BMW Engine Parts for BMW 6 Series F06 (2013+)

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

2X Entries Into Our F80 M3 Sweepstakes

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

BMW B46 B48 B58 Motiv ReFlex 0-10 Bar Pressure Sensor

T#:28537533

Part#: 101-0216

In Stock

$ 105.00 USD

Add to Wish List

Qty

$ 105.00 USD

Add to Wish List

BMW B46 B48 B58 Motiv ReFlex 0-10 Bar Pressure Sensor is designed for accurate measurement of fluid and air pressure in high-performance applications. Ideal for monitoring a variety of pressures including fuel, boost, coolant, and oil, this sensor provides crucial data for optimizing vehicle performance.

Featuring a 2-Pin DTM connector, this sensor offers a direct plug-and-play connection to the ReFlex+ harness, ensuring a seamless integration with flash platforms via CANbus. Each ReFlex+ unit can support up to two of these sensors, allowing for comprehensive monitoring.

Versatile Measurement: Capable of measuring fuel pressure, boost, coolant, oil, and other fluids.
Easy Integration: 2-Pin DTM connector provides a direct plug-and-play connection.
Comprehensive Monitoring: Supports integration of up to two sensors per ReFlex+ unit.
High-Performance Design: Designed to handle high pressures and deliver accurate readings.

For optimal installation, consider using the 3/8 Female to 3/8 Male SAE Quick Disconnect Adapter with a 1/8" NPT port on an ethanol sensor or the 5/16 Female to 5/16 Male SAE Quick Disconnect Adapter with a 1/8" NPT port on a factory fuel line. Please note that the ethanol sensor is not included.

Show More Show Less

BMW Oil Cap Crankcase Breather - All BMW w/2 prong oil fill cap ...

2X Entries Into Our F80 M3 Sweepstakes

T#:558084

Part#: VTT-CRANK-BREATH

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Show More Show Less

Motiv ReFlex+ for BMW

T#:17970629

Part#: RFXF02UI6

In Stock

$ 859.00 USD

Add to Wish List

Qty

$ 859.00 USD

Add to Wish List

The MOTIV ReFlex+ is an Advanced I/O Integration module allowing a level of precise control of auxiliary components. In addition, the ReFlex can incorporate external data into the factory DME/ECU in parallel through optional CANbus integration. Utilizing the CANbus option, multiple digital and analog signals can be used by the DME/ECU for safety, data logging, or adaptive tuning features. It is unique in its ability to function as a separate standalone, as well as a parallel module in conjunction with the DME/ECU. The ReFlex provides the most accurate and precise supplementary sequential fuel injection with the ability to control other advanced features all in one place. It brings a new level of control, function, and versatility to tuning any modern-day vehicle. Preset crank and cam trigger for most modern-day BMW engines, as well as fully configurable triggers to be synched on any vehicle application. Configurable to operate on 4, 5, 6, and 8-cylinder engines. 3 Point MAP sensor calibration table makes it configurable for almost any MAP or TMAP sensor. Sequential Port Injection with the ability to sense individual injector failures on 4 to 8-cylinder engines. Built-in Ethanol Content Analyzer. The Re|Flex firmware and XDFs include ethanol compensation tables to scale properly for varying ethanol % based on real-time input from the sensor. 2x Additional Outputs. These outputs have 12x12 resolution tables for control in TunerPro R/T. These can be configured to run as on/off, digital, frequency (25hz), or PID. Boost Control WGDC Methanol Solenoid Control PWM (for use with valves such as the Aquamist FAV and the ProMeth Pulse Valve) Nitrous Solenoid Control PWM Auxiliary fuel pump relay trigger 2x Inputs Ethanol Content Sensor Fuel Pressure Sensor (0-10bar) Oil Pressure (0-10bar) Coolant Pressure (0-10bar) EGBP/EMAP (0-10bar) CANbus (not required) enabled communication for the transmission and receiving of digital signals for fully DME/ECU integrated control of external modifications. The CANbus communications also allow for data and errors to be transmitted to and from the vehicle's engine control computer in order to add safeguards and implement engine trips and fail safes. Logging via OBDII is still fully functional and is not affected at all by the communication with the Re|Flex. Some of the developments underway include: Error reporting to and from factory ECU for unparalleled safety Output WGDC by converting an EWG signal to a more conventional DC output for controlling standard 3port and 4port boost solenoids for use with external WG’s The ability to datalog non-factory parameters such as ethanol content, additional pressure sensor, PI IDC, and more! These features make the Re|Flex the most powerful and safest supplementary and auxiliary controller on the market. However, this is only the beginning. As flash platforms find the need for more accessories to control, the Re|Flex was designed to be updated easily by the end user in order to add functionality as it is developed.

