Is your BMW throwing emissions related codes? While we're primarily a BMW performance parts house, we understand the importance of maintaining your emissions system to pass inspection in your area and keep your check engine light off. Pick up your emissions related parts from Turner Motorsport.
Vargas has developed a solution to problematic PCV systems! Stock diaphragms on the gen-1 B58 Valve cover are fragile and can crack or tear over time. This can cause loss of crankcase vacuum and smoking. The VTT PCV cap replaces the factory plastic cap with a billet aluminum piece which uses a Billet Banjo fitting, and VTT's Vaccum/Boost adapter to move vacuum directly from the head ports to the manifold. This cap will also allow you to run a catch can on the low side if desired. VTT Recommends using this cap alongside their High Side Catch Can and crankcase breather for maximum efficiency. Installation is as simple as popping the stock cap off, removing the diaphragm, and placing the VTT components in place. Kit Includes: One Billet PCV Cap One Billet Banjo Fitting One Vaccum/Boost adapter One line with built-in check valve
Show More Show Less
WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
The VTT B58/S58 Head Port Block-Off kit is designed to either seal off the factory head ports used by the OEM low-side PCV system. These ports in the cylinder head utilize engine vacuum to evacuate crankcase gases, but in the process, can allow oil to enter the intake manifold, leading to valve carbon buildup and other performance issues over time. The Block-Off kit offered by VTT completely seals the factory head ports to prevent oil intrusion and unwanted vacuum leaks. This kit does NOT require any tapping, meaning no metal to get into the engine, etc. You simply tap the plugs into place. Key Features Eliminates oil draw-through into the intake manifold Prevents carbon buildup on intake valves Utilizes precision-machined plugs for boost sealing Fully reversible — Block-offs can be removed if needed No tapping is required. Easy install, by tapping the blocks into place.
Show More Show Less
Universal kit with a catch can and rubber hose; for retrofitting on a variety of vehicles. Carbon fiber catch can prevents a harmful buildup of oil inside of the turbocharger, intake manifold, intercooler and piping. Separates oil particles from PCV/CCV air Defends intercooler, intake system, and essential components from oil blow-by Made from lightweight carbon fiber Compact design makes for easy engine bay placement Checking fluid levels made easy with built in sight tube Comes complete with mounting bracket, hose, all necessary clamps, fittings, and mounting hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
il venting and circulation continues to be a problem on BMW engines and the N20 engine is not immune from this. The existing stock system does a poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. Performance issues are caused by oil sneaking by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media and chemical blasting of the intake valves to strip away the oily buildup we have seen. Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine. The Mishimoto Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles. This item fits the following BMWs with the N20 or N26 turbo engine: 2014-2016 F2X 228i 228i xDrive 2012-2016 F3X 320i 320i xDrive 328i 328i xDrive 428i 428i xDrive WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.
Show More Show Less
This kit uses VTTs popular modular catch can and couples it with a custom CNC 6061 bracket, VTT CNC banjo fittings, VTT 5 ply silicone hose, and Push lock fittings. Install is simple, takes about 30 minutes to 2 hours depending on your skill level, and requires removing one factory hose to install the VTT hoses. Retains OEM fit and finished when installed. This kit stands out from others on the market by using high-quality AN fittings and VTT Banjo adapters. Kit contents: One Catch Can One CNC 6061 bracket Two -10 Low Profile CNC Banjo Fittings Two -10 VTT 5-Ply silicone Vacuum hoses Two -10 Push Lock Fittings Two spring clamps Fits all 2019+ G Series 3/4 BMW vehicles with the B58TU engine. Fits all 2015+ F series BMW vehicles with the B58 engine
Show More Show Less
The VTT B58 Head Port Check Valve Kit is designed to convert the factory head ports used by the OEM low-side PCV system. These ports in the cylinder head utilize engine vacuum to evacuate crankcase gases, but in the process, can allow oil to enter the intake manifold, leading to valve carbon buildup and other performance issues over time. VTT's Billet Check Valve kit converts the head ports into a robust internal PCV system using precision-engineered check valves. These one-way valves allow vacuum to function as intended while blocking boost pressure from entering the crankcase or charge tract.
Show More Show Less
