BMW Engine Parts for BMW X Series F15 (2014+)

Unlike traditional BMW engines, modern engines, like the B48 and B58, use a volume-flow-regulated oil pump. Instead of providing a consistent volume of oil, these new systems control oil supply at each individual operating range.

This Control Valve Solenoid is a critical component in the volume-flow-regulated oiling system. This piece seamlessly adjusts the oil pressure based on inputs from the DME. In the event of failure, this means the engine oil supply system may become restricted.

Thankfully, Bremmen Parts offers this high-quality, OE replacement Control Valve Solenoid at a fraction of Genuine price. Built with durability and fitment in mind, this component is an exact fit for your BMW.

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

Over time, accessory belts begin to wear out and crack. This can lead to the belt slipping, squeaking, or even snapping. Replace your belts and tensioners on a regular basis to ensure you don't end up stranded on the side of the road with a dead battery or over heated engine due to a bit of simple overlooked maintenance. This kit includes all of the items that will need replaced such as the belts, tensioners, and hardware.

For vehicles with dynamic or adaptive drive 

Fits the following BMWs:
F01/02 BMW 740i/Li/Li xDrive
F10 BMW 535i/i xDrive
F12/3 BMW 640i/i xDrive
F15 BMW X5 s/xDrive35i
F16 BMW X6 s/xDrive35i

BMW N55 S55 37cc Platinum Series Dish Piston Set - 84.5mm Bore is designed for high-performance applications, providing exceptional strength and durability for BMW engines. Turner Motorsport offers this premium piston set to enhance engine reliability and efficiency.

• High-Strength Material: Crafted from 2618 high-strength material for superior durability and performance.
• Quiet Start-Ups: Offset wrist pin design minimizes noise during engine start-ups.
• Premium Pins: Includes a .210” wall Premium Chrome Moly pin (Standard Series) or a .210” wall 9310 alloy pin (Extreme Duty Series) for added strength.
• Pressure Balance Groove: Features a pressure balance groove to improve piston stability and efficiency.
• Valve Accommodation: Designed to accommodate +1mm valve sizes for enhanced engine performance.
• Top-Quality Rings: Comes with premium steel top rings, Napier seconds, and round wire locks for optimal sealing and reliability.
• Recommended Clearance: Piston clearance of .0035” measured .850” from the bottom of the oil ring for precise fitment.

Genuine BMW Solenoid Valve (Solv)
 

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

This item fits the following BMW Chassis:
E70 X5M,E71 X6M,E70 X5,E71 X6,E82,E90,E92,E93,F01,F02,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4 X4,F30,F32,F33,F34,F36,F80 M3,F82 M4,F83

Fits BMW Engines including:
N55,N63,N63N,S55,S63,S63N

This eccentric shaft is a vital component of your BMW's N55 Valvetronic system, responsible for precise control of valve lift. In the N55 engine, the Valvetronic system uses intermediate levers between the camshaft and lifters to adjust valve lift dynamically. These levers are actuated by this eccentric shaft, which is rotated by an electronically controlled motor under the direction of the engine computer.

Eccentric shaft failure is a common issue in N55 engines, often caused by inadequate lubrication due to extended oil change intervals. The most frequent failure occurs when the eccentric shaft gear wears down, leading to disengagement from the motor's worm drive. Symptoms include multiple fault codes, such as P1014 (Shaft Parity Error), P1017 (Shaft Sensor Plausibility), P1023 (Valvetronic Adjustment Range), and P10E1 (Valvetronic System No Travel Detected).

If your BMW is experiencing Valvetronic-related fault codes, a failing eccentric shaft could be the source of the problem. Opt for this premium direct replacement from Bremmen Parts to restore your Valvetronic system's functionality and ensure a durable, high-quality repair.

New DCSS 39/50 High-Performance Pump – F90000295

• Highest flow in-tank brushed fuel pump offering from TI Automotive / Walbro
• No Internal check valve - ideal for racing applications to build oil pressure prior to start-up
• Featuring award-winning DCSS technology
• E85 compatible
• High-pressure relief setting - supports supercharger and turbo applications
• Capable of supporting 900+HP at 60PSI naturally aspirated applications
• Complete Pump and kit combination – TCD495

Fuel: GAS & E85

Horsepower: 900+ at 60PSI, naturally aspirated applications

Over All Pump Length: 131mm

Main Housing Diameter: 39mm

Lower Housing Diameter: 50mm

Fuel Inlet Diameter: 11mm OD

Fuel Outlet Diameter: 11mm OD

Flow Rate: 535LPH at 40psi

Test Voltage: 13.5 Volts

Introducing Turbosmart’s OPR V2 Turbocharger Oil Pressure Regulator, a cutting-edge solution launched in 2022 that ensures steady oil pressure for your turbocharger. This innovative regulator features a return-less design with an integrated 44 Micron Stainless Steel Mesh Oil Filter, providing robust performance and protection.

The OPR V2 is the first of its kind, utilizing Turbosmart’s proprietary flow control method to maintain optimal oil pressure regardless of engine oil variables like pressure or temperature. It guarantees a smooth oil flow to your turbocharger, safeguarding critical components such as Exhaust Drive, Back & Charge Pressures from excessive oil pressure that could lead to oil consumption and smoke.

Gone are the days of guesswork with restrictors and complex plumbing for oil pressure regulation. The OPR V2 simplifies the process with its return-less, inline installation and the convenience of a built-in 44 Micron Oil Filter. This filter, made of serviceable and replaceable Stainless Steel Mesh, adds an extra layer of defense against engine oil debris that could harm your turbocharger.

Key Features:

Innovative Patent Pending Design Durable Aluminium (6262 T6) Anodised Body & Valve Regulated Oil Pressure Compatible with Most turbochargers Integrated Stainless Steel (304) Mesh Oil Filter -4AN Inlet and Outlet for easy installation 1/8 NPT Sensor/Gauge Port for monitoring Directional Inlet Feed Logic for optimized performance Laminar Flow Output for consistent oil delivery Compatible with all Engine Oils Designed and Manufactured in Australia