ECS for BMW 3 Series E93 (2007-2013)

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 215mm (8.46") to 275mm (10.82") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints(M12x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability

The factory plastic gears in BMW S65 and S85 throttle body actuators are notorious for premature wear due to mechanical stress, engine vibration, and heat cycling. Over time, this wear leads to excessive play, throttle response issues, and eventual failure. This can cause DME fault codes, limp mode, and DSC malfunctions. While replacing both throttle actuators is costly, even new OEM units will eventually suffer the same fate.

Thankfully, ECS has developed the ultimate solution for E9X M3, E60 M5, and E63/64 M6 owners! These Upgraded Throttle Body Actuator Gears are constructed of Teflon-reinforced nylon, significantly reducing friction and gear tooth wear for long-term reliability. Each gear comes pre-installed on a 4140 steel shaft, strengthening the assembly and ensuring a hassle-free installation. With this cost-effective and durable fix, you can eliminate throttle actuator failures for good!

Features & Benefits:

Upgraded Teflon-reinforced nylon gears – Superior to factory plastic-on-plastic gears, reducing wear and extending lifespan. Pre-installed 4140 steel shafts – Increases durability and simplifies installation. Prevents common actuator failures – Resolves worn gear issues that cause CELs, limp mode, and DSC/DME errors. Cost-effective alternative to full actuator replacement – Saves hundreds in parts and labor. Factory-like fitment – Engineered for precise compatibility and long-term reliability. Built to withstand heat and mechanical stress – Ensures consistent throttle performance and extended service life.

Tired of dealing with brittle, dry-rotted rubber hoses? Whether you're refreshing your cooling system or replacing aging components, this ECS Silicone Radiator Coolant Hose Set is the ultimate upgrade. Designed for durability, performance, and a factory-perfect fit, these premium silicone hoses outperform standard rubber in every way.

Why Choose Silicone Over Rubber?

Made from heavy-duty, reinforced 4-ply fluorosilicone, ECS hoses withstand extreme temperatures and pressures far beyond OEM rubber hoses. Engineered to resist oil, fuel, and electrochemical degradation, these hoses are tested for continuous operation at 250°F and over 45 psi, delivering superior reliability, reduced turbulence, and improved coolant flow.

Key Benefits:

Direct OE Fitment – Perfectly molded to factory specifications for seamless installation. Enhanced Durability – Heat-resistant silicone prevents cracking, swelling, and deterioration over time. Superior Cooling Performance – Smoother internal passageways improve coolant flow and system efficiency. Pre-Installed Quick-Connect Fittings – Hassle-free installation with OEM-style connectors. Premium Hardware Included – Comes with German-style stainless steel worm-drive hose clamps for a secure fit. Kit Includes:

Upper Radiator Hose Lower Radiator Hose Pre-Installed Factory "Quick-Connect" Flanges (4) Stainless Steel Worm-Drive Hose Clamps (4) Replaces OEM Part Numbers: 17127531579 & 17127564478

ECS Tuning Steering Rack Spacers – A Simple Upgrade for More Angle

Whether you're just beginning your drift journey or looking to refine your current angle kit, ECS Tuning's Steering Rack Spacers offer a simple yet effective solution. Installation is straightforward—just remove the inner tie rods and place the spacers with the chamfered side facing the tie rod for an instant angle boost.

During the development of their ECS E90 drift build, the team at ECS Tuning was eager to hit the track and start testing. On the first day of driving, it quickly became apparent that two essential upgrades were needed: a welded differential (which led to the creation of their custom-fit differential plates – (T#:35121162) and increased steering angle. However, rather than jumping straight into a full-angle kit, ECS focused on incremental improvements to fine-tune the car’s handling.

ECS engineers, including a beginner drifter, carefully measured and tested different spacer sizes to optimize angle while maintaining proper thread engagement on the inner tie rod. After extensive testing, they determined that 5mm was the sweet spot—providing the extra angle needed while ensuring a strong and secure connection.

For those looking to enhance their drift setup without committing to an expensive angle kit, ECS Steering Rack Spacers offer an affordable and effective solution.

Key Benefits:

Gain approximately 5° of extra steering angle on an otherwise stock setup
Budget-friendly alternative to expensive angle kits
Simple, bolt-on installation—no major modifications required
Works as a standalone mod or can be paired with angle kits for even greater gains
Design & Materials:

Material: Mild Steel
Finish: Zinc Coated for durability
Size: 5mm spacers
Take your drifting to the next level—one small upgrade at a time with ECS Tuning’s Steering Rack Spacers!

Includes connector housing with terminals and seals. Commonly used for the engine oil pressure switch.

ECS Tuning replacement harness connectors include all necessary pins and wire seals for a complete harness repair. Whether you have a broken harness connector or need a complete wiring repair, we have the components you need.

Each connector includes an additional terminal in case one becomes lost or damaged during installation.

Suggested tools:

Suggested crimping pliers: T#387193
Wire De-pin tools:
12pc De-Pin Tool Set - T#386379
23pc De-Pin Tool Set - T#641943

Achieving precise exhaust fitment can be tricky—especially when the exhaust hanger has room to slide. This movement can cause annoying rattles or even lead to contact with the underbody or rear bumper. The ECS Tuning Exhaust Locking Collar offers a simple and effective fix. Designed to clamp securely around the exhaust hanger, this collar keeps everything firmly in place, eliminating unwanted movement.

Crafted from high-strength 6031 billet aluminum and finished in a sleek black anodized coating, it delivers both durability and corrosion resistance. With this collar in place, your exhaust stays exactly where it should—no rattles, no surprises.

Product Design:

Made from precision machined 6061 aluminum Black anodized finish Stainless steel M5 X 0.8mm hardware Installation & Support:

Install the locking collar around your exhaust hanger, position the hanger in place, and snug the locking collar down in place against the hanger! ECS Exhaust Hanger Locking Collars are available for 10mm and 12mm exhaust hangers. Please measure your hangers before ordering. The 12mm locking collar can be found HERE.

Upgrade your BMW N55 engine with our Silicone Crank Case Vent Hose, a premium replacement for the fragile, failure-prone factory hose. Over time, the stock plastic hose deteriorates due to constant exposure to heat and oil, leading to cracks and leaks. Our solution? A high-quality silicone hose engineered for superior durability and long-term reliability.

To further enhance performance, we’ve lined the hose with fluorosilicone, providing exceptional resistance to oil and chemical degradation. Designed in-house using advanced CAD modeling and 3D scanning, this hose offers a precise OEM fit while eliminating the common weaknesses of plastic construction.

Each kit includes stainless steel hose clamps for a secure, hassle-free installation. Whether you’re replacing a worn-out CCV hose or upgrading for added peace of mind, this premium solution ensures your BMW N55 runs smoothly and efficiently for years to come.

Features:

Direct OEM Fit – Retains factory hose dimensions while eliminating reliability issues.
High-Performance Silicone – Resists heat-related wear for long-lasting durability.
4-Ply Fluorosilicone Lining – Superior protection against oil and chemical exposure.
Stainless Steel Clamps Included – Secure installation and extended service life.
Give your BMW N55 the reliability it deserves—upgrade to the Turner Motorsport Silicone CCV Hose today!

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 215mm (8.46") to 275mm (10.82") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints: Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability