Intercooler for BMW 4 Series F36 (2015+)

Wagner Competition intercoolers (#200001071) are engineered in Germany to be a superior N20/N55 intercooler than the factory part. With 85% more surface area and 90% more volume than the factory IC the Wagner-designed kit is much more efficient. And that helps maintain your boost levels and performance! The factory intercooler is quickly overcome with heat and that leads to a loss of boost and performance. Factor in greater boost levels and other modifications and the more heat soak will put you out of the running. The solution is an intercooler with more capacity for cooling and the best intercooler upgrade is one that not only works but also installs with a minimum amount of fuss. 

This competition intercooler kit utilizes a tube fin center core unit, for cooler temperatures and less pressure drop. This is for ideal for owners who are going to install a tuner, build a competition car or operate in hot climates. This can be used on the street, track, and for an everyday driving and will allow cooler temps and more air flow through the core! 

Compared to the stock OEM intercooler:


One of the best features of this kit is that it's a direct bolt-on replacement for your stock intercooler - no removing the bumper or modifying brackets or wrestling with plumbing. Wagner has also engineered their end-tanks in aluminum instead of the factory plastic, which is much more durable over the long term. The CAD and FEM process also allows them to design their cooler internals without any bottlenecks or restrictions. This is just the best all-around intercooler upgrade we have seen for the F30 335! Fits both N20 and N55 cars. 

Size Comparison
LDH
Wagner Performance  520mm x 215mm x 145mm /stepped with a 13.8cm flow rate weighing 8.6 grams
stock OEM                  510mm x 130mm x 110mm with a 7.3 cm flow rate

This FMIC fits the following BMWs:
2014+ F22 BMW 228i M235i
2016+ F87 BMW M2
2012+ F30 BMW 320i 328i 335i - Sedan
2012+ F31 BMW 328i - Wagon
2014+ F34 BMW 328i xDrive GT, 335i xDrive GT - Gran Tourismo
2014+ F32 BMW 428i 435i 435iX - Coupe
2014+ F36 BMW 428i Gran Coupe 428i xDrive Gran Coupe 435i Gran Coupe 435i xDrive Gran Coupe
 

Engines make more power when you're able to move as much air and fuel as possible through them. However, air density is just as important as air volume. Cooler air is denser air, so in addition to keeping your engine cool, it's important to make sure that your intake charge is as cool as possible. Turner Motorsport's upgraded intercooler works to reduce air temperatures with a bare minimum of pressure drop. Less pressure drop means less restriction, and a turbocharger that doesn't have to work as hard. This results not only in a longer service life for your turbocharger, but a substantial increase in performance as well.

The stepped design increases volume and surface are in a limited space by adding an additional smaller core at the top of the intercooler. Both cross sectional area and frontal surface area are increased by a whopping 56%, with a design that still weighs under 20 pounds. On the stock intercooler, the temperature differential between the inlet and outlet sides of the intercooler represented a 95 degree drop. With the Turner Motorsport intercooler, that drop was increased to a chilling 140 degrees. The dyno results don't lie: as a bolt-in upgrade, expect gains of 18 wheel horsepower and 10 lb/ft of torque. With a tune and supporting modifications, further gains are possible, up to 36 horsepower and 28 lb/ft of torque.

This cast aluminum intercooler features an attractive, easy to clean matte black finish, with etched Turner logos on the front and bottom. If you're looking for the ultimate cooling system upgrade for your turbo BMW, look no further.

• Cast aluminum construction
• Bar and plate design
• 56% increase in frontal surface area & cross sectional area
• Decrease in temperature of 45 degrees from inlet side to outlet side (95 degree drop stock on outlet side vs. 140 degree drop on Turner outlet side)
• Significantly less restriction (pressure drop of consistently 0.75 psi vs. 1.5-2.5 psi stock)
• +18HP/10TQ (+36HP/28TQ with tune and supporting mods)
• Weighs under 20 lbs.
• Overall size: 520mm wide, 210mm tall
• Mounting hardware inlcuded

Upgrade to the following OE Intercoolers: 17517600531, 17517600530, 17517618809

Fits the Following BMWs:

F22 F23 228i 228i M235i M235ix

F30 F31 F32 F33 F34 F36 328i 328ix 335i 335ix 428i 428ix 435i 435ix