BMW Engine Parts for BMW 3 Series F34 (2014+)

Magnetic Sump/Oil Pan Plug

T#:22723756

Part#: MMR03-0504

Ships in 2 Business Days

$ 37.99 USD

Add to Wish List

Qty

$ 37.99 USD

Add to Wish List

MMX Oil Filler Cap - Black

For Most BMW Models 2007 Onwards or Mini Models

T#:4552062

Part#: MMR03-0102-BL

Ships in 1 Business Day

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

MMX's Performance billet oil filler cap machined from billet T-6061 aluminum has been designed to instantly give your engine bay an subtle aesthetic upgrade. This cap comes in a Black finish. *Note: After exposure to excessive heat over prolonged periods, overall finish fading can occur. Reusing of original seal is required.

Show More Show Less

MMR Low Temp Thermostat - N54/N55

For 2008 and up models

T#:4565826

Part#: MMR17-0101

Back Ordered

$ 70.99 USD

Add to Wish List

Qty

$ 70.99 USD

Add to Wish List

MMR's Low Temp Oil Thermostat is one of the easiest ways to increase your oil cooling capability. Rated to maintain the oil temps at about 194F (90c) to 230F (110c). Machined from aircraft grade T-6061 aluminum and anodized in MMR's trademark finish for durability. Installation is easy as it fits right into the OEM oil thermostat housing on the N54 and N55. Highly recommended for cars used on the track or with a higher power and torque output than stock.

Show More Show Less

S55 / N55 One-Piece Crank Hub Upgrade Kit - 4-Pin

T#:19891361

Part#: MMR20-1004

Ships in 2 Business Days

$ 1,064.99 USD

Add to Wish List

Qty

$ 1,064.99 USD

Add to Wish List

Both the N55 and S55 engines are plagued by the same issue when chasing high horsepower numbers... the dreaded crankhub failure. Fortunately MMR Performance has released an upgraded version of their already stout single-piece crankhub, but this time offering a 4-pin dowelled location that locks onto the front of the crankshaft. This configuration eliminates the multi-piece crankhub with friction discs in favor of a more robust single piece crankhub. Recommended for high-powered cars over 700 Horsepower

Show More Show Less

MMR Crank Hub Kit - N55/S55

T#:4565824

Part#: MMR20-1003FK

Ships in 2 Business Days

$ 849.99 USD

Add to Wish List

Qty

$ 849.99 USD

Add to Wish List

Anyone with a modified N55/S55 knows the risks involved with the OEM Crank Hub. When the engine simply can't handle the stresses its put under or the design is such that it simply does not support extreme conditions, issues can arise. Under certain conditions, the N55/S55 crank hub likes to spin, without warning and even when the engine is in perfect health. MMR has produced a EN36 machined billet one-piece crank hub heat treated with a 0.75mm case hardening which makes it extremely durable. Due to the one-piece design, it ensures that the friction plates cannot slip. This offers a huge jump in reliability when paired with a new properly torques crank bolt. Installation is requires no drilling or modification to the OEM crankshaft ensuring a perfect fit! Included in this kit is MMR's T-6061 machined billet aluminum capture plate anodized in their trademark finish. The MMR Performance capture plate secures the head of the OE crank bolt and prevents it from turning or being able to loosen. *Installation recommended by a professional shop or technician.

Show More Show Less

Ferrea High Performance Valve Spring Kit for BMW N55/S55

T#:23416526

Part#: FER-HPVSK-N55

Ships in 3 Business Days

$ 1,049.99 USD

Add to Wish List

Qty

$ 1,049.99 USD

Add to Wish List

Maximize your N55 or S55 engine's performance with Ferrea Valve Springs and Retainers, precision components crafted from chromoly alloy. These springs undergo special thermal treatment, ensuring exceptional durability even in extreme racing conditions. Addressing issues like valve binding, breakage, and float, Ferrea valve springs are meticulously heat-treated and stress-relieved, providing stability for high-lift and high-RPM racing engines while minimizing load loss. Precision CNC machined titanium retainers offer superior strength and stability. Ferrea's Spring Seat Locators, made from 4140 chromoly alloy, guarantee precise tolerances and a flat, parallel spring pad with a hard Nitride surface treatment for exceptional toughness and anti-wear characteristics. Please note that installation requires the expertise of an engine builder.

