intake tube with a substantially larger cross sectional area with smooth transitions which results in more airflow available to the engine in high demand scenarios. The inlet tube mounts securely to the full carbon heat shield and is mounted in factory airbox locations while retaining the factory cold air induction tract from the hood. Housed inside the heat shield is a behemoth cone filter to ensure proper filtration and maximize airflow. Turner's S65 intake and plenum is designed with air flow and induction in mind. The intake flows like no other; during testing, the Turner intake outperformed the flow-bench at over 750CFM, a massive improvement over the factory intake.
Here are the benefits:
Full carbon plenum and intake for a full engine bay transformation
You get a beautiful carbon heatshield, one of the only full carbon fiber heatshields available.
All the flow - the air on demand will make sure your engine always has room to breathe.
Increased throttle response.
Added induction noise for an intoxicating driving experience.
PART DESIGN:
Designed and engineered in-house using state of the art 3D laser scanning and CAD technology for precision fitment
Full Carbon Plenum construction with internal bracing and velocity stacks
Hood Inlet Scoop - Directs the flow of cool, ambient air to the heat shield, and directly into the air filter. Seals off with the factory rubber gasket on the lower side of the hood inlet.
Full Carbon Fiber Heat Shield Assembly that utilizes OEM air box mounts and integrates with the factory air intake tract from the hood.
Monstrous 9" cone air filter to maximizes filtration that is able to be serviced/cleaned.
7"x5" Carbon Fiber Inlet Tube providing smooth, direct airflow from the behemoth air filter directly into the plenum.
Fully compatible with the OEM Secondary Air Injection emissions system. Factory hose lock and location.
Full carbon fiber plenum with bracing and carbon velocity stacks.
KIT CONTENTS
Carbon Fiber Plenum
Carbon Fiber Heat Shield
Carbon Fiber Intake Tube
Plenum Silicone Coupler
9" Cone Air Filter
Installation Hardware
PRODUCT DEVELOPMENT
Turner S65 Intake System was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing. Performance data metrics are collected utilizing Mustang AWD 500 SE in ground dyno and in-house Superflow SF-750 Flowbench.
Unlock the full potential of your turbocharged N54 or N55 engine with the Turner Motorsport Stepped Intercooler. Whether you're running higher boost, track days, or just spirited street driving, this direct-fit upgrade is engineered to dramatically reduce intake air temperatures (IATs) and improve charge air flow for consistent, reliable performance.
Cooler air is denser air, and that means more oxygen per cycle for better combustion and more power. The factory intercooler quickly becomes a bottleneck under increased load or in warm conditions. Turner’s stepped intercooler solves that by offering an 80% increase in frontal surface area and cross-sectional flow, helping your BMW stay cooler and pull harder.
Constructed with high-quality cast aluminum end tanks and a bar-and-plate core, this intercooler delivers superior cooling efficiency and reduced pressure drop, even under sustained high-boost operation. The black powder-coated finish offers a clean, stealthy appearance, while the etched Turner logos add just the right touch of motorsport style.
Perfect for:
E82/E88 135i, E9X 335i/335xi, E84 X135i, E89 Z4 35i/35is
Key Features:
Direct-fit upgrade for E chassis N54 & N55 engines
Durable cast aluminum end tanks
High-efficiency bar-and-plate design
80% increase in frontal and cross-sectional area vs. stock
90% increase in charge air volume
Substantially lower IATs for improved power and reliability
Reduced and more consistent pressure drop
Lightweight design (under 20 lbs)
Dimensions: 520mm wide × 210mm tall × 130mm deep
Stealth black finish with Turner-etched logos
If you're looking to push your turbo BMW harder, the Turner Motorsport Stepped Intercooler is the cooling solution that keeps your engine running strong—pull after pull.