Show More Show Less

BMW B46 B48 Motiv ReFlex Plug-n-Play Ethanol Sensor Harness

For Vehicles With Motiv ReFlex Unit Currently Installed Only

T#:22723690

Part#: 101-0212

In Stock

$ 49.00 USD

Add to Wish List

Qty

$ 49.00 USD

Add to Wish List

BMW B46 B48 Motiv ReFlex Plug-n-Play Ethanol Sensor Harness simplifies the integration of an ethanol content sensor into your BMW's Re|Flex system. This harness is designed to enhance your vehicle's performance by scaling the sequential port injection based on real-time ethanol content, eliminating the need for manual adjustments. Key benefits include:

Effortless Installation: Plug-n-play design makes it easy to connect an ethanol content sensor without extensive modifications.
Real-Time Adjustments: Allows for automatic scaling of port injection based on real-time ethanol content, optimizing engine performance.
Seamless Integration: For CANbus integrated vehicles, it facilitates integration with the factory DME/ECU (pending feature release by tuning platforms).
No Manual Flashes Required: Removes the need for ground disconnection or map switching on your port injection controller.

Please note that the ethanol sensor is not included with this harness.

Show More Show Less

-10AN ORB X 3/4" Hose Barb Fitting Assembly

10X Entries Into Our F80 M3 Sweepstakes

T#:584114

Part#: 003779ECS10

In Stock

Sale - Save 25% $ 39.99

This product was last offered at the strikethrough price on
06-13-2026

$ 29.99 USD

Add to Wish List

Qty

Sale - Save 25%

$ 39.99

This product was last offered at the strikethrough price on
06-13-2026

$ 29.99 USD

Add to Wish List

Elevate your custom installation with the ECS -10AN O-Ring Boss fitting, a crucial component that connects your ECS Tuning Catch Can to a 3/4" ID hose. This fitting simplifies your plumbing setup, ensuring a seamless solution.

Featuring a pre-installed Viton O-ring, this fitting is engineered for excellence, providing a leak-proof seal that resists the effects of oil and fuel exposure, guaranteeing long-term durability.

The 3/4" nipple is thoughtfully designed with barbs to secure hose position effectively, minimizing the risk of hose disconnection. Keep in mind that clamps and hoses are available for separate purchase. These fittings are sold individually, with most installations requiring a pair of them.

Show More Show Less

ECS Billet Aluminum Oil Filter Housing Cap - N20 N52 N54 N55 S55 S58 ...

10X Entries Into Our F80 M3 Sweepstakes

T#:363147

Part#: 003296ECS01

Ships in 6 Business Days

Sale - Save 25% $ 152.99

This product was last offered at the strikethrough price on
06-13-2026

$ 114.74 USD

Add to Wish List

Qty

Sale - Save 25%

$ 152.99

This product was last offered at the strikethrough price on
06-13-2026

$ 114.74 USD

Add to Wish List

BMW uses a lot of plastic in their engine components to save weight and money. Unfortunately, plastic is damaged easily and the factory oil filter cap needs a special tool to remove.

Bremi Ignition Coil

T#:340576

Part#: 12131712219

Ships in 2 Business Days

$ 28.78

This product was last offered at the strikethrough price on
04-09-2026

$ 25.43 USD

Add to Wish List

Qty

$ 25.43 USD

Add to Wish List

Get your engine back to peak performance with a new ignition coil.