Show More Show Less

MMX Performance - 4-Pin One-Piece Crank Hub Upgrade Kit - With MMR Ca...

T#:45039725

Part#: MMR20-1004FK

Ships in 3 Business Days

$ 1,227.99 USD

Add to Wish List

Qty

$ 1,227.99 USD

Add to Wish List

The centerpiece of this MMX kit is the UK-made CNC-machined one-piece crank hub, created from billet EN36 steel that's heat-treated with a 0.75mm case hardening, making it incredibly strong and durable. Included are four aerospace precision-machined dowels that mechanically lock the hub to the end of the crank itself, plus a brand new OE bolt. Installation of these dowels is certainly not a DIY job. But, to make the job easier for the professionals, ensuring that the required crank modifications are made safely and accurately, the MMX kit also includes a full installation jig that includes a bolt-on drilling guide, a location bolt for this guide, plus an HSS rolled high-speed drill bit. Together, the single-piece design combined with the four-pin location ensures that there is simply no way that the friction plates can ever slip. With the new OE crank bolt tightened appropriately, this delivers a transformational improvement in reliability and peace of mind versus the OE version. Also included is the MMR Crank Bolt Capture Plate. This adds one additional layer of defense, preventing the crank bolt from being able to back out and loosen over time, ensuring everything is tightly held together as intended.

Show More Show Less

Cometic Multi-layer Steel Head Gasket - B58

T#:25241786

Part#: COM-HG-B58G1

In Stock

$ 244.99

This product was last offered at the strikethrough price on
05-06-2026

$ 226.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 244.99

This product was last offered at the strikethrough price on
05-06-2026

$ 226.99 USD

Limited Qty Sale

Add to Wish List

Constructed with multiple layers of stainless steel and a proprietary coating, the MLX gasket offers superior sealing and load distribution capabilities. The coating is designed to withstand high temperatures and pressures, preventing gasket failure due to fatigue or stress. Additionally, the unique embossed sealing bead provides further sealing ability.

Show More Show Less

MMX Oil Filter Housing - Black

T#:4552065

Part#: MMR03-0101-BL

Ships in 2 Business Days

$ 142.99 USD

Add to Wish List

Qty

$ 142.99 USD

Add to Wish List

If you are looking for peace of mind over the prone to cracking OEM plastic housing cap, this oil filter housing cap by MMX may be exactly what you are looking for. Composed of billet aluminum, this cap is light, durable, and dresses up your engine bay! Comes finished with a polished anodized dark anthracite coating. Installation is simple as it can be replaced while completing an oil change. *Note: After exposure to excessive heat over prolonged periods, overall finish fading can occur.

Show More Show Less

BMW N55 S55 Ferrea High Performance Valve Kit

T#:23416508

Part#: FER-HPVK-S55-T-3

Ships in 3 Business Days

$ 929.99 USD

Add to Wish List

Qty

$ 929.99 USD

Add to Wish List

Increase the power output of your N55/S55 engine with the high-performance Ferrea valve kit. Renowned as the industry's most reliable extreme-duty valves, they're meticulously crafted from aerospace-grade alloys, employing an exclusive two-step slow forging process for optimal grain flow and material structure integrity. A 48-hour heat treatment and stress-relieving process enhance molecular integrity. The valves feature avionics-quality hard chrome and a specially applied hard tip. Standard size: 32mm intake / 28mm exhaust, with a triple groove valve design. Compatible with factory valve locks ("Valve Keepers"), the kit includes 12x Intake Valves and 12x Exhaust Valves for a comprehensive engine upgrade!

