BMW Coilovers for BMW 3 Series F34 (2014+)

The Bilstein B14 PSS Suspension allows adjustable vehicle ride height without the expense of a fully adjustable damping system. This system features both coilover and standard mono-tube gas pressure shock or struts with performance level valving for application specific, progressive rate coil springs.
The product benefits at a glance:

• Threaded body adjustable range of 20 mm
• Lowering of approx. 30-50 mm at front and rear
• Road-tested and fine-tuned by BILSTEIN ride engineers, under extreme motorsports conditions
• Aluminum Spring plates and lock nuts
• Surface coating using Triple-C-Technology for long-lasting corrosion resistance
• Round threads for easy adjustment
• Quality sport springs made from highly durable material
• Gas pressure technology

BILSTEIN monotube technology, made in Germany

adj. -1.0"-1.75" / adj. -1.0"-1.75"

Not for cars with EDC

This coilover kit fits the following BMWs:
2013+ F30/34 BMW 320i 328i/d 335i 330i 340i - xDrive models
2014+ F32/36 BMW 428i 435i 430i 440i - xDrive Coupes/Grand Coupes

​

The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

This coilover kit fits the following BMWs:
2014+ F22 BMW 228xi M235xi - Not for cars with EDC
2012+ F30 BMW 320xi 328xi 335xi - Sedan - Not for cars with EDC
2013+ F32 BMW 428xi 435xi - Coupe - Not for cars with EDC
2014+ F34 BMW 328i xDrive GT, 335i xDrive GT - Gran Tourismo
2014+ F36 BMW 428i xDrive Gran Coupe 435i xDrive Gran Coupe

The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

Fits the Following Vehicles:
2012+ BMW F30 328i 328d 320i 335i 330e 330i 340i
2014+ BMW F32/F36 428i 435i 430i 440i
2014-2016 BMW F22 228i

The ECS BMW Coilover line was designed with daily drivers in mind! The ECS engineer's focus was to improve the performance and look of the suspension, without forgoing ride comfort. Like many top-tier coilovers, these coilovers feel as smooth and comfortable as a stock setup, while also providing an aggressive look and vastly improved handling.

The ECS Performance Coilover System provides a sport-tuned, height, damping, and body adjustable suspension with substantial performance benefits using high-quality materials and coatings to replace your worn suspension, all while giving your vehicle that perfect ride height!

Spring Rates: 8kg/mm (front), 12kg/mm (rear)

PERFORMANCE FEATURES

32 levels of rebound damping adjustment Adjustable damping, monotube shocks/struts paired with optimized progressive rate coil springs give your vehicle road-sticking grip with reduced body roll for exceptional confidence in your vehicle's handling. With your vehicle's new, lower ride height the center of gravity is now moved lower, further improving handling performance Adjustable front bodies allow you to set the ride height while maintaining correct spring pre-load Adjustable front and rear bodies allow the shock to operate in the correct valving range, regardless of ride height PRODUCT DESIGN

Strut and shock bodies finished with a durable gloss black powder coat for good looks and great longevity Threaded portions are clear zinc-coated for optimum corrosion protection against rain and salt Coil springs are powder-coated Reflex Silver Metallic finish for durability Red anodized, billet aluminum lower spring seats with locking collars allow for quick, on-the-car, adjustability with the included spanner wrenches Integrated bump stops KIT CONTENTS

ECS Performance Adjustable Coilover System - F2X/F3X (3-Bolt) Front Suspension Installation Hardware Strut Mount Gasket - 31306868240 (2) Spindle Pinch Bolt - 31306798530 (2) Spindle Pinch Nut - 07119905032 (2) Tension Strut Bolt - 31106885777 (2) Control Arm Bolt - 31106797237 (2) Control Arm Nut - 33326760668 (2) Ball Joint Locking Nut - 33306787062 (4) CV Axle Bolt - 31206795249 (2) Rear Suspension Installation Hardware Shock to Control Arm Bolt - 07119907372 (2) Shock to Control Arm Nut - 33326760668 (2) Shock Mount Bolt - 07119907137 (6) Shock Mount Gasket - 33506866038 (2) Control Arm to Wheel Carrier Bolt - 33326762875 (2) Control Arm to Wheel Carrier Nut - 33306760349 (2)

The ECS BMW Coilover line was designed with daily drivers in mind! The ECS engineer's focus was to improve the performance and look of the suspension, without forgoing ride comfort. Like many top-tier coilovers, these coilovers feel as smooth and comfortable as a stock setup, while also providing an aggressive look and vastly improved handling.

The ECS Performance Coilover System provides a sport-tuned, height, damping, and body adjustable suspension with substantial performance benefits using high-quality materials and coatings to replace your worn suspension, all while giving your vehicle that perfect ride height!

Spring Rates: 8kg/mm (front), 10kg/mm (rear)

PERFORMANCE FEATURES

32 levels of rebound damping adjustment Adjustable damping, monotube shocks/struts paired with optimized progressive rate coil springs give your vehicle road-sticking grip with reduced body roll for exceptional confidence in your vehicle's handling. With your vehicle's new, lower ride height the center of gravity is now moved lower, further improving handling performance Adjustable front bodies allow you to set the ride height while maintaining correct spring pre-load Adjustable front and rear bodies allow the shock to operate in the correct valving range, regardless of ride height PRODUCT DESIGN

Strut and shock bodies finished with a durable gloss black powder coat for good looks and great longevity Threaded portions are clear zinc-coated for optimum corrosion protection against rain and salt Coil springs are powder-coated Reflex Silver Metallic finish for durability Red anodized, billet aluminum lower spring seats with locking collars allow for quick, on-the-car, adjustability with the included spanner wrenches Integrated bump stops KIT CONTENTS

ECS Performance Adjustable Coilover System - F2X/F3X (3-Bolt) Front Suspension Installation Hardware Strut Mount Gasket - 31306869890 (2) Spindle Pinch Bolt - 31306798530 (2) Spindle Pinch Nut - 07119905032 (2) Tension Strut Bolt - 31106885777 (2) Control Arm Bolt - 31106797237 (2) Control Arm Nut - 33326760668 (2) Ball Joint Locking Nut - 33306787062 (4) Rear Suspension Installation Hardware Shock to Control Arm Bolt - 07119907372 (2) Shock to Control Arm Nut - 33326760668 (2) Shock Mount Bolt - 07119907137 (6) Shock Mount Gasket - 33506866038 (2) Control Arm to Wheel Carrier Bolt - 33326762875 (2) Control Arm to Wheel Carrier Nut - 33306760349 (2)

Fine-tuning your coilover damping shouldn’t mean stripping out your rear seats or interior panels. On many applications, rear shock adjusters are hidden behind carpet, trim, or seatbacks, making quick adjustments a hassle.

The ECS Rear Damping Extension Kit solves that problem with a clean and functional solution. These flexible extensions relocate the adjustment knobs to an easily accessible point above the rear shock towers, letting you dial in your suspension from inside the cabin, no disassembly required.

Installation is straightforward: simply drill a small access hole in your interior trim and route the extension cables through. The adjustment knobs can be removed to allow the line to pass through smaller openings, minimizing cutting. For proper installation, be sure to fully loosen the set screw, insert the cable, then securely tighten it using the provided Allen key.

Kit Includes:

(2) Rear damping adjuster extension cables

Installation hardware and Allen key

A smart upgrade for track cars, daily drivers, or anyone who values easy access to suspension tuning, without compromising interior fit and finish.