Vargas N54/55 Billet Crank Seal Guard - BMW N54 N55 3.0L

2X Entries Into Our F80 M3 Sweepstakes

T#:638889

Part#: VTT-CRANKGUARD

In Stock

Starting at $ 89.99 USD

Add to Wish List

Starting at $ 89.99 USD

Add to Wish List

It is a well-known issue on the BMW N54/55 platforms that your serpentine belt can fail for various reasons. When this happens, there is a high chance of the belt getting sucked behind the front damper pulley and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure. Even if you do not lose the engine, it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT, even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Vargas' seal is different from those already on market in two major ways. Firstly, it is not offensively priced. Secondly, it is 100% billet with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long-term corrosion resistance. Crank Seal Guard includes: One VTT Billet N54/55 Crank Seal Guard Two extended 12.9 Grade bolts, and two stainless washers We highly recommend you install WITH a crank bolt capture at the same time, as you have to remove the damper anyway. Then you will get the benefit of helping eliminate the dreaded spun crank hub and the crank seal issue

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

2X Entries Into Our F80 M3 Sweepstakes

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

BMW B58 3.0L ReFlex+ Main Injector Harness - Inline-6

T#:29201081

Part#: 900.1008

In Stock

$ 200.00 USD

Add to Wish List

Qty

$ 200.00 USD

Add to Wish List

BMW B58 3.0L ReFlex+ Main Injector Harness - Inline-6 offers a seamless integration solution for your turbocharged BMW inline-6 engine. Designed to work with the Motive ReFlex Control Unit, this plug-n-play harness ensures a hassle-free installation process for your 6 EV6/USCAR injectors.

Direct Plug-N-Play Installation: Connects directly to the ReFlex+ Control Unit and your EV6/USCAR injectors.
Versatile Connector Options: Includes DTM 3-Pin and 2-Pin connectors for integration with ethanol content sensors and external sensors.
Multiple Sensor Connectors: Features connections for a 0-10 Bar Pressure Sensor and a 0-5v sensor.
Auxiliary Output Wires: Provides 3x unterminated wires for additional low-side triggers from the ReFlex+ Control Unit.
Easy Connection: DTM 8-Pin connector allows for straightforward setup with ReFlex+ Install Harnesses.

Turner Motorsport's harness ensures efficient and reliable performance, streamlining the process of integrating your ReFlex+ Control Unit with your BMW B58 engine.

Show More Show Less

ECS Tuning Performance Kevlar Reinforced Belt - N55 F Chassis ...

10X Entries Into Our F80 M3 Sweepstakes

T#:5858461

Part#: 8PK1390

In Stock

$ 52.99 USD

Add to Wish List

Qty

$ 52.99 USD

Add to Wish List

Replaces BMW # 11287628661 Kevlar-reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM style belts.

Show More Show Less

Turner Universal Baffled Oil Catch Can Mounting Bracket Kit - BMW & M...

10X Entries Into Our F80 M3 Sweepstakes

T#:383333

Part#: 003779ECS06KT

In Stock

Sale - Save 25% $ 95.99

This product was last offered at the strikethrough price on
06-13-2026

$ 71.99 USD

Add to Wish List

Qty

Sale - Save 25%

$ 95.99

This product was last offered at the strikethrough price on
06-13-2026

$ 71.99 USD

Add to Wish List

If you don't wish to fabricate intricate brackets to mount your ECS Baffled Oil Catch Can we have the solution. ECS's three-piece bracket kit includes two options for securing the catch can. Choose from either a flat parallel mounting plate or a bent 90° mounting plate to give you 360° rotation for an infinitely adjustable mounting location.

Show More Show Less

Motiv ReFlex+ Control Unit

T#:29101684

Part#: 900.1001

In Stock

$ 729.00 USD

Add to Wish List

Qty

$ 729.00 USD

Add to Wish List

The motive ReFlex+ Control Unit is an advanced I/O integration module that allows precise control of aftermarket components and sends data to the factory DME (ECU) via CANbus communication, expanding performance tuning capabilities. This control unit allows for precise control of fuel pumps, methanol injection kits, nitrous kits, boost controllers, relay triggers, port injection systems, flex fuel systems, and more. Supporting sequential port injection for up to eight injectors and real-time monitoring of injectors, this unit is a great choice for precise control of fuel delivery to your engine.