Show More Show Less

5150 AutoSport Pro-Series Turbo Build Kit - BMW N55 Stage 2

T#:31755188

Part#: 5150-TBK-N55-100

Ships in 3 Business Days

$ 6,099.99 USD

Add to Wish List

Qty

$ 6,099.99 USD

Add to Wish List

The 5150 AutoSport Pro-Series Turbo Build Kit is made for high horsepower and turbocharged performace.

ARP Head Stud Kit - B58 - ARP2000

T#:25241790

Part#: B58-S-203-4705

Ships in 3 Business Days

$ 399.99 USD

Add to Wish List

Qty

$ 399.99 USD

Add to Wish List

This ARP2000 Head Stud Kit 203-4705 is designed for the turbocharged inline 6-cylinder B58 engines found in various BMW chassis and the Toyota GR Supra A90/A91. As you increase the power output of your engine beyond its factory specifications, the head and block may start to separate, causing factory bolts to stretch and fail. ARP Head Studs are stronger than factory bolts, ensuring your race engine stays together even under extreme conditions.

Show More Show Less

SP Components Connecting Rod Set - B58

T#:25241785

Part#: SP-CRS-B58

Ships in 3 Business Days

$ 1,099.99 USD

Add to Wish List

Qty

$ 1,099.99 USD

Add to Wish List

SP Components is renowned for their premium aftermarket forged H-beam rods, earning a strong reputation in the industry. These connecting rods, characterized by their lightweight and robust nature, boast an enlarged mating surface that significantly enhances their ability to withstand heavy loads. Specifically engineered to replace BMW part #11248623419 and #11247589671, these rods are tailored for BMW B58 engines featuring a 148mm connecting rod length. In addition to their reliable construction, these rods come equipped with balanced matching weights and include ARP rod bolts. With a robust capacity to endure speeds of up to 8,500 rpm, they are exceptionally well-suited for high-performance applications. Furthermore, these rods demonstrate the capability to meet the demands of high-horsepower forced induction engines generating up to 900HP, providing the added assurance of ARP Connecting Rod Bolts Included.

Show More Show Less

Performance N55 Main Bearing Set

T#:26238415

Part#: 5150-HPMBS-N55

Ships in 3 Business Days

$ 549.99 USD

Add to Wish List

Qty

$ 549.99 USD

Add to Wish List

5150 High Performance Coated Main Bearing Sets are made for the demands of high performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use, but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market.

Show More Show Less

ARP Head Stud Kit - BMW N55/S55

N55 Engines must be drilled & tapped for proper installation

T#:23416542

Part#: ARP-HSK-S56-CA

In Stock

$ 999.99 USD

Add to Wish List

Qty

$ 999.99 USD

Add to Wish List

MMX Oil Pressure Gauge Adaptor - Dark Anthracite

T#:4552049

Part#: MMR03-0502-KP

Special Order: No Guaranteed ETA

$ 21.99 USD

Add to Wish List

Qty

$ 21.99 USD

Add to Wish List

The MMX Performance billet adaptor is a helpful addition for those wishing to run an auxiliary oil pressure or oil temperature gauge. The adaptor replaces the plug that can be found on the oil cooler thermostat assembly with a 1/8NPT gauge adaptor.

Show More Show Less

MMX Oil Thermostat Dress-Up Caps - Black

T#:5269482

Part#: MMR03-0502BL

Special Order: No Guaranteed ETA

$ 136.99 USD

Add to Wish List

Qty

$ 136.99 USD

Add to Wish List

This dress-up kit offers a high-quality aesthetic update to the OE thermostat cover. Thermostat dress up kit for the BMW N55, N54, and S55 engines manufactured from T6061 billet aluminum. Installation is extremely easy and dresses up the engine bay nicely. *Note: After exposure to excessive heat over prolonged periods, overall finish fading can occur.

