BMW Tools & Specialty Equipment for BMW F83 M4 S55 3.0L

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
• Deluxe transverse support for even more stability
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

WHEEL STORAGE RACK:

Now you can stack your extra wheels without the danger of scratches and scuffs. This wheel storage rack keeps your wheels spaced apart, and being on locking casters, allows you to easily move the whole set anywhere in your garage or shop at one time. Sturdy steel construction and a wide base means this wheel rack won't tip over. Holds up to 275 lbs - enough for most any wheel & tire set.

Fits up to 8½" wide wheels, depending on offset

TIRE STACK COVER:

This tire stack by Schwaben is the solution to keeping your tires and wheels clean while in storage.

• Works with 4 tire stacks and works great with our Schwaben Wheel Tree (ES2710754).
• Durable 150D coated material is rated for outdoor use.
• Cover is a large 32" wide X 46" tall.
• Fitted with a long 29" zipper up the side for easy installation and removal.
• Nylon draw string at the bottom allows for a good snug fit.
• Includes a handy storage pouch if not in use.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

This professional-grade deluxe fender roller allows you to gently and gradually flatten your inner fender lips in order to increase your fender to tire clearance.

This new deluxe fender roller has been designed to fit most applications.

This is the perfect tool for:

If you want to lower your vehicle
If you want wider-than-stock wheels
If you are going to use wheel spacers or decreased offset
Will work with bolt patterns of 4x100 and 5x100 up to 4x114.3 and 5x130 with 12mm or 14mm lug bolts.

By rolling the fender lip flat, you can lower your car further, and give your car a wider stance, without your tires rubbing on the inside of the fender.

Fully adjustable for use on vehicles of different ride heights, offsets, and wheel bolt patterns.

Use of a heat gun is recommended to soften the fender surface during the rolling process and prevent paint cracking.

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

Ensure safe and professional jacking of your BMW, 2020 Supra, or MINI with the Turner Motorsport Jack Pad Adapter. Designed to mimic the factory scissor jack, this adapter allows for secure lifting at any of the 4 factory jack points without causing damage to your vehicle. Made in the USA from solid billet aluminum, it features the Burger Motorsports logo and a honeycomb grip pattern for stability. Simple to use and compatible with most floor jacks, it ensures correct and secure lifting every time. Here are the key benefits:

• Safely lifts your BMW, 2020 Supra, or MINI at factory jack points
• Prevents damage to rocker panels or vehicle undercarriage
• Made from solid billet aluminum for durability
• Engraved Burger Motorsports logo for authenticity
• Honeycomb grip pattern for stability during use

 This comprehensive kit is basically a one-stop-shop to pick up all the special torx, triple square, & hex bits you need to keep your car where it should be... on the road!

This Universal European Tool Kit features the following:

• Torx Screwdriver Kit - 6 Pieces (Sizes included: T10, T15, T20, T25, T27, & T30. Perfect for removing door and dashboard panels, interior trim, and smaller underhood components. )
• Swivel Head Triple Square Driver Kit - 4 Pieces (Set of four 3/8 drivers in M6, M8, M10, and M12 sizes. Perfect for working around corners in those hard to reach spots.)
• Specialty Bit Kit - 100 Pieces (100 piece torx & hex bit kit to fit a wide assortment of automotive fasteners. Made of hardened Chrome Vanadium steel, packaged in a handy blow molded case.)
• Go-Through Screwdriver Kit - 6 Pieces (Kit includes durable slotted & phillips head nickel-chromoly screwdrivers with hardened shafts that extend the entire length of the driver.)

When it comes to the torque found on axle nuts you're already looking at using a breaker bar or impact gun not to mention the corrosion collected over the years. The safest approach is using impact socket, since they are built with the strength needed to avoid breaking under pressure.

Features:

• Heavy duty ½ inch-drive sockets and drivers have extra thick alloy steel walls, and take a beating that would destroy normal sockets
•  Durable black oxide coating wipes clean easily and resists rust
• Contains three 12-point sockets for a sure grip on the most common sized axle nuts, plus three hex drives for removing common hex-head plugs and fasteners
• Conveniently packaged in a blow molded case, this set will please the most demanding professional technician or discriminating prosumer

Kit includes:

• 30mm, 32mm, and 36mm - 12-point axle nut sockets - ½" drive

• 14mm, 17mm, and 19mm hex head drive axle shoulder bolt sockets - ½" drive

Don’t let a dead battery or flat tire ruin your day. The Schwaben 4-In-1 Jump Pack & Tire Inflator is your all-in-one roadside emergency solution—compact, powerful, and built to keep you moving. Engineered for versatility, this unit combines a high-output lithium-ion jump starter, a digital tire inflator, a bright LED flashlight, and a portable power bank—delivering everything you need in a single, easy-to-carry package.