Show More Show Less

ECS Billet Aluminum Oil Filter Cap - Black Anodized - N63 S63 ...

10X Entries Into Our F80 M3 Sweepstakes

T#:641063

Part#: 006060LA01

In Stock

Sale - Save 25% $ 183.99

This product was last offered at the strikethrough price on
06-14-2026

$ 137.99 USD

Add to Wish List

Qty

Sale - Save 25%

$ 183.99

This product was last offered at the strikethrough price on
06-14-2026

$ 137.99 USD

Add to Wish List

BMW uses a lot of plastic in their engine components to save weight and money. Unfortunately, plastic is damaged easily and the factory oil filter cap needs a special tool to remove. This aluminum cap is much more sturdy and features a standard 19mm hex post on the top. 19mm is also the size of your engine oil drain plug, reducing the number of tools that you need to complete an oil change. This cap is designed to use the original o-ring seal so no special parts are required. You only have to remove the original 'filter cage' from the original cap and transfer it to the new aluminum cap. The satin black anodize blends in with the rest of your engine bay making this a smart and subtle upgrade.

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

ECS Tuning Low Temp Oil Thermostat - BMW N54 N55 3.0L (2008+ Models) ...

For vehicles with a stock oil cooler

10X Entries Into Our F80 M3 Sweepstakes
For 2008 and up models only

T#:6924321

Part#: 090743ECS09

In Stock

Sale - Save 25% $ 79.99

This product was last offered at the strikethrough price on
06-14-2026

$ 59.99 USD

Add to Wish List

Qty

Sale - Save 25%

$ 79.99

This product was last offered at the strikethrough price on
06-14-2026

$ 59.99 USD

Add to Wish List

Is your N54/N55 oil temp running too high? The most likely cause is a faulty OE oil thermostat. With this ECS Low Temp Oil Thermostat Kit, you can keep your engine happy with oil temps holding between 194F (90c) to 230F (110c). This is the perfect solution for both higher milage models and models that have been tuned or further upgraded with performance turbochargers, Kit includes: Oil Thermostat Bung Oil Thermostat Spring Oil Thermostat Shaft Assembly

Show More Show Less

3/8" Quick Disconnect Adapter With 1/8" NPT Port

T#:29500156

Part#: 200.1105

Ships in 4 Business Days

$ 24.00 USD

Add to Wish List

Qty

$ 24.00 USD

Add to Wish List

Quick disconnect adapters (QDA) are commonly used to adapt different components into vehicle fuel systems without requiring permanent modification. These adaptersÂ are machined from high-grade aluminum and anodized for corrosion resistance. QDAs incorporate VitonÂ© o-rings which are compatible with most types of fuel, solvents and oils. QDAs maintain a reliable leak-proof seal under normal fuel injection system operating pressures. This particular QDA is sized perfectly to adapt right between the fuel line you were going to connect to your ethanol sensor. 3/8" (9.5mm) female quick disconnect 3/8" (9.5mm) male quick disconnect 1/8" Female pipe thread port * Viton© o-rings Crecent-lock system E-85 compatible Black anodized aluminum

Show More Show Less

Motiv ReFlex Lite: Advanced Sequential Injector Controller - Inline-6...

T#:29234298

Part#: 910.1011

In Stock

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

The ReFlex LITE is a simple yet elegant fueling solution for direct injected vehicles that need to add more fuel by installing a port injection system to keep up with their modifications to the vehicle. Using the same precise form of sequential fuel injection as the ReFlex+, the ReFlex LITE brings a more affordable fuel controller without the additional features of the ReFlex+. Sequential port fuel injection for inline-6 engines Firmware and maps are available for multiple vehicles FREE on our website High resolution calibration tables 24x24 cell RPM vs MAP 0-48psi MAP pressure range 250RPM increments up to 8500RPM High resolution datalogging Fault detection status available to monitor in TunerPRO RT Compact in size Universal fitment Simple installation Please Note: The ReFlex LITE does NOT have the ability to analyze and transmit ethanol content to an ECU.

