BMW Engine Parts for BMW 3 Series F34 (2014+)

Upgraded Fuel Pump Control Module - Dual Ball Bearing Fan - EKPM3 ...

T#:28304531

Part#: EKP-HW06-F-SF

In Stock

$ 209.99 USD

Add to Wish List

Qty

$ 209.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half-bridge IC. When the half-bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

BMW B46 B48 B58 Ethanol Content Sensor

We Price Match - Give Us A Call or Chat!

T#:29500150

Part#: 100.1037

In Stock

$ 98.99

This product was last offered at the strikethrough price on
08-24-2026

$ 94.99 USD

Add to Wish List

Qty

$ 94.99 USD

Add to Wish List

BMW B46 B48 B58 Ethanol Content Sensor is a genuine Continental (VDO) Flex Fuel E85 sensor designed to accurately measure the ethanol-to-gasoline ratio in your vehicle's fuel system.

Accurate Measurement: Measures the ethanol content in fuel, providing precise data for optimal engine performance and fuel management.
Flexible Compatibility: Works with a blend of ethanol and gasoline, suitable for vehicles with appropriate fuel lines, injectors, and ECU calibration.
Quick-Connect Installation: Features quick-connect style fuel connections for easy installation in the main fuel feed line.
Integrated Fuel Analysis: All fuel passes through the sensor before reaching the fuel rail, allowing for accurate ethanol percentage readings sent to the vehicle's DME or ECU.
Standard Fittings: Both inlet and outlet connections are 3/8" SAE sized fittings for straightforward integration with existing fuel systems.

This ethanol content sensor is essential for vehicles running flex fuel, ensuring that the engine receives the correct ethanol ratio for peak performance and efficiency.

Show More Show Less

BMW F Chassis Upgraded Fuel Pump Control Module - Noctua Fan - EKPM3 ...

This service will not work for M-Cars or any B-Series motors

T#:28304534

Part#: EKP-HW06-F-NF

In Stock

$ 239.99 USD

Add to Wish List

Qty

$ 239.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. Includes 40mm Noctua Silent Fan! How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half-bridge IC. When the half-bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

F3X/F2X - N20 EKP PNP Cooler Kit

A Must For Cars With Upgraded LPFPs

T#:26471604

Part#: AT226F22BLA501N2

Ships in 1 Business Day

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With 5015 Fan or 60mm Noctua Fan (depending on choice) 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

F3X/F2X - N55 EKP PNP Cooler Kit

A Must For Cars With Upgraded LPFPs

T#:26471608

Part#: AT223F22BLA501N5

In Stock

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

B58 Supra Fuel Pump Retrofit Extension Harness - F3X B58

T#:2810078

Part#: B58PUMPHARNESS

In Stock

$ 45.00 USD

Add to Wish List

Qty

$ 45.00 USD

Add to Wish List

Use this harness to run an improved "Supra" fuel pump in your B58 car. This harness allows you to run the G20 M340i/Supra Fuel pump (13518631642) on your F Chassis B58 car.

F3X/F2X - N55 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471609

Part#: AT231F22BLA40MN5

In Stock

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With a single 40mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

F3X/F2X - N20 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471605

Part#: AT234F22BLA40MN2

Ships in 1 Business Day

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With a single 40mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

OEM VDO Camshaft Position Sensor - BMW B48/46 B58 N20/26

We Price Match - Give Us A Call or Chat!

T#:19197278

Part#: 13627633958

Ships in 2 Business Days

$ 115.99 USD

Add to Wish List

Qty

$ 115.99 USD

Add to Wish List

Camshaft position sensors are electrical sensors that monitor the rotational speed and position of a camshaft. This signal is used by the DME to control fuel delivery and spark timing. If your camshaft position sensor is faulty, it can result in check engine lights, rough idle or running conditions, limp mode, or no starts. Replace your cam position sensor with this high-quality replacement to restore smooth engine operation.

Show More Show Less

Fuel-It! B58 BMW High Pressure Fuel Pump (HPFP) Upgrade - Stage 1 ...