Show More Show Less

MMX High Performance Oil Filter - BMW B58 & B58TU

T#:29035359

Part#: MMR17-1502

Special Order: No Guaranteed ETA

$ 81.99 USD

Add to Wish List

Qty

$ 81.99 USD

Add to Wish List

Get rid of the notorious B58 oil filter disintegration problem forevermore with the MMR Performance Oil Filter. By replacing the factory paper filter element with MMR’s advanced high-flow, high-filtration stainless steel filter unit, you will protect your engine from the big bills (and potentially worse) caused by the OE filter’s collapse failure. The oil filters on BMW’s B58 & B57 3.0 6-cylinder engines (both petrol and diesel) suffer from a well-documented quality problem with the factory paper-element oil filter. At service time, when removal of the filter is attempted, the bottom section frequently breaks away from the disintegrated filtration material. This leaves the broken base stuck in the oil filter housing and an expensive removal/replacement job to extract the remains and fit a new housing. Such is the problem that there’s even an official BMW technical bulletin to warn their dealers of this. The MMR replacement Oil Filter is a pretty special replacement filter. It fixes this annoying problem once and for all. The MMR Oil Filter element is made from a pleated high-flow stainless steel micronic filter cloth – a medical-grade material guaranteed to filter out oil contamination right down to 20 Microns, ensuring far better protection than paper-based filters can achieve. As well as this exceptional filtration, the filter material allows for five times the flow of comparable paper oil filters. Its design provides consistent filtering across entire filter surface. The failure of the factory oil filter generally just leads to a large bill to extract the damaged remnants. However, more worryingly, it has occasionally been known to lead to broken pieces of filter media running through the small oilways and orifices of the engine’s lubrication system, risking blocking the oil running round the bearings and VANOS system and causing much greater mechanical damage before it is caught. The MMR Oil Filter is a reusable unit which can be used over and over again. As long as it is thoroughly cleaned at each oil change, it will last the lifetime of the vehicle and keep on protecting the engine just as it did when new. However, proper cleaning is not necessarily a DIY job, as it requires the use of a suitable solvent to break down the old oil, and cleaning from the inside out with compressed air to remove any risk of debris remaining. If you have any doubts about this, we recommend as best-practice to change filter with every oil-change. The MMR Oil Filter is a lifetime reusable filter. But to resuse and avoid any future loss of filtration or oil flow, it is essential that it is thoroughly cleaned at each oil change as follows: Remove MMR Oil Filter from filter housing Remove 3x O-Rings from MMR Oil Filter prior to Step 3, as fuel will degrade and cause damage to these rubber/Viton components. Soak the filter one of the following fluids for 5-10 minutes – Petrol/Gasoline or Carb Cleaner or Soap and Water Agitate/stir every few minutes until the outer surface is free of any engine debris Dry the filter using compressed air, blow air through the filter, (do not press the compressed air gun against the filter, keep at least a 10mm gap from nozzle to filter) starting from the inside out, then at an angle on the outside of the screen to further remove any remaining particles or cleaning solution. Once dry, reinstall O-Rings (MMR advices replacement of these O-Rings every oil service - See ES4810064) and refit into oil filter housing and engine. If you have any doubt about your ability to perform this sequence, we recommend replacing the filter element with each oil change.

Show More Show Less

Spark Plugs - Set Of Six

T#:14982199

Part#: 121200405516KT

Back Ordered

$ 95.99 USD

Add to Wish List

Qty

$ 95.99 USD

Add to Wish List

ARP Main Stud Kit - B58

T#:25241787

Part#: ARP-MSK-B58

Ships in 3 Business Days

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

This ARP Main Stud Kit is designed to replace BMW part numbers 11128644674 and 11127613127 for the B58; B58A, B58C, B58D engines found in varies BMW chassis One significant advantage of these main studs is their ability to prevent main cap walk, which can occur when the main caps shift or move out of position, potentially causing damage to the engine. In addition, ARP Main Studs can safeguard the threads of your engine block, providing an extra layer of protection against potential damage. When opting for main studs instead of factory bolts, it's important to note that the engine builder should mic the bores. Using studs may require a line hone to ensure proper fitment and alignment. A line hone is a machining process that can be used to resize and reshape the main bearing bores, ensuring that they are perfectly round and concentric. This is crucial for ensuring proper oil clearance and preventing premature bearing wear. By mic'ing the bores and performing a line hone if necessary, engine builders can ensure that the main studs are installed correctly and that the engine will perform reliably and at its best.