Whether it’s a weak battery on a cold morning or low tire pressure before a long drive, the Schwaben Jump Pack is ready to go. With 2500 peak amps, it can jump-start most 12V gas or diesel engines up to 6.0L. The integrated 150 PSI air compressor features a digital pressure readout and auto shutoff for precise inflation, while USB-A and USB-C ports let you charge your phone, tablet, or other devices. A 300-lumen LED flashlight with steady, strobe, and SOS modes ensures you’re never left in the dark.

Product Features:

12V Lithium-Ion Power Supply: 2500A peak, 74Wh capacity Digital Air Compressor: 150 PSI max with auto shutoff and pressure readout Power Bank Functionality: USB-A and USB-C compatible, 60W total output 300-Lumen LED Flashlight: Includes strobe and SOS emergency modes Rugged Design: Insulated, keyed battery cables and braided air hose with threaded fitting Kit Includes:

Schwaben 4-In-1 Jump Pack & Tire Inflator Jumper Cables & Clamps Braided Air Hose Nozzle Adapters USB-C to USB-C Charging Cable (for recharging unit) USB-A to USB-C Charging Cable (for devices) Knit Storage Bags User Manual

3/8" DRIVE LONG FLEX HEAD RATCHET:

A professional quality flex ratchet features a fine satin finish designed for durability and easy clean up.

Features:

• Special designed 72T gear mechanism
• 5 degree of handle movement between gears 
• Flex head has 7 detent positions in a 180 degree swing
• Push button release holds socket tight until you are ready to release
• Ratchet is a full 290mm ( 11") long for extra leverage.

3/8" DRIVE 6 POINT SOCKET SET:

A satin chrome finish with a knurled ring around socket body, the knurling allows for a better grip when hands and sockets are covered in oil or grease. All sockets feature a radius in the corners for superior torque to the sides of the fastener, not the corner. Complete size coverage.

Includes:

• 8mm
• 9mm
• 10mm
• 11mm
• 12mm
• 13mm
• 14mm
• 15mm
• 16mm
• 17mm
• 18mm
• 19mm

LIFETIME REPLACEMENT on all items in this kit!

Aluminum 3-Ton Jack Stands With Mechanic's Folding Ground Pad - Set Of 2 are designed for exceptional performance and convenience in automotive maintenance. These lightweight aluminum jack stands provide robust support, while the mechanic's folding ground pad ensures comfort during vehicle work.

• Lightweight Construction: Each jack stand weighs only 4.7 lbs, making them easy to handle without sacrificing strength.
• Durable Design: All-aluminum construction with heavy-duty flanged bases ensures stability and safety for loads up to 3 tons.
• Adjustable Heights: Features 6 locking positions with a minimum height of 10.6 inches and a maximum height of 15.4 inches.
• Secure Load: Extra heavy-duty load pin with a posi lock ball mechanism keeps the pin securely in place.
• Large Base: Equipped with a 7-inch diameter base for enhanced stability.
• Mechanic’s Ground Pad: Provides comfort with high-density foam and a heavy-duty cover that resists oils and fluids. Measures 17"W x 47"L when unfolded and includes built-in carrying handles.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Correct toe settings contribute to both stable steering and even tire wear. The SPC Performance wheel toe bar tool is designed to prevent vehicle drifting and ensure uniform tire wear. It includes a steel bar equipped with sliding adjusters and pointers to accurately assess the vehicle's toe alignment.

For wider wheel bases use T#386442!

This socket set is the perfect tool for axle nuts when servicing the axle shafts or wheel bearings.

Features:

• ½-inch drive 12-point socket
• Specially hardened to take the added abuse from a impact gun
• Coated for added protection and so you can tell it apart from non impact rated sockets
• Made of durable chrome moly steel
• 24mm (65mm depth)
• 27mm (65mm depth)
• 30mm (53mm depth)
• 36mm (65mm depth)
• 46mm (75mm depth)