T#:17106920

Part#: BMW-B58HPFP-A01

Ships on Oct 2, 2026

$ 1,499.00 USD

Add to Wish List

Qty

$ 1,499.00 USD

Add to Wish List

Introducing the new B58 BMW HPFP upgrade kit from Fuel-It! Replaces your factory high-pressure fuel pump with a higher capacity pump capable of supporting 30% more flow with Stage1 or 60% more flow with Stage2! Includes all required installation hardware for a clean plug and play install. Includes: Upgraded High-Pressure Fuel Pump (HPFP) Billet Adapter Plate Billet Center Alignment Tool Low-pressure Line (Triple lined crimped fittings PTFE/SS/Nylon Braided) Custom Harness and Hardware

Show More Show Less

Fuel-It! F-Chassis B58 Stage 3 LPFP Upgrade

T#:17837993

Part#: B58STG3LPFP

Back Ordered

$ 829.99 USD

Add to Wish List

Qty

$ 829.99 USD

Add to Wish List

This is a complete Low Pressure Fuel Pump (LPFP) upgrade for those customers that need the additional capacity to meet their power goals on pump gas, race gas, or E85. It utilizes a stock pump for the primary pump so that your EKP operates as intended by the factory eliminating potential errors for current draw and the secondary pump then runs under high boost only. For power levels up to 700whp we'd recommend using the standard 450 pump and beyond 700whp we'd recommend upgrading to the 525 pump. F-Series B58 (Gen 1) Stage 3 assemblies include: New stock LPFP Secondary pump assembly Secondary wiring harness Walbro filter Walbro 450 pump (F90000274) Compatible with the following vehicle production dates: 1' F20 LCI (05/2014 — 06/2019) 1' F21 LCI (05/2014 — 06/2019) 2' F22 (06/2014 — 06/2017) 2' F22 LCI (09/2016 — 12/2019) 2' F23 (06/2014 — 06/2017) 2' F23 LCI (09/2016 — 12/2019) 3' F30 LCI (09/2014 — 10/2018) 3' F31 LCI (09/2014 — 06/2019) 3' F34 GT LCI (09/2015 — 12/2019) 4' F32 (04/2015 — 02/2017) 4' F32 LCI (05/2016 — 12/2019) 4' F33 (03/2015 — 02/2017) 4' F33 LCI (05/2016 — 12/2019) 4' F36 Gran Coupé (05/2014 — 03/2017) 4' F36 Gran Coupé LCI (05/2016 — 12/2019) *Note: Secondary pump can NOT run full time. We recommend using a Hobb's switch to trigger the secondary under high boost. See the installation process here: https://www.youtube.com/watch?v=YoPf0F7PBt8

Show More Show Less

F3X/F2X - B58 EKP PNP Cooler Kit

A Must For Cars With Upgraded LPFPs

T#:26471615

Part#: AT224F22BLA501B5

Ships in 1 Business Day

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

F3X/F2X - B58 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471614

Part#: AT232F22BLA40MB5

Ships in 1 Business Day

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With a single 40mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

Fuel-It! Low Pressure Fuel Pump Upgrade Stage 2 - N55 F-Series ...

T#:403295

Part#: FILPFPK5

Back Ordered

Sale - Save 2% $ 649.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 634.84 USD

Add to Wish List

Sale - Save 2%

$ 649.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 634.84 USD

Add to Wish List

This is a complete Low Pressure Fuel Pump (LPFP) upgrade that replaces your weak stock LPFP assembly with a high-flow E85-certified one. Standard Kit Includes: A brand new OEM LPFP bucket that is upgraded with a new Walbro 450 or 525 pump and filter. A new E85 compatible Walbro 450 pump (F90000274) that flows 50% more fuel than stock Optional A new E85 compatible Walbro 525 pump (F90000285) that flows 65% more fuel than stock NOTE: Owners with I-Drive may get a Fuel pump warning on the screen that says "Continued driving is possible. Have the system checked by your BMW center as soon as possible." As long as the car is running fine and does not exhibit any other symptoms, there is not an issue with the pump and this can be ignored. If you have any questions about this please feel free to contact us. Upgraded pumps pull more current, so if your EKP (LPFP control module) is weak, it may overheat causing it to shut down and need to be replaced. If this is a concern for you check out our Stage 3 fuel pump upgrade kits that retain the stock LPFP and add a secondary pump.

Show More Show Less

Fuel-It! Flex Fuel Kit - N20/N26 F Chassis

T#:21275574

Part#: FFK-N20/6F-FK

Ships on Oct 2, 2026

$ 369.99 USD

Add to Wish List

Qty

$ 369.99 USD

Add to Wish List

This is a complete plug and play kit to install a Bluetooth ethanol sensor in about 30 minutes! The kit includes the following: New 5/16" E85 compatible fuel lines for your engine bay Genuine Continental ethanol sensor Fuel-It! Bluetooth analyzer Plug and play harness Includes both Bluetooth App & 5v analog output for JB4 or flash tuning NOTICE: If you have an N26 motor type, you will need to retrofit the HPFP supply line to part number 13537585415 to be compatible with this kit. *For the BMW F-series JB4 platform connect the white wire to position #14 on the JB4 25 pin harness. Select WMI Ethanol Setup option 1 to enable pin location 14/15/16 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