Show More Show Less

Performance Rod Bearing Set - N55

T#:26238416

Part#: 5150-HPRBS-N55

Ships in 3 Business Days

$ 399.99 USD

Add to Wish List

Qty

$ 399.99 USD

Add to Wish List

5150 High Performance Coated Rod Bearing Sets are made for the demands of high performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use, but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market.

Show More Show Less

CP-Carrillo Connecting Rod Set - CARR Bolts

Will Not Work With OE Pistons

T#:25473972

Part#: CAR-B58-SCR13034

Ships in 3 Business Days

$ 2,149.99 USD

Add to Wish List

Qty

$ 2,149.99 USD

Add to Wish List

CP-Carrillo connecting rods are highly esteemed in both racing and street performance communities for their exceptional quality and reliability. Renowned for their premium craftsmanship, CP-Carrillo produces top-tier products trusted by winning racers worldwide. Each connecting rod is meticulously crafted of a chrome-moly based alloy, reducing mass compared to stock rods while maintaining unparalleled strength. These rods undergo rigorous quality control measures, ensuring tight tolerances and precise balancing. Sold as matched and balanced sets, they come equipped with high-quality upgraded CARR rod bolts for increased clamping force. To clarify, these 148 mm connecting rods are specifically designed to fit BMW B58 engines. It's important to note that they are not compatible with factory OEM pistons.

Show More Show Less

5150 AutoSport High Performance Rod Bearing Set - BMW B58

T#:25241792

Part#: 5150-HPRBS-B58

Ships in 3 Business Days

$ 449.99 USD

Add to Wish List

Qty

$ 449.99 USD

Add to Wish List

CP-Carrillo Forged Piston Set - B58 Pro-Xtreme 82mm

T#:25241784

Part#: CP-FPS-B58-XT-HD

Ships in 3 Business Days

Starting at $ 1,599.99 USD

Add to Wish List

Starting at $ 1,599.99 USD

Add to Wish List

Curated by the expert engine builders at 5150 Autosport, this forged piston set is ready for anything you can throw at it. Curated by the expert engine builders at 5150 Autosport, this forged piston set is ready for anything you can throw at it. Tailored for the B58 engine with 148 mm Rods, these pistons are meticulously crafted to excel in high horsepower and high RPM scenarios. Constructed from aircraft-grade steel, these pistons are engineered to endure the forces produced by in high boost, high horsepower applications. Designed for extreme performance, the Pro-Xtreme Pistons can handle up to 2000 horsepower and engine speeds of up to 9,500 RPM! Each piston undergoes precision manufacturing, utilizing advanced techniques such as computer-aided design (CAD) and finite element analysis (FEA). The result is a set of Pro-Xtreme Pistons that are not only durable and reliable but also capable of withstanding the intense stresses and forces generated by high-horsepower and high-RPM engines. The Standard Compression Ratio on Most B58 Engines is 11:1 For reference. The Pro-Xtreme Piston Set Includes: Pistons PVD Rings HD Wrist Pins Locks Piston Spec Sheet Designed for extreme performance, the Pro-Xtreme Pistons can handle up to 2000 horsepower and engine speeds of up to 9,500 RPM! Each piston undergoes precision manufacturing, utilizing advanced techniques such as computer-aided design (CAD) and finite element analysis (FEA). The result is a set of Pro-Xtreme Pistons that are not only durable and reliable but also capable of withstanding the intense stresses and forces generated by high-horsepower and high-RPM engines. The Pro-Xtreme Piston Set Includes: Pistons PVD Rings HD Wrist Pins Locks Piston Spec Sheet

