BMW Tools & Specialty Equipment for BMW X Series G07 X7 (2019+)

Designed for precision and durability, the VIM Tools 10 Piece Half Cut Stubby Torx Driver Set offers an updated solution for Torx applications. This new version of the HCT1050 is now packaged on a green Magrail, delivering a streamlined organization system for your tools.

With sizes ranging from T10 through T50, each driver features a 1/4" square drive and a compact 3/4" overall length, perfect for tight spaces. Crafted from heat-treated S2 steel with a satin chrome finish, these drivers ensure long-lasting performance and corrosion resistance.

Key Features:

• Wide Range of Sizes: T10 through T50 to cover various applications.
• Compact Design: 1/4" square drive with 3/4" overall length for hard-to-reach areas.
• Durable Build: Heat-treated S2 steel for enhanced strength and durability.
• Satin Chrome Finish: Corrosion-resistant and easy to clean.
• Half Cut Design: 1/2" cut drivers offer precise fitment.
• Magnetic Organization: Packaged on a green Magrail for convenient storage.

Includes:

• T10 (HCT10-04)
• T15 (HCT15-04)
• T20 (HCT20-04)
• T25 (HCT25-04)
• T27 (HCT27-04)
• T30 (HCT30-04)
• T40 (HCT40-04)
• T45 (HCT45-04)
• T47 (HCT47-04)
• T50 (HCT50-04)

If you're refreshing your struts and springs this tool is a must, properly compress the springs, easily remove and install the strut nut, and smoothly remove the spindles.

Features:

• Spring Compressor
• Strut Nut Sockets
• Spindle Spreader

• Tough and rigid expanded polystyrene foam (EPS) with a load rating of 1,500lbs per wheel (almost twice what the normal corner weight would be on a 3-series BMW)
• 12" height X 12" width with minimal compression under load
• Light weight with each block weighing less than 6lbs and with a handy strap for carrying or hanging
• Curved cradle for the tire to sit inside
• Non-skid surface that won't scratch your floor

Looking for an alternative to your jack stands? With these wheel blocks you won't have to think twice about a jack stand scratching or denting the underside of your floor or the car falling off the jack stand. These work best when used with a floor jack under the subframe and the opposite axle wheels chocked. These are also a light weight and inexpensive alternative to the super-pricey plastic and metal ramps. They are resistant to most fluids and chemicals (but not solvents) and will never rust unlike metal ramps and blocks.

Also available in a 10" height.

Elevate your lifting experience with the Schwaben Long Low Profile - High Lift Floor Jack. Certified for excellence and designed with a keen understanding of European car enthusiasts' needs, this jack is a testament to precision, durability, and performance. Don't compromise on quality—choose the Schwaben advantage for all your lifting endeavors.

Designed with precision, crafted for performance, and backed by our lifetime replacement program, the Schwaben Long Low Profile - High Lift Floor Jack is a must-have tool for every European car aficionado. This jack is engineered to cater to the unique needs of low ground clearance vehicles, ensuring that your prized possessions are lifted with care and precision.

Key Features:

• One Pump Reach: With its innovative one-pump feature, this floor jack effortlessly reaches contact on most cars, streamlining your lifting process.
• Low Profile Advantage: Boasting a mere 2-3/4" low height and a deep-reach lift arm, this jack is tailored for those sports cars and luxury vehicles that ride close to the ground.
• Hydraulic System Protection: The dual pump pistons are expertly shielded to thwart contaminants from compromising the hydraulic system's integrity.
• Built for Durability: Crafted with heavy gauge construction and fortified with rolled edges, this floor jack guarantees unwavering strength and longevity.
• Precise Control: The U-Joint release mechanism offers meticulous control over load descent at any handle position, ensuring the safety of both you and your vehicle.
• Maneuverability Redefined: Upgraded casters allow seamless maneuverability and effortless positioning of the jack, empowering you to find that perfect lifting spot.
• Safety First: The internal by-pass valve prevents over-pumping, shielding the hydraulic system from stress-induced issues.
• Vehicle Protection: A full cover rubber saddle pad and a protective foam cover on the handle are in place to prevent any unintended damage during the lifting process.
• Impressive Capacity: With a remarkable 4000 lb. capacity, this jack is ready to tackle a range of European vehicles.
• LIFETIME REPLACEMENT: Like almost all Schwaben products, this jack is backed by our lifetime replacement program in case anything goes wrong!