Show More Show Less

Innovate LC-2 Wideband O2 Controller Kit

T#:28836410

Part#: 38770

In Stock at Vendor

$ 212.99 USD

Add to Wish List

Qty

$ 212.99 USD

Add to Wish List

Features & Benefits:

Two configurable linear 0-5V analog outputs Ability to calibrate O2 sensors for maximum accuracy Includes LC-2 controller and Bosch wideband O2 sensor Comes with a program cable, manual, and a 10 ft. sensor cable Includes a 1-inch mild steel exhaust bung Innovate MTS serial in/out capability Integrated dual-color status LED (green/red) Patented DirectDigital™ wideband sensor control Positive lock connectors for all connections Real-time display data on screen or with the powerful LogWorks software Range:

AFR (Air-Fuel Ratio) range from 7.4:1 to 22.4:1 (0.5 to 1.5 lambda)

Show More Show Less

Vargas Ignition Coil Kit (Red) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309610

Part#: VTT-COIL-N5X-RED

Ships in 10 Business Days

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

Vargas Burnt Titanium Magnetic Oil Drain Plug - M12 X 1.5

2X Entries Into Our F80 M3 Sweepstakes

T#:51813315

Part#: VTT-TI-DRAIN

Ships in 1-3 days

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

The VTT Burnt Titanium Magnetic Oil Drain Plug is a critical upgrade for any performance enthusiast looking to maximize engine longevity.

Vargas Ignition Coil Kit (Blue) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309605

Part#: VTT-COIL-N5X-BLU

Ships in 8 Business Days

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

ReFlex+ Install Harness - Flying Lead

T#:29201083

Part#: 900.1016

In Stock

$ 95.00 USD

Add to Wish List

Qty

$ 95.00 USD

Add to Wish List

A flying lead harness is a wiring harness that is unterminated at one end and has an excess length of wire so that installation can be customized by the end user. That makes this section of the ReFlex+ Install Harness truly universal. On one end, this harness has an 8-pin connector to plug into any one of our ReFlex+ Main Injector Harnesses. The other end of each wire is unterminated and will be connected to the appropriate sensor, ground, or power supply based on installation instructions. Each harness has a wire for: Switched +12v Input w/ inline fuse +5v Input Ground Can HI Can Lo Cam Sensor Signal Crank Sensor Signal Map Sensor Signal

Show More Show Less

1/2-inch Drive 17mm VANOS Flush-Cut Socket

10X Entries Into Our F80 M3 Sweepstakes

T#:394201

Part#: 012016ECS02A

In Stock

$ 28.99 USD

Add to Wish List

Qty

$ 28.99 USD

Add to Wish List

VTT Ignition Coil Conversion Kit - S55/N55 To B58 - Multiple Color Op...

2X Entries Into Our F80 M3 Sweepstakes

T#:22196341

Part#: VTTS55CLCNV

Ships in 5 Business Days

Starting at $ 335.99 USD

Add to Wish List

Starting at $ 335.99 USD

Add to Wish List

VTT is proud to offer its very own Game Changer S55/N55 to B58 Coil conversion kit for the BMW S55/N55 platforms. The 55 series of engines has notoriously had ignition problems with the factory coils, while aftermarket upgrades do exist, they can be bulky. The solution is the BMW B58 ignition coils which are extremely robust and can support well over 1000WHP with no issues. This means a plug-and-play affordable solution that fits like stock, and looks AMAZING doing so! We designed our own 6061-T6 Billet bracket in a plethora of colors including matching shades for every S55/N55 Valve Cover. This means you can mix and match the color of the bracket with coil color, with VC color to truly tailor your engine bay to look exactly how you want it to! The kit comes with the following: 3 – Billet Aluminum Coil Brackets in the color of choice 6 – Plug and play VTT wiring harnesses 6 – Custom VTT stalks to convert the B58 coils to the S55/N55 head (We ensure proper spring length inside the boot for optimal spring-to-plug contact) *NOTE: Flash setting changes may be required when installing the conversion kit to ensure the proper function of the B58 coils with S55/N55 DME. This can be found in almost all flashing software settings such as MHD, Bm3, etc.* **NOTE: THESE BRACKETS FIT STOCK S55 VC, VTT S55 BILLET VC, and MOST N55 made after 2011. If you have an older N55 made before 01/2011. These may not fit. Purchase carefully as items that have been installed or attempted to cannot be returned.**

Show More Show Less

ECS Performance Silicone Turbo Charger Coolant Hose Kit - S63 ...