Fuel-It! Bluetooth Flex Fuel Kit - B46/B48/B58

T#:21209854

Part#: FFK-B464858

Ships on Oct 2, 2026

Starting at $ 479.99 USD

Add to Wish List

Starting at $ 479.99 USD

Add to Wish List

If you're running E85 or ethanol mixes in your BMW, you need this kit! As many of you know the BMW motors can be very picky about how much ethanol you run to achieve peak performance but not run lean. Consequently, BMS have put together a kit enabling you to easily install an ethanol sensor with no permanent modifications needed. You will simply remove your low pressure fuel line in the engine bay and plug in our kit. It's a complete plug and play solution that utilizes our Bluetooth app to monitor your ethanol content. When you are ready to return to stock, you will simply remove the kit and re-install the stock fuel line. The complete kit includes the following: Genuine Continental ethanol sensor Fuel-It! Bluetooth Universal Analyzer Two stainless steel braided fuel lines with black nylon sheathing to protect your other engine bay components Proprietary custom billet fittings for plug and play OEM integration One wiring harness with Posi-tap connector Bluetooth Model Supports stand-alone Bluetooth operation with the Fuel-It! app *For the JB4 platform connect the white wire to position #4 on the JB4 25 pin harness. Select WMI Ethanol Setup option 0 to enable pin location 2/3/4 flex fuel input. *Ethanol Sensors don't actually read the ethanol content, the readings are based on the absence of gasoline, so if your fuel is contaminated your ethanol readings may be artificially elevated.

Show More Show Less

Fuel-It! Elite Port Injection Kit With 950cc Injectors & Fuel Line ...

T#:26038542

Part#: BMW-EPI-950

Ships on Oct 2, 2026

$ 1,188.00 USD

Add to Wish List

Qty

$ 1,188.00 USD

Add to Wish List

This kit is designed to enhance performance by adding six supplemental low-pressure fuel injectors, capable of supporting 1000+ WHP on E85 and similar high-performance fuels.

Crafted with precision, the manifold spacers are CNC machined and anodized to ensure durability and prolonged service life. Each kit comes complete with all necessary installation hardware, a gasket set, and a plug-and-play fuel line adapter for seamless integration.

The Elite kit stands out with its sleek black anodized finish and includes an additional return port, an upgraded fuel line, and enhanced machining to accommodate a wider range of applications, including the BMW S55 engine.

A port injection controller is not included. This is required for a complete installation.

Show More Show Less

Fuel-It! B58 BMW High Pressure Fuel Pump (HPFP) Upgrade - Stage 2 ...

T#:13003684

Part#: BMWB58HPFPSTG2

Ships on Oct 2, 2026

$ 1,499.00 USD

Add to Wish List

Qty

$ 1,499.00 USD

Add to Wish List

Introducing the new B58 BMW HPFP upgrade kit from Fuel-It! Replaces your factory high-pressure fuel pump with a higher capacity pump capable of supporting 30% more flow with Stage1 or 60% more flow with Stage2! Includes all required installation hardware for a clean plug and play install. Includes: Upgraded High-Pressure Fuel Pump (HPFP) Billet Adapter Plate Billet Center Alignment Tool Low-pressure Line (Triple lined crimped fittings PTFE/SS/Nylon Braided) Custom Harness and Hardware

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW 3 Series F34 (2014+)

Sub-Categories

Upgraded Fuel Pump Control Module - Dual Ball Bearing Fan - EKPM3 ...

BMW B46 B48 B58 Ethanol Content Sensor

BMW F Chassis Upgraded Fuel Pump Control Module - Noctua Fan - EKPM3 ...

F3X/F2X - N20 EKP PNP Cooler Kit

F3X/F2X - N55 EKP PNP Cooler Kit

B58 Supra Fuel Pump Retrofit Extension Harness - F3X B58

F3X/F2X - N55 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

F3X/F2X - N20 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

OEM VDO Camshaft Position Sensor - BMW B48/46 B58 N20/26

Fuel-It! B58 BMW High Pressure Fuel Pump (HPFP) Upgrade - Stage 1 ...

Fuel-It! F-Chassis B58 Stage 3 LPFP Upgrade

F3X/F2X - B58 EKP PNP Cooler Kit

F3X/F2X - B58 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

Fuel-It! Low Pressure Fuel Pump Upgrade Stage 2 - N55 F-Series ...

Fuel-It! Flex Fuel Kit - N20/N26 F Chassis

Fuel-It! Bluetooth Flex Fuel Kit - B46/B48/B58

Fuel-It! Elite Port Injection Kit With 950cc Injectors & Fuel Line ...

Fuel-It! B58 BMW High Pressure Fuel Pump (HPFP) Upgrade - Stage 2 ...

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results