Show More Show Less

CP-Carrillo Connecting Rod Set - WMC Bolts

Will Not Work With OE Pistons

T#:25473971

Part#: B58-SCR13492

Ships in 3 Business Days

$ 1,844.99 USD

Add to Wish List

Qty

$ 1,844.99 USD

Add to Wish List

CP-Carrillo connecting rods are highly esteemed in both racing and street performance communities for their exceptional quality and reliability. Renowned for their premium craftsmanship, CP-Carrillo produces top-tier products trusted by winning racers worldwide. Each connecting rod is meticulously crafted of a chrome-moly based alloy, reducing mass compared to stock rods while maintaining unparalleled strength. These rods undergo rigorous quality control measures, ensuring tight tolerances and precise balancing. Sold as matched and balanced sets, they come equipped with high-quality WMC rod bolts. To clarify, these 148 mm connecting rods are specifically designed to fit BMW B58 engines. It's important to note that they are not compatible with factory OEM pistons.

Show More Show Less

5150 AutoSport & Cat Cams Camshaft Set - 278* / 272* - 11.20mm / 10.3...

T#:39126861

Part#: N55CCCAM-278-272

Ships in 3 Business Days

$ 1,799.99 USD

Add to Wish List

Qty

$ 1,799.99 USD

Add to Wish List

Cat Cams offer great performance at a reasonable price. Cat Cam offers cams in the most popular enthusiast upgrade specs to ensure there is an option for whatever your power goal is. This N55 camshaft set is designed to bring your engine to the next level! Whether it's for street or track purposes, this camshaft set offers the power gains and throttle response needed to push your N55 to its limits. These camshafts are a direct fit for seamless installation and with some simple tuning can produces great power while retaining factory-like idle and driveability. Valvetronic and Dual VANOS functionality can be fully retained, or with an aftermarket throttle body, the valvetronic system can be locked open, providing even more control.

Show More Show Less

MMX Billet Air Conditioning Caps - Pair Black

T#:48608191

Part#: MMR03-0004

Ships in 5 Business Days

$ 40.00 USD

Add to Wish List

Qty

$ 40.00 USD

Add to Wish List

The MMX Billet Air Conditioning Cap Set replaces cheap OEM pieces with durable aluminum replacements that withstand track thermal cycles and everyday driving.

BMW N55/S55 Valves By Super Tech

T#:39329323

Part#: SUP-HPVK-S55-32/

Ships in 3 Business Days

$ 1,143.99 USD

Add to Wish List

Qty

$ 1,143.99 USD

Add to Wish List

O-Ring Replacement Kit For MMX Performance Filter - BMW B58 & B58TU ...

T#:29035360

Part#: MMR17-0000

Special Order: No Guaranteed ETA

$ 13.99 USD

Add to Wish List

Qty

$ 13.99 USD

Add to Wish List

Genuine MMR Performance O-Ring service kit for the MMX Performance oil filter and billet housing. Does not include MMR oil filter or billet housing, only the four O-Rings needed to service our reusable filter. The MMR Performance oil filter and housing contains four O-Rings within the kit. We recommend you replace the O-Ring set on a regular basis when changing or cleaning the MMR filter, in order to maintain the integrity of the sealing properties it was designed to provide. As it's a direct replacement with the original O-Ring set supplied, it's a very straightforward process to swap and replace. Fitment is limited to the MMR Performance oil filter (MMR17-1502 - See ES4810063) to protect against the notorious B58 oil filter collapse

Show More Show Less

MMX Oil Pressure Gauge Adaptor - Black

T#:5269476

Part#: MMR03-0502KBL

Special Order: No Guaranteed ETA

$ 25.99 USD

Add to Wish List

Qty

$ 25.99 USD

Add to Wish List

The MMX Performance billet adaptor is a helpful addition for those wishing to run an auxiliary oil pressure or oil temperature gauge. The adaptor replaces the plug that can be found on the oil cooler thermostat assembly with a 1/8NPT gauge adaptor.