10X Entries Into Our F80 M3 Sweepstakes

T#:7355613

Part#: 008648LA01

In Stock

Sale - Save 25% $ 61.99

This product was last offered at the strikethrough price on
06-14-2026

$ 46.49 USD

Add to Wish List

Qty

Sale - Save 25%

$ 61.99

This product was last offered at the strikethrough price on
06-14-2026

$ 46.49 USD

Add to Wish List

Designed using durable silicone and billet aluminum to greatly outlast the OE rubber and plastic combination.

OMP Battery Cut Off Switch / Kill Switch

T#:1614

Part#: EA-462

Back Ordered

$ 65.00 USD

Add to Wish List

Qty

$ 65.00 USD

Add to Wish List

OMP Battery Cut Off Switch / Kill Switch, for use in racecars as an emergency "kill switch", to depower the electrical system in the event of a crash or other emergency. This cut off switch is FIA approved, has 6 poles and alternator protection, as well as a removable key.

Show More Show Less

Hella Hella Horn - High Tone

T#:592707

Part#: 2768551

Ships in 1 Business Day

$ 30.99 USD

Add to Wish List

Qty

$ 30.99 USD

Add to Wish List

Disc Type High-Tone, 12 V, 400 Hz with Bracket

ECS Magnetic Differential Oil Drain Plug - M18x1.5

10X Entries Into Our F80 M3 Sweepstakes

T#:2706140

Part#: 008664LA01

In Stock

Sale - Save 44% $ 40.99

This product was last offered at the strikethrough price on
05-03-2026

$ 22.99 USD

Add to Wish List

Qty

Sale - Save 44%

$ 40.99

This product was last offered at the strikethrough price on
05-03-2026

$ 22.99 USD

Add to Wish List

Turn your oil drain plug into an effective metal particle filter! This drain plug has a SUPER strong magnet built into it's tip, trapping iron and steel contaminants and safely removing them from circulation.

Show More Show Less

Hella Hella Horn - Low Tone

T#:590880

Part#: 2768082

Ships on Oct 7, 2026

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Disc Type Low-Tone, 12 V, 335 Hz with Bracket

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

1/2-inch Drive 18mm VANOS Flush-Cut Socket

10X Entries Into Our F80 M3 Sweepstakes

T#:394202

Part#: 012016ECS03A

In Stock

Sale - Save 16% $ 37.99

This product was last offered at the strikethrough price on
05-03-2026

$ 32.08 USD

Add to Wish List

Qty

Sale - Save 16%

$ 37.99

This product was last offered at the strikethrough price on
05-03-2026

$ 32.08 USD

Add to Wish List

1/2-inch Drive VANOS Flush-Cut 17mm & 18mm Sockets

10X Entries Into Our F80 M3 Sweepstakes

T#:398953

Part#: 012016ECS0KTKT

In Stock

Sale - Save 3% $ 67.99

This product was last offered at the strikethrough price on
06-14-2026

$ 65.94 USD

Add to Wish List

Qty

Sale - Save 3%

$ 67.99

This product was last offered at the strikethrough price on
06-14-2026

$ 65.94 USD

Add to Wish List

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Clear - BMW N52 N...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122266

Part#: VTTFILTERCAPCLR

Ships in 1 Business Day

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

Walker Oxygen Sensor - Downstream - F22 M235, F3X 335/435, F06/F12 64...

from 7/2013 production date

T#:31324163

Part#: 11787645875

Ships in 1 Business Day

$ 101.99

This product was last offered at the strikethrough price on
04-14-2026

$ 91.99 USD

Add to Wish List

Qty

$ 91.99 USD

Add to Wish List

The oxygen sensor is part of your BMW's emissions control system and feeds data to BMW engine management computer. The oxygen sensor is positioned in the exhaust pipe and can detect rich and lean mixtures. The goal of the oxygen sensor is to help the engine run as efficiently as possible and also to produce as few emissions as possible. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today.

