BMW Tools & Specialty Equipment for BMW 6 Series F06 (2013+)

Due to clearance issues, many types of lifts require specific adapters that are made for reaching SUV and truck jack points. This 12-piece kit has been made by using stackable adapters that mount inside the lifting block trays so that vehicles with high ground-clearance or those with unique jack point locations are better accommodated. These adapters offer up to 7.2" of additional height when all combined.

Complete kit includes:

• Low‐profile round polyurethane contact pads  -  Qty: 4
• Sliding receivers that accommodate the round polyurethane contact pads and/or the stackable adapters  -  Qty: 4
• 3" stackable adapters.  -  Qty: 4

Fits BL-5000SLX/EXT and BL-7000SLX/EXT Series Only.

• Tough and rigid expanded polystyrene foam (EPS) with a load rating of 1,500lbs per wheel (almost twice what the normal corner weight would be on a 3-series BMW)
• 12" height X 12" width with minimal compression under load
• Light weight with each block weighing less than 6lbs and with a handy strap for carrying or hanging
• Curved cradle for the tire to sit inside
• Non-skid surface that won't scratch your floor

Looking for an alternative to your jack stands? With these wheel blocks you won't have to think twice about a jack stand scratching or denting the underside of your floor or the car falling off the jack stand. These work best when used with a floor jack under the subframe and the opposite axle wheels chocked. These are also a light weight and inexpensive alternative to the super-pricey plastic and metal ramps. They are resistant to most fluids and chemicals (but not solvents) and will never rust unlike metal ramps and blocks.

Also available in a 10" height.

Urethane Pinch-Weld Block - Set provides a superior solution for supporting vehicles on pinch-weld rails. Traditional rubber blocks can cause damage to delicate body rails due to excessive pressure points. These urethane pinch-weld blocks are engineered with a cross-cut slotted design, allowing versatile positioning either lengthwise or crosswise. They are ideal for safely supporting rocker panels or sheet metal body rails, particularly those that have degraded from corrosion over time.

• Specially formulated urethane rubber for durability
• Deep bilateral slots accommodate virtually all pinch weld frames
• Versatile positioning: lengthwise or crosswise
• Water, chemical resistant, and 100% weatherproof
• Single-piece construction ensures a superior hold
• Dimensions: 3.9” (L) x 2.9” (W) x 2.4” (H)

These QuickJack rubber contact blocks are used with all QuickJack systems and can be used with other QuickJack pads or are perfect to replace missing pads. If the blocks included with the QuickJack lift system have a hard time reaching the jack points of the vehicle, these can be used to help properly reach and support the vehicle on the lift.

These blocks are made of a hardened rubber that has specifically been formulated to resist gouging, cutting, and abrasion. They are also resilient against chemicals and solvents that would normally damage rubber.

Dimensions: 4" long x 2" tall x 3" wide

Engineered for optimal comfort and ease of movement, this reclining creeper seat is ideal for anyone working under vehicles. Its gas spring-supported backrest offers adjustable reclining from 0° to 70°, with seat angles shifting in 10° increments up to 30°, delivering superior ergonomics for mechanics and hobbyists alike.

Equipped with six 360° swivel casters, this creeper seat glides effortlessly around the workspace, allowing you to move smoothly without constantly adjusting your position, helping you stay focused on the job.

Constructed from heavy-duty materials, the seat is upholstered with non-slip, marine-grade vinyl, resistant to abrasion, chemicals, and oil. This durable design provides long-lasting comfort and is the perfect addition to your garage setup.

Features:

• TPR wheels feature a shock absorbing cushioned ride, while providing good floor protection and quiet rolling operation
• TPR wheels are resistant to chemicals, acids, alcohol, and water
• Wide, large diameter wheel improves rolling over rough surfaces
• Heavy-duty non-slip textured marine grade vinyl
• Comfortable thick-padded seat and backrest
• Locking casters
• Seat is resistant to abrasion, chemical, and oil

Specifications:

• Length (Backrest Up): 33 in. / 840 mm
• Length (Backrest Down): 45.25 in. / 1,150 mm
• Width (Frame): 17 in. / 430 mm
• Width Overall: 20.75 in. / 530 mm
• Seat Height (Down): 6.25 in. / 161 mm
• Backrest Height (Up): 31.5 in. / 800 mm
• Seat/Backrest Width: 14.75 in. / 376 mm
• Ground Clearance: ≈3 in. / 76 mm
• Seat Angle Min. / Max.: ≈0° to 30°
• Maximum Load: 600 lbs. / 272 kg.
• Backrest Angle Adjustment: Gas spring
• Seat Angle Adjustment: Mechanical Lock — 3 positions
• Casters: Six 360° Casters, ø2.5 in x .75 in., sleeve bearings, oil resistant, non-marring rubber wheels.
• Seat Materials: Padded Marine Vinyl Backrest and Seat. Marine Vinyl is abrasion, chemical and oil resistant.
• Frame Materials: Full powder coated, welded steel square tube
• Weight: 41.25 lbs. / 19 kg.
• Backrest Angle Min. / Max.: ≈0° to 70°