BMW Engine Parts for BMW 6 Series F06 (2013+)

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:​

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Elevate your custom installation with the ECS -10AN O-Ring Boss fitting, a crucial component that connects your ECS Tuning Catch Can to a 3/4" ID hose. This fitting simplifies your plumbing setup, ensuring a seamless solution.

Featuring a pre-installed Viton O-ring, this fitting is engineered for excellence, providing a leak-proof seal that resists the effects of oil and fuel exposure, guaranteeing long-term durability.

The 3/4" nipple is thoughtfully designed with barbs to secure hose position effectively, minimizing the risk of hose disconnection. Keep in mind that clamps and hoses are available for separate purchase. These fittings are sold individually, with most installations requiring a pair of them.

Featuring a T60 Torx head, the belt tensioner found on the N54/N55 engine has exceptionally tight quarters. Use of this tool will allow access to the lock pin hole without excessive component removal, making belt removal and installation a much easier task.

This tool fits all N54/N55 powered BMW, including: 
2008+ E82 BMW 135i 1M Coupe 
2014+ F22 BMW M235i 
2006+ E90 BMW 335i 335xi 335i xDrive - Sedan 
2007+ E92 BMW 335i 335is 335xi 335i xDrive - Coupe 
2007+ E93 BMW 335i - Convertible 
2012+ F30 BMW 335i 335i xDrive - Sedan 
2013+ F32 BMW 435i 435i xDrive - Coupe 
2014+ F34 BMW 335i xDrive GT - Gran Tourismo 
2015+ F80 BMW M3 - Sedan 
2015+ F82 BMW M4 - Coupe 
2015+ F83 BMW M4 - Convertible 
2006-2010 E60 BMW 535i 535xi 535i xDrive 
2010+ F07 BMW 535i GT, 535i xDrive GT 
2011+ F10 BMW 535i 535i xDrive 
2012+ F13 BMW 640i 
2009+ F01 BMW 740i 740li 
2011+ F25 BMW X3 xDrive35i 
2007-2013 E70 BMW X5 xDrive35i 
2007-2014 E71 BMW X6 xDrive35i 
2009+ Z4 BMW Z4 sDrive35i Z4 sDrive35is 

At almost half of the normal cost of Genuine BMW Installation Tool - No. 130190, this Schwaben BMW Fuel Injector O-Ring Tool Set is a perfect alternative to save money and ensure your have the proper tool for the job when it come time to service your fuel system. Make sure the job is done correctly the first time with this specialty item, relieving frustration and saving time all while preventing you from damaging critical seals or the injector itself that could otherwise be damaged if using the wrong tools for the job. 

This tool set includes all of the same components you would get with the BMW tool, the seal cutting pliers and seal installation components, made to exact specifications for perfect operation.

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Upgrade your stock oil cooler thermostat for improved performance. Swap out your existing cover with ease, replacing it with a durable billet cover. Upgrade from your 110-degree Celsius thermostat to a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly unlike thermostat bypass kits.

Kit contents:

Billet thermostat housing cover
Replacement gasket
Hardware
Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Looking to update your old torque wrenches? The Schwaben 3/8" Drive Digital Torque Wrench is your answer. 

This digital torque wrench uses an easy-to-read display to show torque amounts and settings, features a push button release, reversible 3/8" drive, 45 tooth ratchet head, and a comfortable no-slip grip and adjustment wheel.

Specifications:

• Setting Range: 45-220 ft lbs (60-300 Nm)
• Display Units: ft-lbs, N-m, Inch-lbs, cm-kg2, and m-kg
• Size: 22" (550mm) length for easy leverage
• Accuracy: +- 3%
• Include blow molded holding case
• Requires one 3V CR2030 battery (included)

Modern emission regulations require a closed PCV/Breather system for cleaner operation. However, inefficient oil particle capture can lead to excessive oil vapor ingestion, causing carbon buildup, reduced performance, and fuel economy. ECS Tuning's updated ECS Baffled Oil Catch Can, now with an easy-to-empty 1/4" drain fitting, is engineered to collect toxic blow-by gases, minimize carbon deposits, and reduce oil contamination within engine oil. Recirculating oil vapor ensures emissions compliance without venting to the atmosphere.

• Key Features:
• Highly Efficient Oil Separator: Strategically positioned 4 chamber baffle system maximizes oil/air separation and minimizes oil droplets in the intake tract.
• Integrated Dipstick: Knurled and black anodized oil dipstick simplifies oil volume inspection.
• Reservoir: Available in 6oz or 8oz capacity with a 1/4" NPT drain plug fitting.
• Serviceable: Easily removable baffle plates and drain plug for cleaning.
• Easy/Customizable Installation: Combine with the ECS Universal Bracket Kit for simplified installation and adjustable mounting locations.
• Leak-Free Fittings: Machined -10AN ORB (O-Ring Boss) fittings available for secure connections (fittings sold separately).