Show More Show Less

MMX Oil Thermostat Dress-Up Caps W/ Gauge Adaptor - Black

T#:5269479

Part#: MMR03-0502GBL

Special Order: No Guaranteed ETA

$ 111.99 USD

Add to Wish List

Qty

$ 111.99 USD

Add to Wish List

This dress-up kit offers a high-quality aesthetic update to the OE thermostat cover. Thermostat dress up kit for the BMW N55, N54, and S55 engines manufactured from T6061 billet aluminum. Installation is extremely easy and dresses up the engine bay nicely. Includes billet adaptor which is a helpful addition for those wishing to run an auxiliary oil pressure or oil temperature gauge. The adaptor replaces the plug that can be found on the oil cooler thermostat assembly with a 1/8NPT gauge adaptor. *Note: After exposure to excessive heat over prolonged periods, overall finish fading can occur.

Show More Show Less

MMX Performance Billet Oil Filler Cap

T#:28968889

Part#: MMR03-1601

Special Order: No Guaranteed ETA

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

MMX Washer Bottle Cap BMW F Series

T#:33379624

Part#: 634642

Special Order: No Guaranteed ETA

$ 77.99 USD

Add to Wish List

Qty

$ 77.99 USD

Add to Wish List

Billet Washer Bottle Cap for BMW F series By MMX

Spark Plug - Priced Each

T#:637736

Part#: 12120040551

Back Ordered

$ 15.99 USD

Add to Wish List

Qty

$ 15.99 USD

Add to Wish List

5150 AutoSport Pro-Series Turbo Build Kit, BMW / Toyota B58

T#:35761662

Part#: 5150-TBK-B58-G2-

Back Ordered

$ 5,149.99 USD

Add to Wish List

Qty

$ 5,149.99 USD

Add to Wish List

CP-Carrillo Custom Forged Piston Set - B58

T#:25274993

Part#: CP-FPS-B58-82

Back Ordered

Starting at $ 2,256.98 USD

Add to Wish List

Starting at $ 2,256.98 USD

Add to Wish List

CP-Carrillo sets the industry standard for high-quality pistons, meticulously crafted for optimal power and durability. Crafted with high-strength, lightweight materials and cutting-edge engineering, this BMW B58 piston set offers: Lightweight Design: Crafted from forged aluminum alloy and other high-strength materials, CP-Carrillo pistons ensure reduced weight for enhanced engine responsiveness and acceleration. Advanced Engineering: Employing state-of-the-art technology and engineering expertise, CP-Carrillo creates pistons that optimize combustion, boost fuel efficiency, and increase overall power output. Wide Configuration Range: Tailoring to diverse engine builds and performance goals, CP-Carrillo provides a range of bore sizes and compression ratios for customization. Quality Construction: Each CP-Carrillo piston undergoes precision machining, rigorous testing, and meticulous development, guaranteeing consistent quality and high performance. CP-Carrillo pistons stand as the superior choice for any B58 engine application, be it a street-driven powerhouse or a track-dominating machine. Engineered by one of motorsport's most esteemed names, these pistons elevate performance and reliability. The piston sets include Pistons, Rings, Pins, Locks, and a Spec Sheet. Optional Extras: Skirt Coating - Adding a Protective Layer Between the Sides of the Piston and Cylinder Walls Dome Coating - Adding a Protective Layer to the Top of The Piston HD-Wrist Pins - A Must if You are Planning on Going Beyond 850 HP! X Forging - Reducing Rotational Mass By Moving the Wristpin Inwards and Shortening it While Increasing Overall Strength

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW 3 Series F34 (2014+)

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Shipping

Narrow Results