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Blue - BMW N52 N5...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122267

Part#: VTTFILTERCAPBLUE

Ships in 10 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

ECS Tuning Performance Kevlar Reinforced Accessory Belt - BMW E70 E71...

10X Entries Into Our F80 M3 Sweepstakes

T#:21933046

Part#: 8PK1478

Ships on Nov 12, 2026

$ 66.99 USD

Add to Wish List

Qty

$ 66.99 USD

Add to Wish List

Replaces BMW # 11287628659 and 11287589365 ECS Tuning Performance Kevlar reinforced belts give you that extra piece of mind! Kevlar reinforced belts experience less elongation over time minimizing the amount of belt adjustment needed as well as offering a higher shock and impact resistance compared to OEM style belts. ECS Tuning Performance Kevlar reinforced belts have been put through a series of multiple tests such. Tensile strength Elongation Hardness Temperature and oil resistance per standard JASO E 109-94 Flex testing per SAE J2432.

Show More Show Less

ECS Tuning Baffled Oil Catch Can - 8oz

10X Entries Into Our F80 M3 Sweepstakes

T#:13496655

Part#: 003779ECS05-02

In Stock

Sale - Save 10% $ 238.99

This product was last offered at the strikethrough price on
06-14-2026

$ 215.09 USD

Add to Wish List

Qty

Sale - Save 10%

$ 238.99

This product was last offered at the strikethrough price on
06-14-2026

$ 215.09 USD

Add to Wish List

Upgrade Your BMW with ECS Baffled Oil Catch Can

Modern emission regulations require a closed PCV/Breather system for cleaner operation. However, inefficient oil particle capture can lead to excessive oil vapor ingestion, causing carbon buildup, reduced performance, and fuel economy. ECS Tuning's updated ECS Baffled Oil Catch Can, now with an easy-to-empty 1/4" drain fitting, is engineered to collect toxic blow-by gases, minimize carbon deposits, and reduce oil contamination within engine oil. Recirculating oil vapor ensures emissions compliance without venting to the atmosphere.

Key Features:
Highly Efficient Oil Separator: Strategically positioned 4 chamber baffle system maximizes oil/air separation and minimizes oil droplets in the intake tract.
Integrated Dipstick: Knurled and black anodized oil dipstick simplifies oil volume inspection.
Reservoir: Available in 6oz or 8oz capacity with a 1/4" NPT drain plug fitting.
Serviceable: Easily removable baffle plates and drain plug for cleaning.
Easy/Customizable Installation: Combine with the ECS Universal Bracket Kit for simplified installation and adjustable mounting locations.
Leak-Free Fittings: Machined -10AN ORB (O-Ring Boss) fittings available for secure connections (fittings sold separately).

Show More Show Less

ECS Tuning Baffled Oil Catch Can - 6oz

10X Entries Into Our F80 M3 Sweepstakes
For use with custom plumbing and ECS universal mounting bracket kit

T#:17140141

Part#: 003779ECS05-01

In Stock

Sale - Save 46% $ 233.99

This product was last offered at the strikethrough price on
05-03-2026

$ 126.78 USD

Add to Wish List

Qty

Sale - Save 46%

$ 233.99

This product was last offered at the strikethrough price on
05-03-2026

$ 126.78 USD

Add to Wish List

Meet modern emission regulations while preserving engine performance with the ECS Baffled Oil Catch Can. Designed for BMW and MINI vehicles, this system efficiently captures blow-by gases, preventing excessive oil vapor ingestion into the intake tract. The innovative 4-chamber baffle system maximizes oil/air separation, reducing carbon build-up and pollutants. Featuring a 1/4" drain fitting for easy maintenance, this catch can minimizes oil deposits, ensuring cleaner emissions and enhanced engine performance.