Specifications:

• Min Height: 2-3/4"
• Max Height: 24"
• Handle Length: 49-1/4"
• Jack Body Length: 35"
• Length from Pivot Point to Center of Jack Pad: 22"
• Front Casters: 2-1/2" diameter x 2" width
• Saddle Diameter: 4" with full saddle pad
• Weight Capacity: 4000 lbs.
• ANSI / ASME PALD 2009 Certified

Also included are the Schwaben Aluminum 3-Ton Jack Stands. These ultra-light Schwaben jack stands only weigh 4.7 lbs each. Fit and finish on these stands show how much pride in workmanship goes into our stands. These stands feature all-aluminum construction with heavy-duty flanged bases to safely stabilize loads. Features 6 locking positions for a secure load in multiple heights. The load pin is extra heavy duty at .584 in. diameter and features a posi lock ball to ensure the pin stays in place.  

• Min. Height is 10.6".
• Max Height is 15.4".
• Large 7" diameter base.
• Outer support tube is 2-1/8" in diameter.

For replacement parts, please call us and ask for:

• ES#4430428 - Replacement Screw Set
• ES#4430429 - Replacement Front Wheel
• ES#4430430 - Replacement Caster Wheel

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Provides access to recessed areas with extra long bolts, as found on some bumpers, rear lamps, diesel glow plugs (10mm, 12mm, 17mm), spark plugs, and door hinge fittings.

Areas where this tool set is helpful includes a range of specific applications such as BMW N54 Twin-turbo valve cover bolts (12mm), BMW E90/92 Lug Nuts (17mm), BMW Spark Plugs (14mm), BMW E90/92 Clutch Bleeder Valve (11mm), and other common Euro applications.

Kit includes: 

• 1/4" adapter
• 8mm
• 9mm
• 10mm
• 11mm
• 12mm
• 13mm
• 14mm
• 15mm
• 16mm
• 17mm
• 18mm

46 PIECE SET:

This 1/4" set contains all the most popular tools needed to get the job done on your European car repair.

Kit Contains:

-13PCS-1/4" DR.6PT SOCKETS: 4, 4.5 , 5 ,5.5 ,6 , 7, 8 ,9 ,10, 11, 12, 13, 14MM 

-1PC- 1/4" DR. QUICK RELEASE RATCHET (72T).

-2PC- 1/4" DR.50 & 100MM EXTENSIONS 

-1PC- 1/4" DR.150MM FLEXIBLE EXTENSION

-1PC- 1/4" DR.UNIVERSAL JOINT

-1PC- 1/4" DR.SLIDING T-BAR

-1PC- 1/4" DR.6" SPINNER HANDLE

-1PC- 1/4" DR.1/4" BIT HOLDER ADAPTER

-4PCS-HEX KEY WRENCHES:1.27, 1.5,2,2.5MM

-6PCS-1/4" HEX SOCKETS:3,4,5,6,7,8MM

-3PCS-1/4' SLOTTED SOCKETS:4,5.5,7MM

-3PCS-1/4" PHILIPS SOCKETS:PH1, PH2, PH3

-3PCS-1/4"POZI SOCKETS: PZ1, PZ2, PZ3

-6PCS-1/4" TORX SOCKETS: T10, T15, T20, T25, T30, T40

TRIM/MOLDING SET:

Plastic five-piece tool kit removes trim and door panels, moldings, and adhesive backed logos and badges, without damage.

Made of impact resistant plastic that will not mar surfaces as metal screwdrivers and pry bars will. Slim design for delicate work in tight areas.

Kit includes:

• Wide edge remover

• Narrow edge remover

• Pull-type remover

• Handle remover

• Upholstery clip remover

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

This large socket is the perfect tool for axle nuts when servicing the axle shafts or wheel bearings.

Features:

• ½-inch drive 36mm 12-point socket
• Specially hardened to take the added abuse from a impact gun
• Coated for added protection and so you can tell it apart from non impact rated sockets
• 75mm depth  to accommodate many applications and different length shafts
• Made of durable chrome moly steel