BMW Intake Parts for BMW 2 Series F23 (2015+)

Bring your aFe filter back to life with a Restore kit from aFe. Included is filter cleaner & replacement oil. These air filter oils is designed to not harm MAF sensors, while allowing the filter to catch as much debris as possible.

Used for Pro 5 R filters

Engines make more power when you're able to move as much air and fuel as possible through them. However, air density is just as important as air volume. Cooler air is denser air, so in addition to keeping your engine cool, it's important to make sure that your intake charge is as cool as possible. Turner Motorsport's upgraded intercooler works to reduce air temperatures with a bare minimum of pressure drop. Less pressure drop means less restriction, and a turbocharger that doesn't have to work as hard. This results not only in a longer service life for your turbocharger, but a substantial increase in performance as well.

The stepped design increases volume and surface are in a limited space by adding an additional smaller core at the top of the intercooler. Both cross sectional area and frontal surface area are increased by a whopping 56%, with a design that still weighs under 20 pounds. On the stock intercooler, the temperature differential between the inlet and outlet sides of the intercooler represented a 95 degree drop. With the Turner Motorsport intercooler, that drop was increased to a chilling 140 degrees. The dyno results don't lie: as a bolt-in upgrade, expect gains of 18 wheel horsepower and 10 lb/ft of torque. With a tune and supporting modifications, further gains are possible, up to 36 horsepower and 28 lb/ft of torque.

This cast aluminum intercooler features an attractive, easy to clean matte black finish, with etched Turner logos on the front and bottom. If you're looking for the ultimate cooling system upgrade for your turbo BMW, look no further.

• Cast aluminum construction
• Bar and plate design
• 56% increase in frontal surface area & cross sectional area
• Decrease in temperature of 45 degrees from inlet side to outlet side (95 degree drop stock on outlet side vs. 140 degree drop on Turner outlet side)
• Significantly less restriction (pressure drop of consistently 0.75 psi vs. 1.5-2.5 psi stock)
• +18HP/10TQ (+36HP/28TQ with tune and supporting mods)
• Weighs under 20 lbs.
• Overall size: 520mm wide, 210mm tall
• Mounting hardware inlcuded

Upgrade to the following OE Intercoolers: 17517600531, 17517600530, 17517618809

Fits the Following BMWs:

F22 F23 228i 228i M235i M235ix

F30 F31 F32 F33 F34 F36 328i 328ix 335i 335ix 428i 428ix 435i 435ix

This is a drop-in stock replacement aFe performance air filter that installs into your BMW's factory airbox. This version has an oil-free filter media for less maintenance. For the best flowing filter, with the best performance gain, we always recommend the standard aFe "Pro5R " filter (which has a blue pre-oiled filter media), but this oil-free filter flows only slightly less than the blue Pro5R style aFe filter, and requires no re-oiling after cleaning the filter.

Fits in vehicles with the following engines: B46 2.0L, B58 3.0L

HP Gain: +13hp
Trq Gain: +13ft-lbs
Airflow: +28% over stock

aFe has engineered the Momentum GT intake to outperform the stock air box and deliver substantial power and torque gains over the factory system. The B58 3.0L Turbo benefits from aFe's oversized cotton filter element in a Rotomold plastic housing that blocks heat saturated air while flowing more volume of cooler dense air. The system has been CAD designed to achieve the maximum volumetric flow rate into the turbo. The intake tube is a smooth, unobstructed single piece from the air inlet to the airbox and incorporates a port for the air flow sensor. aFe's advanced engineering and design have made this a direct bolt-in intake upgrade.

The aFe filter has been designed specifically for this application and uses aFe's high flow/low maintenance design. The ProDry S filter has an oil-free filter media for less maintenance. For the best flowing filter, with the best performance gain, we always recommend the standard aFe Pro5R filter (which has a blue pre-oiled filter media), but this oil-free filter flows only slightly less than the blue Pro5R style aFe filter, and requires no re-oiling after cleaning the filter.

Features:

• +13 HP and +13 lbs. x ft. Torque max gains
• Outflows factory intake by up to 28%
• High Quality One-Piece Roto-Molded Sealed Housing with Auxiliary Air Scoop
• CAD-Designed Roto-Molded Intake Tube
• Lightweight high gloss, clear-coated 2 x 2 twill-weave carbon fiber trim on housing for styling
• Built-In Sight Window Provides Easy Inspection of Filter Without Disassembly
• Pro 5R oiled 5-Layer Progressively Finer Mesh Cotton Gauze Oiled Media for Maximum Performance
• Unique (Patent Pending) Filter-to-Housing Interface for Easy Installation
• No Cutting or Drilling on factory Parts for Faster Installation

This is a drop-in stock replacement aFe performance air filter that installs into your BMW's factory airbox. This version used aFe's highest flowing filter media, which uses a lightly oil gauze to filter out dirt and particulates, while allowing more air to flow to the intake. We also carry this filter in the "ProDry" grey filter media, which is oil-free for only slightly less performance and no maintenance.

Fits in vehicles with the following engines: B46 2.0L, B58 3.0L

On turbocharged motors, the intake piping is put under constant pressure while the engine is running, and has to hold that pressure without leaking. Unfortunately the smallest amount of damage or defect on the intake hoses and the pressure can cause a leak, leaving you without proper boost pressure.  Replace your leaking pressure pipe and stop loosing boost.

Product Features and Specifications:

• +13 HP / +13 lbs. x ft. Torque max gains
• Outflows factory intercooler tube by 18%
• Retains the factory style throttle body and intercooler quick connections made from 6061-T6 Billet Aluminum
• 2-1/2" to 3" Cold-Side mandrel-bent aluminum tubing
• Powder-coated wrinkle-black for heat resistance
• 1/8" NPT ports, are provided for connecting pressure sensors or water methanol injection
• 5-Ply Polyester Reinforced Silicone coupling for strength
• Includes premium stainless steel clamps for a secure fit
• For use with the factory or aFe intercooler (46-20231)
• Includes hardware for a hassle-free installation
• For use with manual transmission vehicles ONLY