Key Benefits:

Efficient 4-chamber baffle system for maximum oil/air separation
Recirculated design reduces oil ingestion, promoting cleaner emissions
Durable 6061-T6 billet machined body with anodized black finish for longevity
Integrated dipstick and sealed reservoir for easy oil inspection and maintenance
Serviceable design with removable baffle plates for cleaning
Easy installation with customizable mounting options and leak-free fittings
Engineered and manufactured in the USA for superior performance and durability

Note: Not for sale or use in the state of California on any pollution-controlled vehicle as per the California Air Resources Board.

Show More Show Less

VTT N5X/S55/N2X Triple Billet Cap Kit - Red - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122280

Part#: TRIPLECAPRED1

In Stock

$ 209.99 USD

Add to Wish List

Qty

$ 209.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

BMW Fuel Line Upgrade - Short Line Kit

T#:29267521

Part#: 900.1025

In Stock

$ 150.00 USD

Add to Wish List

Qty

$ 150.00 USD

Add to Wish List

Factory fuel lines are often not designed or safe for use with ethanol based fuels. Our PTFE fuel lines are the perfect solution for installing into your vehicle without having to permanently modify your vehicle's fuel lines. Simply uninstall the factory line and install our pre-measured lines that come setup with the correct fittings for a plug-n-play install in your vehicle. Please Note: This does NOT include an ethanol Content Sensor.

Show More Show Less

VTT N5X/S55/N2X Triple Billet Cap Kit - Clear - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122281

Part#: TRIPLECAPCLR1

Ships in 10 Business Days

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Red - BMW N52 N54...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122265

Part#: VTTFILTERCAPRED

In Stock

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

MTX-D: Ethanol Content % And Fuel Temperature Gauge

T#:22558994

Part#: INN3904

In Stock at Vendor

14% off MSRP $ 313.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 269.00 USD

Add to Wish List

Qty

14% off MSRP

$ 313.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 269.00 USD

Add to Wish List

Introducing the Innovate Motorsports MTX Digital Series "Dual Function" Gauges – now available! These 2 1/16" (52mm) gauges come with interchangeable faceplates and bezels, locking connectors for simplified installation, and MTS serial connections for seamless integration with other Innovate devices for data logging.

DISPLAY RANGE

Ethanol Content %: 0-100%
Temperature: -40-257 °F (-40-125°C)

KEY FEATURES

Ethanol Content
Error reporting for ethanol content sensor (Digital Display)
Fuel Temperature
Customizable exterior LED display
Programmable exterior LED color options
Selectable unit of measure in °F or °C
Programmable fuel temperature warning (outer LED)
2-Configurable analog outputs
Ethanol Content: 0v = 0%, 5v = 100%
Fuel Temperature: 0v = -40 °F, 5v = 257 °F (-40-125°C)

MTX-D: Ethanol Content Percentage & Fuel Temp Gauge Kit includes Gauge (Black Faceplate, Black Bezel), Silver Bezel & White Faceplate, Harness, Program Cable (Serial), Ethanol Content Sensor, Quick Start Installation Guide.

Please note that this is a universal fitment gauge, and installation may vary depending on the vehicle.

Show More Show Less

Hella Air Horn Kit

T#:592708

Part#: 3001651

Ships in 1 Business Day

$ 143.99

This product was last offered at the strikethrough price on
05-07-2026

$ 124.99 USD

Add to Wish List

Qty

$ 124.99 USD

Add to Wish List

Get noticed with this air horn kit from Hella!

VTT N5X/S55/N2X Triple Billet Cap Kit - Black - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122279

Part#: TRIPLECAPBLK1

Ships in 10 Business Days

$ 220.99 USD

Add to Wish List

Qty

$ 220.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

Vargas Ignition Coil Kit (Black) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309609

Part#: VTT-COIL-N5X-BLK

Ships in 10 Business Days

$ 167.99 USD

Add to Wish List

Qty

$ 167.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Black - BMW N52 N...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122264

Part#: VTTFILTERCAPBLK

Ships in 10 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

Spline Lock Crank Hub Solution

2X Entries Into Our F80 M3 Sweepstakes

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW 6 Series F06 (2013+)

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results